BS EN 60264-2-1-1992 Packaging for winding wires - Cylindrical barrelled delivery spools - Basic dimensions《绕组线的封装 圆桶形输出线轴 基本尺寸》.pdf

1、BRITISH STANDARD BS EN 60264-2-1:1996 IEC 264-2-1: 1989 Incorporating Amendment No. 1 BS 7584-2.1:1992 renumbered and Amendment No. 2 Packaging of winding wires Part 2: Cylindrical barrelled delivery spools Section 2.1 Basic dimensions The European Standard EN 60264-2-1:1994, incorporating amendment

2、 A1:2003, has the status of a British Standard ICS 29.060.10 BS EN 60264-2-1:1996 This British Standard, having been prepared under the direction of the Cables and Insulation Standards Policy Committee, was published under the authority of the Standards Board and comes into effect on 15 August 1992

3、BSI 26 November 2003 The following BSI references relate to the work on this British Standard: Committee reference CIL/55 Draft announced in BSI News May 1992 ISBN 0 580 21023 5 Committees responsible for this British Standard The preparation of this British Standard was entrusted by the Cables and

4、Insulation Standards Policy Committee (CIL/-) to Technical Committee CIL/55, upon which the following bodies were represented: British Cable Makers Confederation British Non-ferrous Metals Federation British Railways Board Covered Conductors Association EEA (the Association of Electronics, Telecommu

5、nications and Business Equipment Industries) Electrical and Electronic Insulation Association Electronic Components Industry Federation Transmission and Distribution Association (BEAMA Ltd.) Amendments issued since publication Amd. No. Date Comments 9048 May 1996 14833 26 November 2003 Replacement o

6、f Table 1 and Figure 1BS EN 60264-2-1:1996 BSI 26 November 2003 i Contents Page Committees responsible Inside front cover National foreword ii 1S c o p e 3 2O b j e c t 3 3D i m e n s i o n s 3 4M a t e r i a l 3 Annex ZA (normative) Other international publications quoted in this standard with the

7、references of the relevant European publications 5 Figure 1 Cylindrical barrelled delivery spools 4 Table 1 Dimensions and tolerances for cylindrical barrelled delivery spools 3 BS EN 60264-2-1:1996 ii BSI 26 November 2003 National foreword This British Standard has been prepared by Technical Commit

8、tee GEL/55 (formerly CIL/55) and is the English language version of EN 60264-2-1:1994 Packaging of winding wires Part 2: Cylindrical barrelled delivery spools Section 1: Basic dimensions, including amendment A1:2003, published by the European Committee for Electrotechnical Standardization (CENELEC).

9、 It is identical with IEC 264-2-1:1989, including amendment 1:2003, published by the International Electrotechnical Commission (IEC). BS EN 60264, of which there are four Parts, deals with the packaging of winding wires. Part 1 covers containers, Part 2 covers cylindrical barrelled delivery spools,

10、Part 3 covers taper barrelled delivery spools and Part 4 covers methods of test. This British Standard is one of a series dealing with insulated wires used for windings in electrical equipment, which comprises the following three groups. IEC 851, Methods of test for winding wires; IEC 317, Specifica

11、tions for particular types of winding wires; IEC 264, Packaging of wires. NOTE BS 6811 Winding wires Part 0:1993 General introduction and list of Parts lists the various Sections of BS 6811 and BS 7584 against the corresponding Parts of the IEC standards listed above. Some or all of these IEC standa

12、rds will be adopted as BS ENs in due course and the relevant Parts of BS 6811 and BS 7584 will be renumbered as BS ENs. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does

13、not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, the EN title page, pages 2 to 5 and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued.EUROP

14、EAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 60264-2-1 December 1994 + A1 October 2003 ICS 29.060.10 English version P a c k a g i n g o f w i n d i n g w i r e s P a r t 2 : C y l i n d r i c a l b a r r e l l e d d e l i v e r y s p o o l s Section 1: Basic dimensions (includes amendment A1:200

15、3) (IEC 60264-2-1:1989/A1:2003) Conditionnement des fils de bobinage Partie 2: Bobines de livraison ft de forme cylindrique S e c t i o n 1 : D i m e n s i o n s d e b a s e (inclut lamendement A1:2003) (CEI 60264-2-1:1989) Verpackung von Wickeldrhten Teil 2: Lieferspulen mit zylindrischem Kern Haup

16、tabschnitt 1: Mae (enthlt nderung A1:2003) (IEC 60264-2-1:1989) This European Standard was approved by CENELEC on 1994-09-01. Amendment A1 was approved by CENELEC on 2003-10-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving th

17、is European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versio

18、ns (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of A

19、ustria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Lithuania, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and United Kingdom. CENELEC European Committee for Electrotechnical Standardization Comit Eu

20、ropen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B-1050 Brussels 2003 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC members Ref. No. EN 60264-2-1:1994 + A1:2003 EEN 60264

21、-2-1:1994 BSI 26 November 2003 2 Foreword The text of the International Standard IEC 264-2-1:1989, prepared by IEC TC 55, Winding wires, was approved by CENELEC as HD 46.2.1 S1 on 1990-05-01. This Harmonization Document was submitted to the formal vote for conversion into a European Standard and was

22、 approved by CENELEC as EN 60264-2-1 on 1994-09-01. The following date was fixed: Annexes designated “normative” are part of the body of the standard. In this standard, Annex ZA is normative. Annex ZA has been added by CENELEC. Foreword to amendment A1 The text of document 55/830/FDIS, future amendm

23、ent 1 to IEC 60264-2-1:1989, prepared by IEC TC 55, Winding wires, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as amendment A1 to EN 60264-2-1:1994 on 2003-10-01. The following dates were fixed: latest date by which the EN has to be implemented at national level by pub

24、lication of an identical national standard or by endorsement (dop) 1995-10-15 latest date by which the amendment has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2004-07-01 latest date by which the national standards conflicting with th

25、e amendment have to be withdrawn (dow) 2006-10-01EN 60264-2-1:1994 BSI 26 November 2003 3 1 Scope This standard specifies the basic dimensions for cylindrical barrelled delivery spools for winding wires. 2 Object To standardize the dimensions of cylindrical barrelled delivery spools. 3 Dimensions Th

26、e dimensions and tolerances for cylindrical barrelled delivery spools are given in Table 1 in accordance with Figure 1. NOTE Figure 1 is given to identify the dimensions specified and is not intended to show any particular construction. Table 1 Dimensions and tolerances for cylindrical barrelled del

27、ivery spools 4 Material Requirements are to be stated in the purchasers order. Spool type Dimensions mm d 1 d 2 d 3 b d 4 d 5 c d 6 a L 1 l 2 a a l 1 zye 1 r Nom. Tol. Nom. Tol. Min.40 40 25 11 +0,15 15 1.5 50 38 0,10 0,75 14 0,4 0,08 150 50 32 11 +0,15 15 1.5 50 38 0,15 0,75 16 0,4 0,10 163 63 40 1

28、1 +0,15 15 2 63 49 0,15 1,0 18 0,4 0,15 1,680 80 50 16 +0,20 24 7 2 80 64 0,15 1,0 20 0,6 0,15 20 2100 100 63 16 +0,20 24 7 2 100 80 0,20 1,0 22 0,6 0,20 20 2125 125 80 16 +0,20 24 7 3 125 100 0,20 1,5 25 0,6 0,20 20 3160 160 100 22 +0,20 34 13 3 160 128 0,20 1,5 28 0,6 0,30 32 3200 200 125 22 +0,20

29、 34 13 3 200 160 0,30 1,5 32 0,6 0,30 32 4250 250 160 22 +0,20 34 13 4 200 160 0,40 2,0 36 1,0 0,40 32 5355 355 224 36 +0,50 60 26 5 200 160 0,40 2.5 40 1,2 0,5 80 5500 500 315 36 +0,50 60 26 10 250 180 0,50 5.0 40 1,6 0.7 80 5710 710 500 51 +0,50 80 26 15 250 180 0,80 7.5 45 2,0 1.0 140 6 1 000 1 0

30、00 800 51 +0,50 80 26 26 250 180 1,00 13 50 3,0 1.5 140 6 aSpools without holes can be ordered if agreed between supplier and purchaser. If bore d 6is wanted, quantity and position of bore d 6shall be according to agreement. bFor spool types 250 and 710, a central bore diameter d 3of (36 mm) may be

31、used if agreed between supplier and purchaser. cNumber of bore d 5for spools K 80 and K 100: minimum 1 bore per side. Number of bore d 5for spools from K 125: minimum 2 bore per side. For spools K 80 and K 100 the bore d 5can be designed as a blind hole. +0,5 0EN 60264-2-1:1994 4 BSI 26 November 200

32、3 Figure 1 Cylindrical barrelled delivery spoolsEN 60264-2-1:1994 BSI 26 November 2003 5 Annex ZA (normative) Other international publications quoted in this standard with the references of the relevant European publications This European Standard incorporates by dated or undated reference, provisio

33、ns from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by a

34、mendment or revision. For undated references the latest edition of the publication referred to applies. NOTE When the international publication has been modified by CENELEC common modifications, indicated by (mod), the relevant EN/HD applies. IEC publication Date Title EN/HD Date 182 Basic dimension

35、s of winding wires 264 series Packaging of winding wires EN 60264 series 317 series Specifications for particular types of winding wires HD 555 EN 60317 series series 851 series Methods of test for winding wires HD 490 EN 60851 series seriesBS EN 60264-2-1:1996 IEC 264-2-1: 1989 BSI 389 Chiswick Hig

36、h Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amen

37、dment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard w

38、ould inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the l

39、atest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-. In

40、response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards th

41、rough its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-. Subscribing members

42、of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-. Information regarding onl

43、ine access to British Standards via British Standards Online can be found at http:/www.bsi- Further information about BSI is available on the BSI website at http:/www.bsi-. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the inter

44、national standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. Thi

45、s does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.