1、BSI Standards PublicationSpecifications for particular types of winding wiresPart 52: Aromatic polyamide (aramid) tape wrapped round copper wire, temperature index 220BS EN 60317-52:2014National forewordThis British Standard is the UK implementation of EN 60317-52:2014. It isidentical to IEC 60317-5
2、2:2014. It supersedes BS EN 60317-52:1999 which iswithdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee GEL/55, Winding wires.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include
3、all the necessary provisions ofa contract. Users are responsible for its correct application. The British Standards Institution 2014.Published by BSI Standards Limited 2014ISBN 978 0 580 81657 4ICS 29.060.10Compliance with a British Standard cannot confer immunity fromlegal obligations.This British
4、Standard was published under the authority of theStandards Policy and Strategy Committee on 31 May 2014. Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN 60317-52:2014EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 60317-52 May 2014 ICS 29.060.10 Supersedes
5、EN 60317-52:1999 English Version Specifications for particular types of winding wires - Part 52: Aromatic polyamide (aramid) tape wrapped round copper wire, temperature index 220 (IEC 60317-52:2014) Spcifications pour types particuliers de fils de bobinage - Partie 52: Fil de section circulaire en c
6、uivre envelopp avec un ruban polyamide aromatique (aramide), dindice de temprature 220 (CEI 60317-52:2014) Technische Lieferbedingungen fr bestimmte Typen von Wickeldrhten - Teil 52: Runddrhte aus Kupfer, umwickelt mit Band aus aromatischen Polyamiden, Temperaturindex 220 (IEC 60317-52:2014) This Eu
7、ropean Standard was approved by CENELEC on 2014-03-21. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical referen
8、ces concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a C
9、ENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugos
10、lav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. European Committee for Electrotechnical Stand
11、ardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2014 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members. Ref. No. EN 60317-
12、52:2014 E BS EN 60317-52:2014EN 60317-52:2014 - 2 - Foreword The text of document 55/1395/CDV, future edition 2 of IEC 60317-52, prepared by IEC/TC 55 “Winding wires“ was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN 60317-52:2014. The following dates are fixed: latest dat
13、e by which the document has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2014-12-21 latest date by which the national standards conflicting with the document have to be withdrawn (dow) 2017-03-21 This document supersedes EN 60317-52:199
14、9. EN 60317-52:2014 includes the following significant technical changes with respect to EN 60317-52:1999: new 3.2.2 containing general notes on winding wire, formerly a part of the scope; new 3.3, containing requirements for appearance; modification to Clause 15 to delete the note on revisions to I
15、EC 60172; new Clause 23, Pin hole test. The numbering of clauses in this standard is not continuous from Clauses 20 and 30 in order to reserve space for possible future wire requirements prior to those for wire packaging. Attention is drawn to the possibility that some of the elements of this docume
16、nt may be the subject of patent rights. CENELEC and/or CEN shall not be held responsible for identifying any or all such patent rights. Endorsement notice The text of the International Standard IEC 60317-52:2014 was approved by CENELEC as a European Standard without any modification. In the official
17、 version, for Bibliography, the following notes have to be added for the standards indicated: IEC 60264 Series NOTE Harmonized as EN 60264 Series (not modified). IEC 60317 Series NOTE Harmonized as EN 60317 Series (not modified). BS EN 60317-52:2014- 3 - EN 60317-52:2014 Annex ZA (normative) Normati
18、ve references to international publications with their corresponding European publications The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references
19、, the latest edition of the referenced document (including any amendments) applies. NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. Publication Year Title EN/HD Year ISO 3 1973 Preferred numbers - Series of preferred n
20、umbers - - IEC 60172 Test procedure for the determination of the temperature index of enamelled winding wires EN 60172 IEC 60819-3-3 2011 Non-cellulosic papers for electrical purposes - Part 3: Specifications for individual materials - Sheet 3: Unfilled aramid (aromatic polyamide) papers EN 60819-3-
21、3 2011 IEC 60851 (Series) Winding wires - Test methods EN 60851-6 (Series) BS EN 60317-52:2014 2 IEC 60317-52:2014 IEC 2014 CONTENTS INTRODUCTION . 6 1 Scope 7 2 Normative references . 7 3 Terms, definitions, general notes and appearance 7 3.1 Terms and definitions 7 3.2 General notes . 8 3.2.1 Meth
22、ods of test 8 3.2.2 Winding wire 8 3.3 Appearance . 8 4 Dimensions 9 4.1 Conductor diameter . 9 4.2 Out of roundness of conductor. 9 4.3 Minimum increase in diameter due to insulation . 9 4.4 Maximum overall diameter . 10 5 Electrical resistance . 10 6 Elongation . 11 7 Springiness 11 8 Flexibility
23、and adherence 11 9 Heat shock 11 10 Cut-through . 11 11 Resistance to abrasion . 11 12 Resistance to solvents . 11 13 Breakdown voltage. 11 14 Continuity of insulation . 11 15 Temperature index . 12 16 Resistance to refrigerants 12 17 Solderability . 12 18 Heat or solvent bonding . 12 19 Dielectric
24、dissipation factor 12 20 Resistance to hydrolysis and to transformer oil . 12 21 Loss of mass . 12 23 Pin hole test . 12 30 Packaging 12 Annex A (informative) Nominal conductor diameters for intermediate sizes (R40) 14 Annex B (informative) Example of tape wrapped wire 15 Annex C (informative) Resis
25、tance. 16 Bibliography 17 Figure B.1 Illustrations of overlap . 15 BS EN 60317-52:2014IEC 60317-52:2014 IEC 2014 3 Table 1 Conductor diameters 9 Table 2 Elongation requirements 11 Table A.1 Conductor diameters (R40) . 14 Table C.1 Nominal resistance . 16 BS EN 60317-52:2014 6 IEC 60317-52:2014 IEC 2
26、014 INTRODUCTION This part of IEC 60317 is one of a series which deals with insulated wires used for windings in electrical equipment. The series has three groups describing: 1) Winding wires Test methods (IEC 60851); 2) Specifications for particular types of winding wires (IEC 60317); 3) Packaging
27、of winding wires (IEC 60264). BS EN 60317-52:2014IEC 60317-52:2014 IEC 2014 7 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES Part 52: Aromatic polyamide (aramid) tape wrapped round copper wire, temperature index 220 1 Scope This part of IEC 60317 specifies requirements for tape wrapped round c
28、opper winding wire of temperature index 220. The insulation consists of one or more wrappings of aromatic polyamide (aramid) tape of various thicknesses. NOTE The heat shock test is inappropriate for this type of wire. Therefore a heat shock temperature cannot be established. Consequently, a class b
29、ased on the requirements for temperature index and heat shock temperature cannot be specified. The range of nominal conductor diameters covered by this standard is: 1,600 mm up to and including 5,000 mm; the nominal conductor diameters are given in Table 1. 2 Normative references The following docum
30、ents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60172, Test procedure
31、for the determination of the temperature index of enamelled winding wires IEC 60819-3-3:2011, Non-cellulosic papers for electrical purposes Part 3: Specifications for individual materials Sheet 3: Unfilled aramid (aromatic polyamide) papers IEC 60851 (all parts), Winding wires Test methods ISO 3:197
32、3, Preferred numbers Series of preferred numbers 3 Terms, definitions, general notes and appearance 3.1 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1.1 class thermal performance of a wire expressed by the temperature index and the heat shock
33、temperature 3.1.2 conductor bare metal after removal of the insulation BS EN 60317-52:2014 8 IEC 60317-52:2014 IEC 2014 3.1.3 covering material which is wound, wrapped or braided around a bare or insulated conductor 3.1.4 insulation coating or covering on the conductor with the specific function of
34、withstanding voltage 3.1.5 winding wire wire used for winding a coil to provide a magnetic field 3.1.6 wire conductor coated or covered with an insulation 3.2 General notes 3.2.1 Methods of test All methods of test used in this part of IEC 60317 are given in IEC 60851. The clause numbers used in thi
35、s standard are identical to the corresponding test numbers in the IEC 60851 series of standards. In case of inconsistencies between the publication on methods of test and this standard, IEC 60317-52 shall prevail. Where no specific range of nominal conductor diameters is given for a test, the test a
36、pplies to all nominal conductor diameters covered by the specification sheet. Unless otherwise specified, all tests shall be carried out at a temperature from 15 C to 35 C and a relative humidity from 45 % to 75 %. Before measurements are made, the specimens shall be preconditioned under these atmos
37、pheric conditions for a time sufficient to allow the specimens to reach stability. The wire to be tested shall be removed from the packaging in such a way that the wire will not be subjected to tension or unnecessary bends. Before each test, sufficient wire should be discarded to ensure that any dam
38、aged wire is not included in the test specimens. 3.2.2 Winding wire The temperature in degrees Celsius corresponding to the temperature index is not necessarily that at which the wire is recommended to be operated and this will depend on many factors, including the types of equipment involved. When
39、reference is made to winding wire according to this standard, the following information should be given: reference to IEC 60317-52; diameter of the conductor; reference should also be made to the number and thickness of the tapes used and to the degree of overlap, as agreed between the purchaser and
40、 supplier. 3.3 Appearance Before wrapping, the conductor shall be completely free from copper dust and other extraneous matter. BS EN 60317-52:2014IEC 60317-52:2014 IEC 2014 9 The tape covering shall be essentially smooth and continuous, wrapped around the conductor tightly, evenly and free from cre
41、ases, wrinkles and foreign material when examined with normal vision, as wound on the original spool or reel. 4 Dimensions 4.1 Conductor diameter The series of preferred nominal conductor diameters shall correspond to series R20 according to ISO 3. The actual values and their tolerances are given in
42、 Table 1. The series of intermediate diameters from which the user may select intermediate nominal conductor diameters, when required for technical reasons, shall correspond to series R40 according to ISO 3. The actual values and their tolerances are given in Annex A. The conductor diameter shall no
43、t differ from the nominal diameter by more than the limits given in Table 1. Table 1 Conductor diameters Nominal conductor diameter Tolerance Nominal conductor diameter Tolerance mm mm mm mm 1,600 0,016 3,150 0,032 1,800 0,018 3,550 0,036 2,000 0,020 4,000 0,040 2,240 0,022 4,500 0,045 2,500 0,025 5
44、,000 0,050 2,800 0,028 NOTE The dimensions of intermediate nominal conductor diameters for R40 series are given in Annex A. 4.2 Out of roundness of conductor The difference between the minimum and maximum diameter, at any one point, shall not be more than the figure given in columns 2 and 4 of Table
45、 1. 4.3 Minimum increase in diameter due to insulation The minimum increase in diameter due to the insulation shall not be less than the values calculated using the following formula: 2 Tmin.iniwhere Tmin.i is the minimum thickness of the tape in layer number i and niis determined by the degree of o
46、verlap in that layer: for overlaps of 0 % up to, but not including 50 % n = 1; for overlaps of 50 % up to, but not including 66 % n = 2; for overlaps of 66 % up to, and including 75 % n = 3. Minimum thickness shall be calculated from the values given in Table 1 of IEC 60819-3-3:2011 where the permis
47、sible deviation of the central thickness value is: BS EN 60317-52:2014 10 IEC 60317-52:2014 IEC 2014 for nominal thickness 0,05 mm 20 % for nominal thicknesses 0,08 mm and greater 15 %. EXAMPLE 1 For a construction using two layers of 0,05 mm tape with 50 % overlap: Tmin.1 = 0,04 mm, n1= 2 Tmin.2= 0
48、,04 mm, n2= 2 Therefore, the minimum increase due to the insulation equals: 2 (0,04 2 + 0,04 2) mm = 0,320 mm EXAMPLE 2 For a construction using one layer of 0,05 mm tape with an overlap of 55 % followed by two layers of 0,08 mm tape with no overlap: Tmin.1= 0,04 mm, n1= 2 Tmin.2= 0,068 mm, n2= 1 Tm
49、in.3= 0,068 mm, n3= 1 Therefore, the minimum increase due to the insulation equals: 2 (0,04 2 + 0,068 1 + 0,068 1) mm = 0,432 mm As there are many varied constructions of this type of wire, the dimensions due to the insulation are subject to agreement between purchaser and supplier and shall be clearly stated in the purchase order. 4.4 Maximum overall diameter The overall diameter shall not exceed the sum of the maximum conductor diameter given in T
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1