BS EN 60317-47-2014 Specifications for particular types of winding wires Aromatic polyimide enamelled rectangular copper wire class 24《特种绕组线规范 24级芳香聚酰亚胺漆包扁铜线》.pdf

1、BSI Standards PublicationSpecifications for particular types of winding wiresPart 47: Aromatic polyimide enamelled rectangular copper wire, class 240BS EN 60317-47:2014National forewordThis British Standard is the UK implementation of EN 60317-47:2014. It isidentical to IEC 60317-47:2013. It superse

2、des BS EN 60317-47:1997 which iswithdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee GEL/55, Winding wires.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary

3、provisions ofa contract. Users are responsible for its correct application. The British Standards Institution 2014.Published by BSI Standards Limited 2014ISBN 978 0 580 75959 8ICS 29.060.10Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was publi

4、shed under the authority of theStandards Policy and Strategy Committee on 28 February 2014.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN 60317-47:2014EUROPEAN STANDARD EN 60317-47 NORME EUROPENNE EUROPISCHE NORM February 2014CENELEC European Committee for Elec

5、trotechnical StandardizationComit Europen de Normalisation ElectrotechniqueEuropisches Komitee fr Elektrotechnische Normung CEN-CENELEC Management Centre: Avenue Marnix 17, B - 1000 Brussels 2014 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members

6、. Ref. No. EN 60317-47:2014 E ICS 29.060.10 Supersedes EN 60317-47:1997 English version Specifications for particular types of winding wires - Part 47: Aromatic polyimide enamelled rectangular copper wire, class 240(IEC 60317-47:2013) Spcifications pour types particuliers defils de bobinage - Partie

7、 47: Fil de section rectangulaire encuivre maill avec polyimide aromatique,classe 240 (CEI 60317-47:2013) Technische Lieferbedingungen frbestimmte Typen von Wickeldrhten - Teil 47: Flachdrhte aus Kupfer,lackisoliert mit aromatischen Polyimiden, Klasse 240 (IEC 60317-47:2013) This European Standard w

8、as approved by CENELEC on 2013-11-18. CENELEC members are bound to complywith the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standardthe status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such

9、 national standards may be obtained onapplication to the CEN-CENELEC Management Centre or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any otherlanguage made by translation under the responsibility of a CENELEC member into it

10、s own language and notifiedto the CEN-CENELEC Management Centre has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedon

11、ia, France, Germany,Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland,Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. Foreword The text of document 55/1421/FDIS, future edition 2 of IEC 60

12、317-47, prepared by IEC/TC 55 “Winding wires“ was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN 60317-47:2014. The following dates are fixed: latest date by which the document has to be implemented at national level by publication of an identical national standard or by en

13、dorsement (dop) 2014-08-18 latest date by which the national standards conflicting with the document have to be withdrawn (dow) 2016-11-18 This document supersedes EN 60317-47:1997. EN 60317-47:2014 includes the following significant technical changes with respect to EN 60317-47:1997: deletion of th

14、e “in some countries” statement in the scope; new subclause containing general notes on winding wire, formerly a part of the scope; new subclause containing requirements for appearance; revision to the notes in Clause 19, Dielectric dissipation factor; new Clause 23, Pin hole test. This standard is

15、to be read in conjunction with EN 60317-0-2:2014. The numbering of clauses in this standard is not continuous from Clauses 20 and 30 in order to reserve space for possible future wire requirements prior to those for wire packaging. Attention is drawn to the possibility that some of the elements of t

16、his document may be the subject of patent rights. CENELEC and/or CEN shall not be held responsible for identifying any or all such patent rights. Endorsement notice The text of the International Standard IEC 60317-47:2013 was approved by CENELEC as a European Standard without any modification. In th

17、e official version, for Bibliography, the following notes have to be added for the standards indicated: IEC 60264 Series NOTE Harmonized as EN 60264 Series (not modified). IEC 60317 Series NOTE Harmonized as EN 60317 Series (not modified). IEC 60851 Series NOTE Harmonized as EN 60851 Series (not mod

18、ified). BS EN 60317-47:2014 EN 60317-47:2014Annex ZA (normative) Normative references to international publications with their corresponding European publications The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For

19、dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. Publication Ye

20、ar Title EN/HD Year IEC 60317-0-2 2013 Specifications for particular types of winding wires - Part 0-2: General requirements - Enamelled rectangular copper wire EN 60317-0-2 2014 BS EN 60317-47:2014 EN 60317-47:2014 2 60317-47 IEC:2013 CONTENTS INTRODUCTION . 5 1 Scope . 6 2 Normative reference . 6

21、3 Terms, definitions, general notes, and appearance 6 3.1 Terms and definitions 6 3.2 General notes 6 3.2.1 Methods of test 6 3.2.2 Winding wire 6 3.3 Appearance . 7 4 Dimensions . 7 5 Electrical resistance 7 6 Elongation 7 7 Springiness . 7 8 Flexibility and adherence 7 9 Heat shock . 7 10 Cut-thro

22、ugh 7 11 Resistance to abrasion . 7 12 Resistance to solvents 7 13 Breakdown voltage . 7 14 Continuity of insulation 8 15 Temperature index 8 16 Resistance to refrigerants . 8 17 Solderability 8 18 Heat or solvent bonding 8 19 Dielectric dissipation factor . 8 20 Resistance to transformer oil 8 21 L

23、oss of mass 8 23 Pin hole test . 8 30 Packaging. 8 Bibliography 9 BS EN 60317-47:2014 EN 60317-47:201460317-47 IEC:2013 5 INTRODUCTION This part of IEC 60317 is one of a series of standards which deals with insulated wires used for windings in electrical equipment. The series has three groups descri

24、bing: 1) Winding wires Test methods (IEC 60851); 2) Specifications for particular types of winding wires (IEC 60317); 3) Packaging of winding wires (IEC 60264). BS EN 60317-47:2014 EN 60317-47:2014 6 60317-47 IEC:2013 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES Part 47: Aromatic polyimide e

25、namelled rectangular copper wire, class 240 1 Scope This part of IEC 60317 specifies the requirements of enamelled rectangular copper winding wire of class 240 with a sole coating of aromatic polyimide resin. The range of nominal conductor dimensions covered by this standard is: width: min. 2,0 mm m

26、ax. 16,0 mm; thickness: min. 0,80 mm max. 5,60 mm. Wires of grade 1 and grade 2 are included in this specification and apply to the complete range of conductors. The specified combinations of width and thickness, as well as the specified width/thickness ratio, are given in IEC 60317-0-2. 2 Normative

27、 reference The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) appli

28、es. IEC 60317-0-2:2013, Specifications for particular types of winding wires Part 0-2: General requirements Enamelled rectangular copper wire 3 Terms, definitions, general notes, and appearance 3.1 Terms and definitions Subclause 3.1 of IEC 60317-0-2:2013 applies. 3.2 General notes 3.2.1 Methods of

29、test Subclause 3.2.1 of IEC 60317-0-2:2013 applies. In case of inconsistencies between IEC 60317-0-2: 2013 and this standard, the latter shall prevail. 3.2.2 Winding wire Class 240 is a thermal class that requires a minimum temperature index of 240 and heat shock temperature of at least 260 C. The t

30、emperature in degrees Celsius corresponding to the temperature index is not necessarily that at which it is recommended that the wire be used, and this will depend on many factors, including the type of equipment involved. BS EN 60317-47:2014 EN 60317-47:201460317-47 IEC:2013 7 3.3 Appearance Subcla

31、use 3.3 of IEC 60317-0-2:2013 applies. 4 Dimensions Clause 4 of IEC 60317-0-2:2013 applies. 5 Electrical resistance Clause 5 of IEC 60317-0-2:2013 applies. 6 Elongation Clause 6 of IEC 60317-0-2:2013 applies. 7 Springiness Clause 7 of IEC 60317-0-2:2013 applies. 8 Flexibility and adherence Clause 8

32、of IEC 60317-0-2:2013 applies. For 8.2, the wire for the adherence test shall be stretched by 10 %. 9 Heat shock Clause 9 of IEC 60317-0-2:2013 applies. The minimum heat shock temperature shall be 260 C. 10 Cut-through Clause 10 of IEC 60317-0-2:2013 applies. 11 Resistance to abrasion Test inappropr

33、iate. 12 Resistance to solvents Clause 12 of IEC 60317-0-2:2013 applies. 13 Breakdown voltage Clause 13 of IEC 60317-0-2:2013 applies. The elevated temperature shall be 240 C. BS EN 60317-47:2014 EN 60317-47:2014 8 60317-47 IEC:2013 14 Continuity of insulation Test inappropriate. 15 Temperature inde

34、x Clause 15 of IEC 60317-0-2:2013 applies. The minimum temperature index shall be 240. 16 Resistance to refrigerants Test inappropriate. 17 Solderability Test inappropriate. 18 Heat or solvent bonding Test inappropriate. 19 Dielectric dissipation factor The dielectric dissipation factor tan shall no

35、t exceed 60 104at a frequency of 1 000 Hz. NOTE Test under consideration 20 Resistance to transformer oil Test appropriate, but no requirements specified. 21 Loss of mass Test appropriate, but no requirements specified. 23 Pin hole test Test inappropriate. 30 Packaging Clause 30 of IEC 60317-0-2:201

36、3 applies. BS EN 60317-47:2014 EN 60317-47:201460317-47 IEC:2013 9 Bibliography IEC 60264 (all parts), Packaging of winding wires IEC 60317 (all parts), Specifications for particular types of winding wires IEC 60851 (all parts), Winding wires Test methods _ BS EN 60317-47:2014 EN 60317-47:2014This p

37、age deliberately left blankThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are published

38、 by BSI Standards Limited.British Standards Institution (BSI)BSI Group Headquarters389 Chiswick High Road London W4 4AL UKAbout usWe bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The kn

39、owledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge t

40、hat your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, including British and adopted European and international s

41、tandards, through our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team.SubscriptionsOur range of subscription services are designed to make u

42、sing standards easier for you. For further information on our subscription products go to British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European and international standards from your desktop. Its available 24/7 and is refreshed daily so youll always be

43、 up to date. You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member. PLUS is an updating service exclusive to BSI Subscribing Members. You will automatic

44、ally receive the latest hard copy of your standards when theyre revised or replaced. To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet. Licences can c

45、over as few or as many users as you wish. With updates supplied as soon as theyre available, you can be sure your documentation is current. For further information, email .RevisionsOur British Standards and other publications are updated by amendment or revision. We continually improve the quality o

46、f our products and services to benefit your business. If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Knowledge Centre.CopyrightAll the data, software and documentation set out in all British Standards and other BSI publications are the pro

47、perty of and copyrighted by BSI, or some person or entity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed such information to BSI for commercial publication and use. Except as permitted under the Copyright, Designs and Patents

48、Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. Details and advice can be obtained from the Copyright & Licensing Department.Useful Contacts:Customer ServicesTel: +44 845 086 9001Email (orders): Email (enquiries): SubscriptionsTel: +44 845 086 9001Email: Knowledge CentreTel: +44 20 8996 7004Email: Copyright & LicensingTel: +44 20 8996 7070Email: NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PER