BS EN 60317-22-2004+A1-2010 Specifications for particular types of winding wires - Polyester or polyesterimide enamelled round copper wire overcoated with polyamide class 180《特种绕组线.pdf

1、BRITISH STANDARD BS EN 60317-22:2004 Specifications for particular types of winding wires Part 22: Polyester or polyesterimide enamelled round copper wire overcoated with polyamide, class 180 ICS 26.060.10 +A1:2010 Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 06/08/2010 04:11, Uncontrolled

2、 Copy, (c) BSINational foreword This British Standard is the UK implementation of EN 60317-22:2004+A1:2010. It is identical to IEC 60317-22:2004, incorporating amendment 1:2009. It supersedes BS EN 60317-22:2004 which is withdrawn. The UK participation in its preparation was entrusted to Technical C

3、ommittee GEL/55, Winding wires. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Sta

4、ndard cannot confer immunity from legal obligations. BS EN 60317-22:2004+A1:2010 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 13 December 2004 BSI 2010 Amendments/corrigenda issued since publication Date Comments 30 April 2010 Implementati

5、on of IEC amendment 1:2009 with CENELEC endorsement A1:2010; Text of Clause 23 replaced ISBN 978 0 580 67181 4 Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 06/08/2010 04:11, Uncontrolled Copy, (c) BSIEUROPEAN STANDARD EN 60317-22:2004+A1 NORME EUROPENNE EUROPISCHE NORM February 2010 CENELE

6、C European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B - 1050 Brussels 2004 CENELEC - All rights of exploitation in any form and by any means reserved worldw

7、ide for CENELEC members. Ref. No. EN 60317-22:2004 E ICS 26.060.10 Supersedes EN 60317-22:1995 + A1:1998English version Specifications for particular types of winding wires Part 22 : Polyester or polyesterimide enamelled round copper wire overcoated with polyamide, class 180 (IEC 60317-22:2004)Spcif

8、ications pour types particuliers de fils de bobinage Partie 22: Fil de section circulaire en cuivre maill avec polyester ou polyesterimide et avec surcouche polyamide, classe 180 (CEI 60317-22:2004) Technische Lieferbedingungen fr bestimmte Typen von Wickeldrhten Teil 22: Runddrhte aus Kupfer, lacki

9、soliert mit Polyester oder Polyesterimid und darber mit Polyamid, Klasse 180 (IEC 60317-22:2004) This European Standard was approved by CENELEC on 2004-09-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standar

10、d the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French

11、, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Cy

12、prus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STAN

13、DARDS, 06/08/2010 04:11, Uncontrolled Copy, (c) BSIForeword The text of document 55/910/FDIS, future edition 3 of IEC 60317-22, prepared by IEC TC 55, Winding wires, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 60317-22 on 2004-09-01. This European Standard supers

14、edes EN 60317-22:1995 + A1:1998. The main changes with respect to EN 60317-22:1995 are as follows: new requirements for appearance, Subclause 3.2, added; breakdown voltage values, former Table 3, replaced with a reference to EN 60317-0-1; new pin hole test, Clause 23, added. The following dates were

15、 fixed: latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2005-06-01 latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 2007-09-01 Annex ZA has been added by CENELEC

16、. _ Endorsement notice The text of the International Standard IEC 60317-22:2004 was approved by CENELEC as a European Standard without any modification. _ Foreword to amendment A1 The text of document 55/1124/CDV, future amendment 1 to IEC 60317-22:2004, prepared by IEC TC 55, Winding wires, was sub

17、mitted to the IEC-CENELEC parallel vote and was approved by CENELEC as amendment A1 to EN 60317-22:2004 on 2010-02-01. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and CENELEC shall not be held responsible for identifying a

18、ny or all such patent rights. The following dates were fixed: latest date by which the amendment has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2010-11-01 latest date by which the national standards conflicting with the amendment have

19、 to be withdrawn (dow) 2013-02-01 _ Endorsement notice The text of amendment 1:2009 to the International Standard IEC 60317-22:2004 was approved by CENELEC as an amendment to the European Standard without any modification. _ BS EN 60317-22:2004+A1:2010 EN 60317-22:2004+A1:2010 (E) Page 2 Licensed Co

20、py: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 06/08/2010 04:11, Uncontrolled Copy, (c) BSI CONTENTS INTRODUCTION.4 1 Scope.5 2 Normative references .5 3 Definitions and general notes on methods of test and appearance5 3.1 Definitions and general notes on methods of test 5 3.2 Appearance.6 4 Dimensions

21、 6 5 Electrical resistance .6 6 Elongation 6 7 Springiness 6 8 Flexibility and adherence6 9 Heat shock .6 10 Cut-through 6 11 Resistance to abrasion (nominal conductor diameters from 0,250 mm up to and including 2,500 mm) .6 12 Resistance to solvents7 13 Breakdown voltage .7 14 Continuity of insulat

22、ion .7 15 Temperature index .7 16 Resistance to refrigerants.8 17 Solderability .8 18 Heat or solvent bonding8 19 Dielectric dissipation factor.8 20 Resistance to transformer oil8 21 Loss of mass 8 23 Pin hole test .8 30 Packaging 8 Table 1 Resistance to abrasion7 Annex ZA (normative) Normative refe

23、rences to international publications with their corresponding European publications .9 BS EN 60317-22:2004+A1:2010 EN 60317-22:2004+A1:2010 (E) Page 3 Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 06/08/2010 04:11, Uncontrolled Copy, (c) BSI INTRODUCTION This part of IEC 60317 is one of a s

24、eries which deals with insulated wires used for windings in electrical equipment. The series has three groups describing 1) winding wires Test methods (IEC 60851); 2) specifications for particular types of winding wires (IEC 60317); 3) packaging of winding wires (IEC 60264). BS EN 60317-22:2004+A1:2

25、010 EN 60317-22:2004+A1:2010 (E) Page 4 Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 06/08/2010 04:11, Uncontrolled Copy, (c) BSI SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES Part 22: Polyester or polyesterimide enamelled round copper wire overcoated with polyamide, class 180 1 Sco

26、pe This part of IEC 60317 specifies the requirements of enamelled round copper winding wire of class 180 with a dual coating. The underlying coating is based on polyester or polyesterimide resin, which may be modified providing it retains the chemical identity of the original resin and meets all spe

27、cified wire requirements. The superimposed coating is based on polyamide resin. NOTE A modified resin is a resin that has undergone a chemical change, or contains one or more additives to enhance certain performance or application characteristics. Class 180 is a thermal class that requires a minimum

28、 temperature index of 180 and a heat shock temperature of at least 200 C. The temperature in degrees Celsius corresponding to the temperature index is not necessarily that at which it is recommended that the wire be operated and this will depend on many factors, including the type of equipment invol

29、ved. The range of nominal conductor diameters covered by this standard is as follows: grade 1: 0,050 mm up to and including 3,150 mm; grade 2: 0,050 mm up to and including 5,000 mm; grade 3: 0,250 mm up to and including 1,600 mm. The nominal conductor diameters are specified in Clause 4 of IEC 60317

30、-0-1. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60317-0-1, Speci

31、fications for particular types of winding wires Part 0: General requirements Section 1: Enamelled round copper wire 3 Definitions and general notes on methods of test and appearance 3.1 Definitions and general notes on methods of test For definitions and general notes on methods of test, see Clause

32、3 of IEC 60317-0-1. In case of inconsistencies between IEC 60317-0-1 and this standard, IEC 60317-22 shall prevail. BS EN 60317-22:2004+A1:2010 EN 60317-22:2004+A1:2010 (E) Page 5 Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 06/08/2010 04:11, Uncontrolled Copy, (c) BSI 3.2 Appearance See C

33、lause 3 of IEC 60317-0-1. 4 Dimensions See Clause 4 of IEC 60317-0-1. 5 Electrical resistance See Clause 5 of IEC 60317-0-1. 6 Elongation See Clause 6 of IEC 60317-0-1. 7 Springiness See Clause 7 of IEC 60317-0-1. 8 Flexibility and adherence See Clause 8 of IEC 60317-0-1, where the constant K used f

34、or the calculation of the number of revolutions for the peel test shall be 110 mm. 9 Heat shock See Clause 9 of IEC 60317-0-1, where the minimum heat shock temperature shall be 200 C. 10 Cut-through No failure shall occur within 2 min at 265 C. 11 Resistance to abrasion (nominal conductor diameters

35、from 0,250 mm up to and including 2,500 mm) The wire shall meet the requirements given in Table 1. BS EN 60317-22:2004+A1:2010 EN 60317-22:2004+A1:2010 (E) Page 6 Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 06/08/2010 04:11, Uncontrolled Copy, (c) BSI Table 1 Resistance to abrasion Grade

36、1 Grade 2 Grade 3 Nominal conductor diameter mm Minimum average force to failure N Minimum force to failure of each measurement N Minimum average force to failure N Minimum force to failure of each measurement N Minimum average force to failure N Minimum force to failure of each measurement N 0,250

37、0,280 0,315 0,355 0,400 2,85 3,10 3,35 3,60 3,85 2,45 2,60 2,80 3,05 3,25 4,70 5,05 5,45 5,85 6,25 4,00 4,30 4,60 4,95 5,30 5,80 6,25 6,70 7,20 7,70 4,90 5,30 5,70 6,10 6,50 0,450 0,500 0,560 0,630 0,710 4,15 4,45 4,75 5,10 5,45 3,50 3,75 4,05 4,35 4,65 6,75 7,20 7,70 8,25 8,85 5,70 6,10 6,50 7,00 7

38、,50 8,25 8,85 9,50 10,20 10,90 7,00 7,50 8,05 8,65 9,25 0,800 0,900 1,000 1,120 1,250 5,85 6,30 6,75 7,35 7,90 4,95 5,35 5,75 6,20 6,70 9,50 10,20 10,90 11,60 12,50 8,05 8,60 9,20 9,80 10,50 11,70 12,50 13,30 14,20 15,20 9,90 10,60 11,30 12,00 12,90 1,400 1,600 1,800 2,000 2,240 8,50 9,20 9,95 10,60

39、 11,70 7,20 7,80 8,40 9,00 9,90 13,30 14,30 15,40 16,40 17,50 11,30 12,10 13,00 13,90 14,80 16,40 17,60 13,90 14,90 2,500 12,80 10,80 18,60 15,80 For intermediate nominal conductor diameters, the value of the next larger nominal conductor diameter shall be taken. 12 Resistance to solvents See Clause

40、 12 of IEC 60317-0-1. 13 Breakdown voltage See Clause 13 of IEC 60317-0-1, where the elevated temperature shall be 180 C. 14 Continuity of insulation See Clause 14 of IEC 60317-0-1. 15 Temperature index See Clause 15 of IEC 60317-0-1, where the minimum temperature index shall be 180. BS EN 60317-22:

41、2004+A1:2010 EN 60317-22:2004+A1:2010 (E) Page 7 Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 06/08/2010 04:11, Uncontrolled Copy, (c) BSI 16 Resistance to refrigerants Test inappropriate. 17 Solderability Test inappropriate. 18 Heat or solvent bonding Test inappropriate. 19 Dielectric dis

42、sipation factor Test inappropriate. 20 Resistance to transformer oil Test inappropriate. 21 Loss of mass Test inappropriate. 23 Pin hole test 30 Packaging See Clause 30 of IEC 60317-0-1. _ See Clause 23 of IEC 60317-0-1. BS EN 60317-22:2004+A1:2010 EN 60317-22:2004+A1:2010 (E) Page 8 Licensed Copy:

43、Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 06/08/2010 04:11, Uncontrolled Copy, (c) BSI Annex ZA (normative) Normative references to international publications with their corresponding European publications The following referenced documents are indispensable for the application of this document. For d

44、ated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE Where an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. Publication Ye

45、ar Title EN/HD Year IEC 60317-0-1 - 1)Specifications for particular types of winding wires Part 0-1: General requirements - Enamelled round copper wire EN 60317-0-1 1998 2)1)Undated reference. 2)Valid edition at date of issue. BS EN 60317-22:2004+A1:2010 EN 60317-22:2004+A1:2010 (E) Page 9 Licensed

46、Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 06/08/2010 04:11, Uncontrolled Copy, (c) BSIBSI Group Headquarters 389 Chiswick High Road, London, W4 4AL, UK Tel +44 (0)20 8996 9001 Fax +44 (0)20 8996 7001 standards BSI - British Standards Institution BSI is the independent national body responsible

47、for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments o

48、r editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on

49、the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20