BS EN 50464-3-2007 Three-phase oil-immersed distribution transformers 50 Hz from 50 kVA to 2500 kVA with highest voltage for equipment not exceeding 36 kV - Determination of the pos.pdf

1、 g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58transformers 50 Hz, from 50 kVA to 2 500 kVA with highest voltage for equipment not exceeding 36 kV

2、 Part 3: Determination of the power rating of a transformer loaded with non-sinusoidal currentsThe European Standard EN 50464-3:2007 has the status of a British StandardICS 29.180Three-phase oil-immersed distribution BRITISH STANDARDBS EN 50464-3:2007BS EN 50464-3:2007This British Standard was publi

3、shed under the authority of the Standards Policy and Strategy Committee on 31 August 2007 BSI 2007ISBN 978 0 580 57702 4Amendments issued since publicationAmd. No. Date Commentscontract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from

4、legal obligations. National forewordThis British Standard is the UK implementation of EN 50464-3:2007. It supersedes BS 7821-4:1995 which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee PEL/14, Power transformers.A list of organizations represented on this c

5、ommittee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a EUROPEAN STANDARD EN 50464-3NORME EUROPENNE EUROPISCHE NORM April 2007 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation El

6、ectrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B - 1050 Brussels 2007 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 50464-3:2007 E ICS 29.180 Supersedes HD 428.4 S1:1994E

7、nglish version Three-phase oil-immersed distribution transformers 50 Hz, from 50 kVA to 2 500 kVA with highest voltage for equipment not exceeding 36 kV - Part 3: Determination of the power rating of a transformer loaded with non-sinusoidal currents Transformateurs triphass de distribution immergs d

8、ans lhuile, 50 Hz, de 50 kVA 2 500 kVA, de tension la plus leve pour le matriel ne dpassant pas 36 kV - Partie 3: Dtermination de la caractristique de puissance dun transformateur avec des courants de charge non sinusodaux lgefllte Drehstrom-Verteilungstransformatoren 50 Hz, 50 kVA bis 2 500 kVA, mi

9、t einer hchsten Spannung fr Betriebsmittel bis 36 kV - Teil 3: Bestimmung der Bemessungsleistung eines Transformators bei nichtsinusfrmigen Laststrmen This European Standard was approved by CENELEC on 2007-02-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which sti

10、pulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Stand

11、ard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the nation

12、al electrotechnical committees of Austria, Belgium, Bulgaria, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden,

13、 Switzerland and the United Kingdom. EN 50464-3:2007 - 2 -Foreword The text of the Harmonization Document HD 428.4 S1:1994, prepared by the Technical Committee CENELEC TC 14, Power transformers, was submitted to the formal vote for conversion into a European Standard and was approved by CENELEC as E

14、N 50464-3 on 2007-02-01. The following date was fixed: latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2008-02-01 The EN 50464 series consists of the following parts, under the general title “Three-phase oil

15、-immersed distribution transformers 50 Hz, from 50 kVA to 2 500 kVA with highest voltage for equipment not exceeding 36 kV” : Part 1 General requirements Part 2-1 Distribution transformers with cable boxes on the high-voltage and/or low-voltage side General requirements Part 2-2 Distribution transfo

16、rmers with cable boxes on the high-voltage and/or low-voltage side Cable boxes type 1 for use on distribution transformers meeting the requirements of EN 50464-2-1 Part 2-3 Distribution transformers with cable boxes on the high-voltage and/or low-voltage side Cable boxes type 2 for use on distributi

17、on transformers meeting the requirements of EN 50464-2-1 Part 3 Determination of the power rating of a transformer loaded with non-sinusoidal currents Part 4 Requirements and tests concerning pressurised corrugated tanks EN 50464-3:2007 - 3 -Contents 1 Scope4 2 Normative references4 3 Application.4

18、4 Equivalent power rating.4 5 Calculation of the factor K to obtain the equivalent power rating 5 EN 50464-3:2007 - 4 -1 Scope This European Standard gives to the user guidance to determine the loadability of an oil-immersed distribution transformer, as defined in and covered by EN 50464-1, in the c

19、ase of load current with harmonic factors exceeding the maximum values allowed. NOTE In general this document is also applicable to dry-type distribution transformers as defined in and covered by HD 538. 2 Normative references For the purposes of this document, the normative references of EN 50464-1

20、 apply. 3 Application For normal electrical energy distribution, the allowable total harmonic factor 1)and even harmonic factor of the load current are assumed to be limited to 5 % and 1 % respectively. For electrical distribution with higher harmonic factors, it has to be taken into account that th

21、e load loss increases and, by consequence, the temperature rises in the transformer exceed those corresponding to sinusoidal currents having the same r.m.s. value. NOTE If the transformer is intended for converter operation or the harmonic factor is higher than 5%, the matter shall be discussed betw

22、een purchaser and manufacturer. 4 Equivalent power rating The equivalent power rating is related to sinusoidal current which causes the same losses as those occurring with the non-sinusoidal current imposed. The equivalent power rating is equal to the power based on the r.m.s. value of the non-sinus

23、oidal current multiplied by the factor K. The rated power of the transformer to be used shall be equal to or higher than the equivalent power rating. In case a transformer in service is subsequently loaded with harmonic currents, a derating factor 1/K shall be applied to the rated power. 1)The harmo

24、nic factor H, in percentage, is defined by: 21221100%=NnnnIIH EN 50464-3:2007 - 5 -5 Calculation of the factor K to obtain the equivalent power rating The factor K is given by the following formula 2): 2122 12111+=NnnnqIInIIeeKwhere e = the eddy current loss due to sinusoidal current at fundamental

25、frequency (e.g. 50 Hz), divided by the loss due to a d.c. current equal to the r.m.s. value of the sinusoidal current, both at reference temperature; n = harmonic order; I = the r.m.s. value of the sinusoidal current and, in the other case, of non-sinusoidal current, containing all harmonics, given

26、by 2121112112=NnnnNnnnIIIIIIn = the nth harmonic current (amplitude or r.m.s. value); I1 = the fundamental current (amplitude or r.m.s. value); q = an exponential constant 3). 2)In the formula it is assumed that both power ratings are based on the same r.m.s. value of the load current. 3)The exponen

27、t q is dependent on the type of windings and on the frequency. However as an approximation and as a guidance, the following constant values may be used: 1,7 for transformers with round or rectangular wire in both the low and high voltage windings; 1,5 for transformers having low voltage foil winding

28、s. Other values, based on measurements and possibly frequency dependent, may be applied by agreement between purchaser and manufacturer. BS EN BSI389 Chiswick High RoadLondonW4 4AL50464-3:2007BSI British Standards InstitutionBSI is the independent national body responsible for preparing British Stan

29、dards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.It is the constan

30、t aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:

31、+44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed t

32、o Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-.In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as Br

33、itish Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give de

34、tails on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-.Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of

35、these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-.Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- information about BSI is available on the BSI web

36、site at http:/www.bsi-.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrie

37、val system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI.This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.