BS EN 60169-24-1994 Radio-frequency connectors - Radio-frequency coaxial connectors with screw coupling typically for use in 75 ohm cable distribution systems (Type F)《射频连接器 带螺旋耦合器.pdf

1、BRITISH STANDARD BS EN 60169-24:1994 IEC 169-24: 1991 Radio-frequency connectors Part 24: Radio-frequency coaxial connectors with screw coupling, typically for use in75ohm cable distribution systems (Type F) The European Standard EN 60169-24:1993 has the status of a British Standard UDC 621.316.541.

2、029.51.7BSEN60169-24:1994 This British Standard, having been prepared under the directionof the Electronic Components Standards Policy Committee, was published underthe authority of the Standards Board and comes into effect on 15March1994 BSI 09-1999 The following BSI references relate to the work o

3、n this standard: Committee reference ECL/6 Draft announced in BSI News, January1994 ISBN 0 580 22838 X Cooperating organizations The European Committee for Electrotechnical Standardization (CENELEC), under whose supervision this European Standard was prepared, comprises the national committees of th

4、e following countries: Austria Italy Belgium Luxembourg Denmark Netherlands Finland Norway France Portugal Germany Spain Greece Sweden Iceland Switzerland Ireland United Kingdom Amendments issued since publication Amd. No. Date CommentsBSEN60169-24:1994 BSI 09-1999 i Contents Page Cooperating organi

5、zations Inside front cover National foreword ii Foreword 2 Text of EN 60169-24 3 National annex NA (informative) Committees responsible Inside back coverBSEN60169-24:1994 ii BSI 09-1999 National foreword This British Standard has been prepared under the direction of the Electronic Components Standar

6、ds Policy Committee, and is the English language version of EN60169-24:1993 Radio-frequency connectors Part 24: Radio-frequency coaxial connectors with screw coupling, typically for use in75ohm cable distribution systems (Type F), published by the European Committee for Electrotechnical Standardizat

7、ion (CENELEC). It is identical with IEC169-24:1991 published by the International Electronic Components Electrotechnical Committee (IEC). A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct applicatio

8、n. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, theEN title page, pages2 to 4, an inside back cover and a back cover. This standard has been updated (see co

9、pyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover.EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 60169-24 September 1993 UDC 621.316.541.029.5/.7 Descriptors: Radio-frequency connectors coaxial with screw coupling, t

10、ype F English version Radio-frequency connectors Part 24: Radio-frequency coaxial connectors with screw coupling, typically for use in75ohm cable distribution systems (Type F) (IEC 169-24:1991) Connecteurs pour frquences radiolectriques Vingt-quatrime partie: Connecteurs coaxiaux pour frquences radi

11、olectriques avec verrouillage vis pour usage dans les systmesde distribution par cbles 75 ohms (type F) (CEI 169-24:1991) Hochfrequenz-Steckverbindungen Teil24:Hochfrequenz-Koaxial-Steckverbinder mit Schraubkupplung (Typ F), vorzugsweise fr den Einsatz in 75-Ohm Kabelverteilnetzen (IEC 169-24:1991)

12、This European Standard was approved by CENELEC on1993-07-06. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical r

13、eferences concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENEL

14、EC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway,

15、 Portugal, Spain, Sweden, Switzerland and UnitedKingdom. CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B-1050 Brussels 1993 Copyright reserved t

16、o CENELEC members Ref. No. EN 60169-24:1993 EEN60169-24:1993 BSI 09-1999 2 Foreword The CENELEC questionnaire procedure, performed for finding out whether or not the International Standard IEC169-24:1991 could be accepted without textual changes, has shown that no common modifications were necessary

17、 for the acceptance as European Standard. The reference document was submitted to the CENELEC members for formal vote and was approved by CENELEC as EN60169-24 on6July1993. The following dates were fixed: For products which have complied with the relevant national standard before1994-08-01, as shown

18、 by the manufacturer or by a certification body, this previous standard may continue to apply for production until1999-08-01. The following publication is quoted in this standard: ISO 370:1975, Toleranced dimensions Conversion from inches into millimetres and vice versa. Contents Page Foreword 2 1 S

19、cope 3 2 IEC type designation 3 3 Description of connectors 3 4 Dimensions Mating face details 3 Figure 1 Connector with pin center contact 3 Figure 2 Connector with socket center contact 4 Table 1 Dimensions 4 latest date of publication of an identical national standard (dop) 1994-08-01 latest date

20、 of withdrawal of conflicting national standards (dow) 1994-08-01EN60169-24:1993 BSI 09-1999 3 1 Scope This standard specifies radio-frequency coaxial connectors which are typically for use in757 cable distribution systems with a variety of flexible cables, but which may also be used in both matched

21、 and unmatched applications. These connectors are in general intended for permanent mounting and for use with infrequent engagement and separation. This standard only specifies interface dimensions. 2 IEC type designation Connectors conforming to this standard shall be designated by reference to thi

22、s standard. 3 Description of connectors This type of connector has screw locking with a3/8-32 UNEF-2“B” thread. Normally, the plug will be a free connector, the socket a fixed connector. The design of the plug may be either such that the inner conductor of the cable serves as the male contact, or su

23、ch that the centre (male) contact is independent of the cable inner conductor. The female contact in the socket shall accept male contacts with a diameter range of0,51mm to1,63mm(0,020in to0,064in). The inner diameter of the tubular part of the plug is in principle appropriate for cables with diamet

24、ers over dielectric of3,71mm(0,146in); for larger cables, adaptations are necessary. NOTE 1Caution: Care should be taken when replacing larger diameter pin contacts(1,63mm/0,064in) with those having a smaller diameter(0,51mm/0,020in) due to potential mechanical deformation in the socket. NOTE 2It is

25、 important that the center female contact operate effectively over the full range of indicated conductor diameters. A gauging procedure to prove this performance is under consideration. 4 Dimensions Mating face details Inch dimensions are original dimensions. The millimetre dimensions are derived fr

26、om original inch dimensions according to ISO Standard370. Figure 1 Connector with pin center contact (for dimensions, seeTable 1)EN60169-24:1993 4 BSI 09-1999 Table 1 Dimensions Figure 2 Connector with socket center contact (for dimensions, seeTable 1) Reference Millimetres (mm) Inches (in) Note Min

27、. Max. Min. Max. a 4,95 6,86 0,195 0,270 b 7,29 0,287 c 0,25 0,010 1 d 0,51 1,63 0,020 0,064 e 12,95 0,510 2/dia. f 3,8 0,149 3/dia. g 6/dia. h 3,86 0,152 dia. i 0,30 0,012 j 5,56 0,219 4 k 7,0 0,273 l 7,59 0,299 m 4,70 0,185 NOTE 1Protrusion of dielectric beyond reference plane is applicable to onl

28、y the0,146in nominal dielectric core diameter cables. When larger core diameter cables are used, no protrusion of the dielectric beyond the reference plane is permitted. NOTE 2Shape of coupling nut is optional; however, provision for wrench fighting should be made. For example, wrench flats. NOTE 3A

29、pplicable to only the0,146in nominal dielectric core diameter cables. The3,8mm maximum diameter is not applicable when larger core diameter cables are used. NOTE 4Length of full thread. NOTE 5Shape of connector body is optional; however, provision for wrench tightening should be made. For example: w

30、rench flats. NOTE 6Socket contact shall accept a pin contact of0,51mm to1,63mm(0,020in to0,064in); this shall be satisfied at dimensionm.BSEN60169-24:1994 BSI 09-1999 National annex NA (informative) Committees responsible The UnitedKingdom participation in the preparation of this European Standard w

31、as entrusted by the Electronic Components Standards Policy Committee (ECL/-) to Technical Committee ECL/6, upon which the following bodies were represented: British Cable Makers Confederation British Telecommunications plc EEA (the Association of Electronics, Telecommunications and Business Equipmen

32、t Industries) National Supervising Inspectorate Society of British Aerospace Companies Limited Telecommunications Cables Group of Bcmc The following bodies were also represented in the drafting of the standard, through subcommittees and panels: AEA Technology Beccama (Beama Electrical Cable Connecto

33、r and Accessories Manufacturers Association) Electronic Components Industry Federation Ministry of Defence Society of Cable Television EngineersBS EN 60169-24:1994 IEC 169-24: 1991 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsibl

34、e for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or

35、 editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found on th

36、e inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be

37、 addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide rang

38、e of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax

39、:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in

40、all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means

41、electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.