BS EN 60317-58-2010 Specifications for particular types of winding wires Polyamide-imide enamelled rectangular copper wire class 220《特种绕组线规范 220级聚酰-酰亚漆包扁铜导线》.pdf

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationSpecifications for particular types of winding wiresPart 58: Polyamide-imide enamelled rectangular copper wire, class 220BS EN 60317-58:2010National forewordThis British Standard

2、 is the UK implementation of EN 60317-58:2010. It isidentical to IEC 60317-58:2010.The UK participation in its preparation was entrusted to Technical CommitteeGEL/55, Winding wires.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does

3、not purport to include all the necessary provisions of acontract. Users are responsible for its correct application. BSI 2010ISBN 978 0 580 64423 8ICS 29.060.10Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of t

4、he StandardsPolicy and Strategy Committee on 30 November 2010.Amendments issued since publicationAmd. No. Date Text affectedBRITISH STANDARDBS EN 60317-58:2010EUROPEAN STANDARD EN 60317-58 NORME EUROPENNE EUROPISCHE NORM October 2010 CENELEC European Committee for Electrotechnical Standardization Co

5、mit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Management Centre: Avenue Marnix 17, B - 1000 Brussels 2010 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 60317-58:2010 E ICS 29.060.

6、10 English version Specifications for particular types of winding wires - Part 58: Polyamide-imide enamelled rectangular copper wire, class 220 (IEC 60317-58:2010) Spcifications pour types particuliers de fils de bobinage - Partie 58: Fil de section rectangulaire en cuivre maill avec polyamide-imide

7、, classe 220 (CEI 60317-58:2010) Technische Lieferbedingungen fr bestimmte Typen von Wickeldrhten - Teil 58: Flachdrhte aus Kupfer, lackisoliert mit Polyamidimid, Klasse 220 (IEC 60317-58:2010) This European Standard was approved by CENELEC on 2010-10-01. CENELEC members are bound to comply with the

8、 CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or

9、 to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the offici

10、al versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, P

11、ortugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. BS EN 60317-58:2010EN 60317-58:2010 - 2 - Foreword The text of document 55/1138/CDV, future edition 1 of IEC 60317-58, prepared by IEC TC 55, Winding wires, was submitted to the IEC-CENELEC parallel vote and was

12、 approved by CENELEC as EN 60317-58 on 2010-10-01. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and CENELEC shall not be held responsible for identifying any or all such patent rights. The following dates were fixed: latest

13、 date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2011-07-01 latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 2013-10-01 Annex ZA has been added by CENELEC. _ Endorsemen

14、t notice The text of the International Standard IEC 60317-58:2010 was approved by CENELEC as a European Standard without any modification. _ BS EN 60317-58:2010- 3 - EN 60317-58:2010 Annex ZA (normative) Normative references to international publications with their corresponding European publication

15、s The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE When an international publication has been

16、 modified by common modifications, indicated by (mod), the relevant EN/HD applies. Publication Year Title EN/HD Year IEC 60317-0-2 + A1 + A2 1997 1999 2005 Specifications for particular types of winding wires - Part 0-2: General requirements - Enamelled rectangular copper wire EN 60317-0-2 + A1 + A2

17、 1998 2000 2005 BS EN 60317-58:2010 2 60317-58 IEC:2010 CONTENTS INTRODUCTION.5 1 Scope.6 2 Normative references .6 3 Definitions and general notes on methods of test and appearance6 3.1 Definitions and general notes on methods of test 6 3.2 Appearance.7 4 Dimensions 7 5 Electrical resistance .7 6 E

18、longation 7 7 Springiness 7 8 Flexibility and adherence7 9 Heat shock .7 10 Cut-through 7 11 Resistance to abrasion .7 12 Resistance to solvents7 13 Breakdown voltage .7 14 Continuity of insulation .7 15 Temperature index .8 16 Resistance to refrigerants.8 17 Solderability .8 18 Heat bonding8 19 Die

19、lectric dissipation factor.8 20 Resistance to transformer oil 8 21 Loss of mass 8 23 Pin hole test .8 30 Packaging 8 BS EN 60317-58:201060317-58 IEC:2010 5 INTRODUCTION This part of IEC 60317 is one of a series which deals with insulated wires used for windings in electrical equipment. The series ha

20、s three groups describing 1) winding wires test methods (IEC 60851); 2) specifications for particular types of winding wires (IEC 60317); 3) packaging of winding wires (IEC 60264). BS EN 60317-58:2010 6 60317-58 IEC:2010 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES Part 58: Polyamide-imide e

21、namelled rectangular copper wire, class 220 1 Scope This part of IEC 60317 specifies the requirements of enamelled rectangular copper winding wire of class 220 with a sole coating based on polyamide-imide resin, which may be modified providing it retains the chemical identity of the original resin a

22、nd meets all specified wire requirements. Class 220 is a thermal class that requires a minimum temperature index of 220 and a heat shock temperature of at least 240 C. The temperature in degrees Celsius corresponding to the temperature index is not necessarily that at which it is recommended that th

23、e wire be operated and this will depend on many factors, including the type of equipment involved. The range of nominal conductor dimensions covered by this standard is as follows: width: min. 2,0 mm; max. 16,0 mm; thickness: min. 0,80 mm; max. 5,60 mm. Wires of grade 1 and grade 2 are included in t

24、his specification and apply to the complete range of conductors. The specified combinations of width and thickness as well as the specified ratio width/thickness are given in IEC 60317-0-2. 2 Normative references The following referenced documents are indispensable for the application of this docume

25、nt. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60317-0-2:1997, Specifications for particular types of winding wires Part 0: General requirements Section 2: Enamelled rectangular c

26、opper wire Amendment 1 (1999) Amendment 2 (2005) 3 Definitions and general notes on methods of test and appearance 3.1 Definitions and general notes on methods of test For definitions and general notes on methods of test, see Clause 3 of IEC 60317-0-2. In case of inconsistencies between IEC 60317-0-

27、2 and this standard, IEC 60317-58 shall prevail. BS EN 60317-58:201060317-58 IEC:2010 7 3.2 Appearance See Subclause 3.3 of IEC 60317-0-2. 4 Dimensions See Clause 4 of IEC 60317-0-2. 5 Electrical resistance See Clause 5 of IEC 60317-0-2. 6 Elongation See Clause 6 of IEC 60317-0-2. 7 Springiness See

28、Clause 7 of IEC 60317-0-2. 8 Flexibility and adherence See Clause 8 of IEC 60317-0-2. 9 Heat shock See Clause 9 of IEC 60317-0-2, where the minimum heat shock temperature shall be 240 C. 10 Cut-through Test requirements under consideration. 11 Resistance to abrasion Test inappropriate. 12 Resistance

29、 to solvents See Clause 12 of IEC 60317-0-2. 13 Breakdown voltage See Clause 13 of IEC 60317-0-2, where the elevated temperature shall be 220 C. 14 Continuity of insulation Test inappropriate. BS EN 60317-58:2010 8 60317-58 IEC:2010 15 Temperature index See Clause 15 of IEC 60317-0-2, where the mini

30、mum temperature index shall be 220. 16 Resistance to refrigerants Test inappropriate. 17 Solderability Test inappropriate. 18 Heat bonding Test inappropriate. 19 Dielectric dissipation factor Test inappropriate. 20 Resistance to transformer oil Test under consideration. 21 Loss of mass Test inapprop

31、riate. 23 Pin hole test Test inappropriate. 30 Packaging See Clause 30 of IEC 60317-0-2. _ BS EN 60317-58:2010This page deliberately left blankBSI is the independent national body responsible for preparing British Standardsand other standards-related publications, information and services. It presen

32、ts the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.British Standards Institution (BSI)raising standards worldwideBSI Group Headquarters389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards are updated by ame

33、ndment or revision. Users of British Stan-dards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and serv-ices. We would be grateful if anyone finding an inaccuracy or ambiguity whileusing this British Standard

34、would inform the Secretary of the technical com-mittee responsible, the identity of which can be found on the inside frontcover.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001BSI offers Members an individual updating service called PLUS which ensuresthat subscribers automatically receive the lates

35、t editions of standards.Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001Email: Buying standardsYou may buy PDF and hard copy versions of standards directly using acredit card from the BSI Shop on the website addition all orders for BSI, international and foreign standards publicationscan be addres

36、sed to BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001Email: In response to orders for international standards, it is BSI policy tosupply the BSI implementation of those that have been publishedas British Standards, unless otherwise requested.Information on standardsBSI provi

37、des a wide range of information on national, Europeanand international standards through its Knowledge Centre.Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005Email: Various BSI electronic information services are also available whichgive details on all its products and services. Tel: +44 (0)20 8996

38、 7111 Fax: +44 (0)20 8996 7048Email: BSI Subscribing Members are kept up to date with standardsdevelopments and receive substantial discounts on the purchase priceof standards. For details of these and other benefits contact Membership Ad-ministration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 70

39、01 Email: Information regarding online access to British Standards via BritishStandards Online can be found at information about BSI is available on the BSI website at www.bsi- subsists in all BSI publications. BSI also holds the copyright,in the UK, of the publications of the international standa

40、rdization bodies. Ex-cept as permitted under the Copyright, Designs and Patents Act 1988 no ex-tract may be reproduced, stored in a retrieval system or transmitted in anyform or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not pre

41、clude the freeuse, in the course of implementing the standard of necessary details such assymbols, and size, type or grade designations. If these details are to be usedfor any other purpose than implementation then the prior written permissionof BSI must be obtained. Details and advice can be obtained from the Copy-right & Licensing Manager.Tel: +44 (0)20 8996 7070Email: