BS EN 60317-25-2010 Specifications for particular types of winding wires - Polyester or polyesterimide overcoated with polyamide-imide enamelled round aluminium wire class 200《特种绕组.pdf

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationSpecifications for particular types of winding wiresPart 25: Polyester or polyesterimide overcoated with polyamide-imide enamelled round aluminium wire, class 200BS EN 60317-25:2

2、010National forewordThis British Standard is the UK implementation of EN 60317-25:2010. It isidentical to IEC 60317-25:2010. It supersedes BS EN 60317-25:1997 which iswithdrawn.The UK participation in its preparation was entrusted to Technical CommitteeGEL/55, Winding wires.A list of organizations r

3、epresented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisions of acontract. Users are responsible for its correct application. BSI 2010ISBN 978 0 580 67182 1ICS 29.060.10Compliance with a British Standard cannot conf

4、er immunity fromlegal obligations.This British Standard was published under the authority of the StandardsPolicy and Strategy Committee on 30 June 2010.Amendments issued since publicationAmd. No. Date Text affectedBRITISH STANDARDBS EN 60317-25:2010EUROPEAN STANDARD EN 60317-25 NORME EUROPENNE EUROP

5、ISCHE NORM May 2010 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Management Centre: Avenue Marnix 17, B - 1000 Brussels 2010 CENELEC - All rights of exploitation in any form and by any

6、 means reserved worldwide for CENELEC members. Ref. No. EN 60317-25:2010 E ICS 29.060.10 Supersedes EN 60317-25:1996 + A1:1997 + A2:1998English version Specifications for particular types of winding wires - Part 25: Polyester or polyesterimide overcoated with polyamide-imide enamelled round aluminiu

7、m wire, class 200 (IEC 60317-25:2010) Spcifications pour types particuliers de fils de bobinage - Partie 25: Fil de section circulaire en aluminium maill avec polyester ou polyesterimide et avec surcouche polyamide-imide, classe 200 (CEI 60317-25:2010) Technische Lieferbedingungen fr bestimmte Typen

8、 von Wickeldrhten - Teil 25: Runddrhte aus Aluminium, lackisoliert mit Polyester oder Polyesterimid und darber mit Polyamidimid, Klasse 200 (IEC 60317-25:2010) This European Standard was approved by CENELEC on 2010-05-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations

9、which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This Europ

10、ean Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are t

11、he national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Sloven

12、ia, Spain, Sweden, Switzerland and the United Kingdom. BS EN 60317-25:2010EN 60317-25:2010 - 2 - Foreword The text of document 55/1181/FDIS, future edition 3 of IEC 60317-25, prepared by IEC TC 55, Winding wires, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 60317-

13、5 on 2010-05-01. This European Standard supersedes EN 60317-25:1996 + A1:1997 + A2:1998. The main changes with respect to EN 60317-25:1996 are listed below: Clause 3: addition of 3.3: Appearance; Clause 16: reference to the test for resistance to refrigerants in IEC 60851-4; Clause 22: deletion of t

14、he high temperature failure requirement; Clause 23: addition of pin hole test requirement. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and CENELEC shall not be held responsible for identifying any or all such patent rights

15、. The following dates were fixed: latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2011-02-01 latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 2013-05-01 Annex ZA

16、 has been added by CENELEC. _ Endorsement notice The text of the International Standard IEC 60317-25:2010 was approved by CENELEC as a European Standard without any modification. _ BS EN 60317-25:2010- 3 - EN 60317-25:2010 Annex ZA (normative) Normative references to international publications with

17、their corresponding European publications The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE Wh

18、en an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. Publication Year Title EN/HD Year IEC 60317-0-3 2008 Specifications for particular types of winding wires - Part 0-3: General requirements - Enamelled round aluminum wire EN 603

19、17-0-3 2008 IEC 60851-4 + A1 + A2 1996 1997 2005 Winding wires - Test methods - Part 4: Chemical properties EN 60851-4 + A1 + A2 1996 1997 2005 IEC 60851-5 2008 Winding wires - Test methods - Part 5: Electrical properties EN 60851-5 2008 BS EN 60317-25:2010 2 60317-25 IEC:2010 CONTENTS INTRODUCTION.

20、5 1 Scope.6 2 Normative references .6 3 Terms, definitions and general notes on methods of test and appearance 6 3.1 Terms and definitions 6 3.2 General notes on methods of test7 3.3 Appearance.7 4 Dimensions 7 5 Electrical resistance .7 6 Elongation 7 7 Springiness 7 8 Flexibility and adherence7 9

21、Heat shock .7 10 Cut-through 7 11 Resistance to abrasion (nominal conductor diameters up to and including 2,500 mm)7 12 Resistance to solvents8 13 Breakdown voltage .8 14 Continuity of insulation .8 15 Temperature index .8 16 Resistance to refrigerants.8 17 Solderability .8 18 Heat or solvent bondin

22、g9 19 Dielectric dissipation factor.9 20 Resistance to transformer oil 9 21 Loss of mass 9 23 Pin hole test .9 30 Packaging 9 Table 1 Resistance to abrasion8 BS EN 60317-25:201060317-25 IEC:2010 5 INTRODUCTION This Part of IEC 60317 is one of a series which deals with insulated wires used for windin

23、gs in electrical equipment. The series has three groups describing 1) winding wires and methods of test (IEC 60851); 2) specifications for particular types of winding wires (IEC 60317); 3) packaging of winding wires (IEC 60264). BS EN 60317-25:2010 6 60317-25 IEC:2010 SPECIFICATIONS FOR PARTICULAR T

24、YPES OF WINDING WIRES Part 25: Polyester or polyesterimide overcoated with polyamide-imide enamelled round aluminium wire, class 200 1 Scope This Part of IEC 60317 specifies the requirements of enamelled round aluminium winding wires of class 200 with a dual coating. The underlying coating is based

25、on polyester or polyesterimide resin, which may be modified providing it retains the chemical identity of the original resin and meets all specified wire requirements. The superimposed coating is based on polyamide-imide resin. NOTE A modified resin is a resin that has undergone a chemical change, o

26、r contains one or more additives to enhance certain performance or application characteristics. Class 200 is a thermal class that requires a minimum temperature index of 200 and a heat shock temperature of at least 220 C. The temperature in degrees Celsius corresponding to the temperature index is n

27、ot necessarily that at which it is recommended that the wire be operated and this will depend on many factors, including the type of equipment involved. The range of nominal conductor diameters covered by this standard is as follows: Grade 1: 0,400 mm up to and including 3,150 mm; Grade 2: 0,400 mm

28、up to and including 5,000 mm. The nominal conductor diameters are specified in Clause 4 of IEC 60317-0-3. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, th

29、e latest edition of the referenced document (including any amendments) applies. IEC 60317-0-3:2008, Specifications for particular types of winding wires Part 0-3: General requirements Enamelled round aluminium wire IEC 60851-4:1996, Winding wires Test methods Part 4: Chemical properties Amendment 1

30、(1997) Amendment 2 (1997) IEC 60851-5:2008, Winding wires Test methods Part 5: Electrical properties 3 Terms, definitions and general notes on methods of test and appearance 3.1 Terms and definitions For terms and definitions, see 3.1 of IEC 60317-0-3. BS EN 60317-25:201060317-25 IEC:2010 7 In case

31、of inconsistencies between IEC 60317-0-3 and this standard, IEC 60317-25 shall prevail. 3.2 General notes on methods of test For general notes on methods of test, see 3.2 of IEC 60317-0-3. In case of inconsistencies between IEC 60317-0-3 and this standard, IEC 60317-25 shall prevail. 3.3 Appearance

32、See 3.3 of IEC 60317-0-3. 4 Dimensions See Clause 4 of IEC 60317-0-3. 5 Electrical resistance See Clause 5 of IEC 60317-0-3. 6 Elongation See Clause 6 of IEC 60317-0-3. 7 Springiness Test appropriate but no requirements specified. 8 Flexibility and adherence See Clause 8 of IEC 60317-0-3. 9 Heat sho

33、ck See Clause 9 of IEC 60317-0-3, where the minimum heat shock temperature shall be 220 C. 10 Cut-through Test procedure and requirements under consideration. 11 Resistance to abrasion (nominal conductor diameters up to and including 2,500 mm) The wire shall meet the requirements given in Table 1. B

34、S EN 60317-25:2010 8 60317-25 IEC:2010 Table 1 Resistance to abrasion Grade 1 Grade 2 Nominal conductor diameter mm Minimum average force to failure N Minimum force to failure of each measurement N Minimum average force to failure N Minimum force to failure of each measurement N 0,400 0,450 0,500 0,

35、560 0,630 1,95 2,10 2,25 2,40 2,55 1,65 1,75 1,90 2,05 2,20 3,15 3,40 3,60 3,85 4,15 2,65 2,85 3,05 3,25 3,50 0,710 0,800 0,900 1,000 1,120 2,75 2,95 3,15 3,40 3,70 2,35 2,50 2,70 2,90 3,10 4,45 4,75 5,10 5,45 5,80 3,75 4,05 4,30 4,60 4,90 1,250 1,400 1,600 1,800 2,000 3,95 4,25 4,60 5,00 5,30 3,35

36、3,60 3,90 4,20 4,50 6,25 6,65 7,15 7,70 8,20 5,25 5,45 5,85 6,50 6,95 2,240 2,500 5,70 6,10 4,80 5,15 8,75 9,30 7,40 7,90 For intermediate nominal conductor diameters, the value of the next largest nominal conductor diameter shall be taken. 12 Resistance to solvents See Clause 12 of IEC 60317-0-3. 1

37、3 Breakdown voltage See Clause 13 of IEC 60317-0-3, where the elevated temperature shall be 200 C. 14 Continuity of insulation See Clause 14 of IEC 60317-0-3. 15 Temperature index See Clause 15 of IEC 60317-0-3, where the minimum temperature index shall be 200. 16 Resistance to refrigerants When tes

38、ted according to Clause 4 of IEC 60851-4, the percentage of extractable matter shall not exceed 0,5 %. The requirement for breakdown voltage shall be 75 % of the minimum specified value. 17 Solderability Test inappropriate. BS EN 60317-25:201060317-25 IEC:2010 9 18 Heat or solvent bonding Test inapp

39、ropriate. 19 Dielectric dissipation factor Test inappropriate. 20 Resistance to transformer oil Test inappropriate. 21 Loss of mass Test appropriate, but no requirements specified. 23 Pin hole test Test according to Clause 7 of IEC 60851-5 appropriate. Test requirements are under consideration. 30 P

40、ackaging See Clause 30 of IEC 60317-0-3. _ BS EN 60317-25:2010This page deliberately left blankThis page deliberately left blankBSI is the independent national body responsible for preparing British Standardsand other standards-related publications, information and services. It presents the UK view

41、on standards in Europe and at the international level. It is incorporated by Royal Charter.British Standards Institution (BSI)raising standards worldwideBSI Group Headquarters389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards are updated by amendment or revis

42、ion. Users of British Stan-dards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and serv-ices. We would be grateful if anyone finding an inaccuracy or ambiguity whileusing this British Standard would inform th

43、e Secretary of the technical com-mittee responsible, the identity of which can be found on the inside frontcover.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001BSI offers Members an individual updating service called PLUS which ensuresthat subscribers automatically receive the latest editions of s

44、tandards.Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001Email: Buying standardsYou may buy PDF and hard copy versions of standards directly using acredit card from the BSI Shop on the website addition all orders for BSI, international and foreign standards publicationscan be addressed to BSI Cust

45、omer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001Email: In response to orders for international standards, it is BSI policy tosupply the BSI implementation of those that have been publishedas British Standards, unless otherwise requested.Information on standardsBSI provides a wide rang

46、e of information on national, Europeanand international standards through its Knowledge Centre.Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005Email: Various BSI electronic information services are also available whichgive details on all its products and services. Tel: +44 (0)20 8996 7111 Fax: +44

47、(0)20 8996 7048Email: BSI Subscribing Members are kept up to date with standardsdevelopments and receive substantial discounts on the purchase priceof standards. For details of these and other benefits contact Membership Ad-ministration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Info

48、rmation regarding online access to British Standards via BritishStandards Online can be found at information about BSI is available on the BSI website at www.bsi- subsists in all BSI publications. BSI also holds the copyright,in the UK, of the publications of the international standardization bodies. Ex-cept as permitted under the Copyright, Designs and Patents Act 1988 no ex-tract may be reproduced, stored in a retrieval system or transmitted in anyform or by any means electronic, photocopying, recording or otherwi