1、BRITISH STANDARD BS EN 60034-7:1993 IEC 60034-7:1992 Incorporating Amendment No. 1 Rotating electrical machines Part 7: Classification of types of construction, mounting arrangements and terminal box position (IM Code) The European Standard EN 60034-7:1993 with the incorporation of amendment A1:2001
2、 has the status of a British Standard ICS 29.160.01 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBS EN 60034-7:1993 This British Standard, having been prepared under the direction of the Power Electrical Engineering Standards Policy Committee, was published under the authori
3、ty of the Standards Board and comes into effect on 15 October 1993 BSI 5 October 2001 The following BSI references relate to the work on this standard: Committee reference PEL/1 Draft for comment 87/25137 DC ISBN 0 580 22563 1 Cooperating organizations The European Committee for Electrotechnical Sta
4、ndardization (CENELEC), under whose supervision this European Standard was prepared, comprises the national committees of the following countries: Austria Italy Belgium Luxembourg Denmark Netherlands Finland Norway France Portugal Germany Spain Greece Sweden Iceland Switzerland Ireland United Kingdo
5、m Amendments issued since publication Amd. No. Date Comments 13216 5 October 2001 See national forewordBS EN 60034-7:1993 BSI 5 October 2001 i Contents Page Cooperating organizations Inside front cover National foreword ii Foreword 2 Text of EN 60034-7 3 National annex NA (informative) Committees re
6、sponsible Inside back coverBS EN 60034-7:1993 ii BSI 5 October 2001 National foreword This British Standard has been prepared under the direction of the Power Electrical Engineering Standards Policy Committee and is the English language version of EN 60034-7:1993 Rotating electrical machines Part 7:
7、 Classification of types of construction mounting arrangements, and terminal box position (IM Code) including amendment A1:2001 published by the European Committee for Electrotechnical Standardization (CENELEC). It was derived by CENELEC from IEC 60034-7:1992 including amendment 1:2000 published by
8、the International Electrotechnical Commission (IEC). This British Standard supersedes BS 4999-107:1987 which is withdrawn. The start and finish of text introduced or altered by amendment is indicated in the text by tags . Tags indicating changes to IEC text carry the number of the IEC amendment. For
9、 example, text altered by IEC amendment 1 is indicated by . From 1 January 1997, all IEC publications have the number 60000 added to the old number. For instance, IEC 27-1 has been renumbered to IEC 60027-1. For a period of time during the change over from one numbering system to the other, publicat
10、ions may contain identifiers from both systems. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obliga
11、tions. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, the EN title page, pages 2 to 25 and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued.EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM E
12、N 60034-7 January 1993 +A1 March 2001 UDC 621.313:001.4:003.62 Supersedes HD 53.7 S1:1974 Descriptors: Rotating electrical machine, classification, designation, types of construction, mounting arrangements, IM code English version Rotating electrical machines Part 7: Classification of types of const
13、ruction, mounting arrangements and terminal box position (IM Code) (includes amendment A1:2001) (IEC 60034-7:1992 + A1:2000) Machines lectriques tournantes Partie 7: Classification des modes de construction, des dispositions de montage et position de la bote bornes (Code IM) (inclut lamendement A1:2
14、001) (CEI 60034-7:1992 + A1:2000) Drehende elektrische Maschinen Teil 7: Klassifizierung der Bauarten, der Aufstellungsarten und der Klemmkasten-Lage (IM-Code) (enthlt Anderung A1:2001) (IEC 60034-7:1992 + A1:2000) This European Standard was approved by CENELEC on 1992-03-24. Amendment A1 was approv
15、ed by CENELEC on 2000-11-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nation
16、al standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language
17、and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switze
18、rland and United Kingdom. CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B-1050 Brussels 1993 Copyright reserved to CENELEC members Ref. No. EN 6
19、0034-7:1993 + A1:2001 EEN 60034-7:1993 BSI 5 October 2001 2 Foreword The text of document 2H(CO)29, as prepared by subcommittee 2H: Degrees of protection, methods of cooling and mounting arrangements, of IEC technical committee 2: Rotating machinery, was submitted to the IEC-CENELEC parallel vote in
20、 July 1991. The reference document was approved by CENELEC as EN 60034-7 on 24 March 1992. The following dates were fixed: Foreword to amendment A1 The text of document 2/1095/FDIS, future amendment 1 to IEC 60034-7:1992, prepared by IEC TC 2, Rotating machinery, was submitted to the IEC-CENELEC par
21、allel vote and was approved by CENELEC as amendment A1 to EN 60034-7:1993 on 2000-11-01. The following dates were fixed: Contents Page Foreword 2 Section 1. Scope and definitions 1.1 Scope 3 1.2 Definitions 3 Section 2. Code I (Alpha-numeric designation) 2.1 Designation of machines with horizontal s
22、hafts 5 2.2 Designation of machines with vertical shafts 8 2.3 Terminal box location 11 Section 3. Code II (All-numeric designation) 3.1 Designation 13 3.2 Significance of the first numeral 13 3.3 Significance of the fourth numeral 13 3.4 Significance of the second and third numerals 13 3.5 Terminal
23、 box location 14 3.6 Examples of designations 14 Annex A (informative) Relationship between Code I and Code II 24 Table 1 Designations for machines with horizontal shafts (IM B) 6 Table 2 Designations for machines with vertical shafts (IM V) 8 Table 3 Significance of the first numeral 13 Table 4 Sig
24、nificance of the fourth numeral 13 Table 5 Significance of second and third numerals for first numeral 1 15 Table 6 Significance of second and third numerals for first numeral 2 16 Table 7 Significance of second and third numerals for first numeral 3 17 Table 8 Significance of second and third numer
25、als for first numeral 4 18 Table 9 Significance of second and third numerals for first numeral 5 19 Table 10 Significance of second and third numerals for first numeral 6 20 Table 11 Significance of second and third numerals for first numeral 7 21 Table 12 Significance of second and third numerals f
26、or first numeral 8 22 Table 13 Significance of second and third numerals for first numeral 9 23 latest date of publication of an identical national standard (dop) 1993-12-01 latest date of withdrawal of conflicting national standards (dow) 1993-12-01 latest date by which the amendment has to be impl
27、emented at national level by publication of an identical national standard or by endorsement (dop) 2001-08-01 latest date by which the national standards conflicting with the amendment have to be withdrawn (dow) 2003-11-01EN 60034-7:1993 BSI 5 October 2001 3 Section 1. Scope and definitions 1 1.1 Sc
28、ope This part of IEC 34 specifies the IM code, a classification of types of construction and mounting arrangements of rotating electrical machines. Two systems of classification are provided as follows: The type of machine not covered by Code II should be fully described in words. The relationship b
29、etween Code I and Code II is given in Annex A. 1.2 Definitions For the purposes of this part of IEC 34, the following definitions apply: 1.2.1 type of construction the arrangement of machine components with regard to fixings, bearing arrangement and shaft extension (IEV 411-13-34) 1) 1.2.2 mounting
30、arrangement the orientation on site of the machine as the whole with regard to shaft alignment and position of fixings (IEV 411-13-35) 1.2.3 shaft extension a portion of a shaft extending beyond an extreme bearing (IEV 411-13-07) NOTE The bearing may be on the machine itself or be part of an assembl
31、y comprising a machine and (an) additional bearing(s). 1.2.4 drive-end of a machine (D-end) that end of the machine which accommodates the shaft end (IEV 411-13-36) NOTE This is normally the driving end of a motor or the driven end of a generator. Where for some machines the above definition is inad
32、equate, the D-end is defined as follows: a) machine with two shaft extensions of different diameter: the end with the larger shaft diameter; b) machine with a cylindrical shaft extension and a conical shaft extension of the same diameter: the end with cylindrical shaft extension; c) machine with oth
33、er arrangements: according to IEC 34-8 if applicable; otherwise by agreement. NOTE The outer diameter of a forged-on flange is taken to be the diameter of the shaft extension. 1.2.5 non-drive end of the machine (N-end) that end of the machine opposite to the drive end (IEV 411-13-37) Code I (see sec
34、tion 2): An alpha-numeric designation applicable to machines with endshield bearing(s) and only one shaft extension. Code II (see section 3): An all-numeric designation applicable to a wider range of types of machines including types covered by Code I. 1) IEC 50 (411):1973, International Electrotech
35、nical Vocabulary (IEV), Chapter 411: Rotating machines.4 blankEN 60034-7:1993 BSI 5 October 2001 5 Section 2. Code I (Alpha-numeric designation) 2 2.1 Designation of machines with horizontal shafts In Code I, a machine with a horizontal shaft is designated by the Code letters IM (International Mount
36、ing), followed by a space, the letter B and one or two numerals, as shown in Table 1.EN 60034-7:1993 6 BSI 5 October 2001 Section 2 Table 1 Designations for machines with horizontal shafts (IM B)EN 60034-7:1993 BSI 5 October 2001 7 Section 2 Table 1 Designations for machines with horizontal shafts (
37、IM B) (concluded)EN 60034-7:1993 8 BSI 5 October 2001 Section 2 2.2 Designation of machines with vertical shafts In Code I, a machine with a vertical shaft is designated by the Code letters IM (International Mounting) followed by a space, the letter V and one or two numerals, as shown in Table 2. Ta
38、ble 2 Designations for machines with vertical shafts (IM V)EN 60034-7:1993 BSI 5 October 2001 9 Section 2EN 60034-7:1993 10 BSI 5 October 2001 Section 2EN 60034-7:1993 BSI 5 October 2001 11 Section 2 2.3 Terminal box location When designated, the terminal box position shall be coded with a final let
39、ter in accordance with the following rules: a) machines with feet shall be viewed from the D-end with the feet at 6 oclock; b) machines with flange only and with drains shall be viewed from the D-end and with the drains at 6 oclock; c) other configurations shall not have a coding. The coding shall c
40、onform to the following table: Letter designation Terminal box location R Right 3 oclock B Bottom 6 oclock L Left 9 oclock T Top 12 oclock None Unspecified12 blankEN 60034-7:1993 BSI 5 October 2001 13 Section 3. Code II (All-numeric designation) 3 3.1 Designation In Code II, a machine is designated
41、by the Code letters IM (International Mounting) followed by a space and four numerals. The first, second and third numerals designate aspects of construction (see 3.2 and 3.4). The fourth numeral designates the type of shaft extension (see 3.3). When used, a letter following the four numerals shall
42、designate the terminal box position, see 3.5. 3.2 Significance of the first numeral The significance of the first numeral is given in Table 3 below. Table 3 Significance of the first numeral 3.3 Significance of the fourth numeral The significance of the fourth numeral is given in Table 4 below. Tabl
43、e 4 Significance of the fourth numeral 3.4 Significance of the second and third numerals The significance of the second and third numerals is specified in Table 5, Table 6, Table 7, Table 8, Table 9, Table 10, Table 11, Table 12 and Table 13 depending on the first numeral with which they are associa
44、ted (see Table 3). First numeral Significance Table relevant to the second and third numerals 0 1 2 3 4 5 6 7 8 9 Not allocated Foot-mounted machines with endshield bearing(s) only Foot-and-flange-mounted machines with endshield bearing(s) only Flange-mounted machines with endshield bearing(s) only,
45、 with a flange part of an endshield Flange-mounted machines with endshield bearing(s) only, with a flange not part of an endshield but an integral part of the frame or other component Machines without bearings Machines with endshield bearing(s) and pedestal bearing(s) Machines with pedestal bearing(
46、s) only Vertical machines of construction not covered by first numerals 1 to 4 Machines with special mounting arrangements 5 6 7 8 9 10 11 12 13 Fourth numeral Significance 0 1 2 3 4 5 6 7 8 9 No shaft extension One cylindrical shaft extension Two cylindrical shaft extensions One conical shaft exten
47、sion Two conical shaft extensions One flanged shaft extension Two flanged shaft extensions Flanged shaft extension (D-end) and cylindrical shaft extension (N-end) (Not allocated) Other arrangementEN 60034-7:1993 14 BSI 5 October 2001 Section 3 3.5 Terminal box location When designated, the terminal
48、box position shall be coded with a final letter in accordance with the following rules: a) machines with feet shall be viewed from the D-end with the feet at 6 oclock; b ) m a c h i n e s w i t h f l a n g e o nl y a n d w i t h dr a i n s s h a l l b e v i e w e d fr o m t h e D - e n d a n d w i t
49、 h t h e d ra i n s at 6 oclock; c) other configurations shall not have a coding. The coding shall conform to the following table: 3.6 Examples of designations In Table 5 to Table 13 common types of construction and mounting arrangements are illustrated by sketches, and their designations are given using a particular fourth numeral. Other fourth numerals could be applicable (see Table 4). The absence of a sketch does not imply tha
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1