BS EN 60454-3-7-1998 Specifications for pressure-sensitive adhesive tapes for electrical purposes - Specifications for individual materials - Polyimide film tapes with pressure-sen.pdf

1、BRITISH STANDARD BS EN 60454-3-7:1998 IEC 60454-3-7:1998 Pressure-sensitive adhesive tapes for electrical purposes Part 3: Specifications for individual materials Sheet 7: Polyimide film tapes with pressure-sensitive adhesive The European Standard EN60454-3-7:1998 has the status of a British Standar

2、d ICS 29.035.20BS EN 60454-3-7:1998 This British Standard, having been prepared under the directionof the Electrotechnical Sector Board, was published underthe authority of the Standards Board and comesintoeffect on 15 October1998 BSI 06-1999 ISBN 0 580 30065 X National foreword This British Standar

3、d is the English language version of EN60454-3-7:1998. It is identical with IEC60454-3-7:1998. The UK participation in its preparation was entrusted by Technical Committee GEL/15, Insulating materials, to Subcommittee GEL/15/3, Material specifications, which has the responsibility to: aid enquirers

4、to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. A list of organizations represe

5、nted on this subcommittee can be obtained on request to its secretary. From1 January1997, all IEC publications have the number60000 added to the old number. For instance, IEC27-1 has been renumbered as IEC60027-1. For a period of time during the change over from one numbering system to the other, pu

6、blications may contain identifiers from both systems. NOTEBS3924:1978, Specification for pressure-sensitive adhesive tapes for electrical insulating purposes, will be withdrawn after Sheets1 to19 (inclusive) of BS EN60454-3 have been published. Cross-references Attention is drawn to the fact that CE

7、N and CENELEC standards normally include an annex which lists normative references to international publications with their corresponding European publications. The British Standards which implement these international or European publications may be found in the BSI Standards Catalogue under the se

8、ction entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct applicatio

9、n. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, theENtitle page, pages2 to6 and a back cover. This standard has been updated (see copyright date) and may ha

10、ve had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Amendments issued since publication Amd. No. Date CommentsBS EN 60454-3-7:1998 BSI 06-1999 i Contents Page National foreword Inside front cover Foreword 2 Text of EN 60454-3-7 3ii blankEUROPEAN S

11、TANDARD NORME EUROPENNE EUROPISCHE NORM EN60454-3-7 April1998 ICS 29.035.20 Descriptors: Electrical insulation, solid electrical insulating materials, adhesive tapes, carbonates, thermoplastic resins, acrylic fibres, specifications English version Pressure-sensitive adhesive tapes for electrical pur

12、poses Part3: Specifications for individual materials Sheet7: Polyimide film tapes with pressure-sensitive adhesive (IEC60454-3-7:1998) Rubans adhsifs sensibles la pression usages lectriques Partie3: Spcifications pour matriaux particuliers Feuille7: Rubans en polyimide avec un adhsifsensible la pres

13、sion (CEI60454-3-7:1998) Selbstklebende Bnder fr elektrotechnischeAnwendungen Teil3: Bestimmungen fr einzelne Materialien Blatt7: Anforderungen fr selbstklebende Bnder aus Polyimid-Folien (IEC60454-3-7:1998) This European Standard was approved by CENELEC on 1998-04-01. CENELEC members are bound to c

14、omply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central

15、Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status

16、 as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, CzechRepublic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CENELEC European C

17、ommittee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B-1050 Brussels 1998 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC

18、members. Ref. No. EN60454-3-7:1998 EEN60454-3-7:1998 BSI 06-1999 2 Foreword The text of document15C/857/FDIS, future edition2 of IEC60454-3-7, prepared by SC15C, Specifications, of IEC TC15, Insulating materials, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN60454-3

19、-7 on 1998-04-01. The following dates were fixed: Annexes designated “normative” are part of the body of the standard. In this standard, Annex ZA is normative. Annex ZA has been added by CENELEC. Endorsement notice The text of the International Standard IEC60454-3-7:1998 was approved by CENELEC as a

20、 European Standard without any modification. Contents Page Foreword 2 Introduction 3 1 General 3 2 Classification and designation 3 3 Requirements 3 4 Test methods 4 5 Marking, labelling and packaging 4 Annex ZA (normative) Normative references to international publications with their corresponding

21、European publications 6 Table 1 Requirements for all types 4 Table 2 Requirements for various types 5 latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 1999-01-01 latest date by which the national standards co

22、nflicting with the EN have to be withdrawn (dow) 2001-01-01EN60454-3-7:1998 BSI 06-1999 3 Introduction This International Standard is one of a series which deals with pressure-sensitive adhesive tapes, intended primarily for electrical purposes. The series consists of three parts: Part 1: General re

23、quirements (IEC60454-1); Part 2: Methods of test (IEC60454-2); Part 3: Specifications for individual materials (IEC60454-3). This standard contains one of the sheets comprising part3 as follows: Sheet7: Polyimide film tapes with pressure-sensitive adhesive. 1 General 1.1 Scope This sheet of IEC60454

24、-3 contains the requirements for pressure-sensitive adhesive tapes made with polyimide film. Materials which conform to this specification meet established levels of performance. However, the selection of a material by a user for a specific application should be based on the actual requirements nece

25、ssary for adequate performance in that application, and not based on this specification alone. 1.2 Normative references The following normative documents contain provisions which, through reference in this text, constitute provisions of this sheet of IEC60454-3. At the time of publication, the editi

26、ons indicated were valid. All normative documents are subject to revision and parties to agreements based on this sheet of IEC60454-3 are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below 1) . Members of IEC and ISO maintain reg

27、isters of currently valid International Standards. IEC60426:1973, Test methods for determining electrolytic corrosion with insulating materials. IEC60454-1:1992, Specifications for pressure-sensitive adhesive tapes for electrical purposes Part1: General requirements. IEC60454-2:1994, Specification f

28、or pressure-sensitive adhesive tapes for electrical purposes Part2: Methods of test. 1.3 Definitions Refer to IEC60454-1 for definitions applicable to these materials. 2 Classification and designation 2.1 The products supplied according to this specification shall be classified as follows: 2.2 The p

29、roducts shall be designated for ordering purposes as follows: 3 Requirements 3.1 All applicable requirements of IEC60454-1 shall apply to material furnished under this specification. 3.2 The physical and electrical properties of products supplied according to this specification shall be within the l

30、imits listed in Table 1 and Table 2 when tested in accordance with the test methods listed therein. 1) In case of dispute, the reference edition is applicable. Type1: Products having properties characteristic of a polyimide film of nominal thickness0,020mm to0,030mm with a thermal index of155with an

31、 acrylic crosslinked adhesive. Type2: Products having properties characteristic of a polyimide film of nominal thickness0,020mm to0,030mm with a thermal index of180with a silicone thermosetting adhesive. Type3: Products having properties characteristic of a polyimide film of nominal thickness0,045mm

32、 to0,055mm with a thermal index of155with an acrylic crosslinked adhesive. Type4: Products having properties characteristic of a polyimide film of nominal thickness0,045mm to0,055)mm with a thermal index of180 with a silicone thermosetting adhesive. Type1: IEC454-3-7-1/F-PI/155/A-Tx. Type2: IEC454-3

33、-7-2/F-PI/180/S-Tc. Type3: IEC454-3-7-3/F-PI/155/A-Tx. Type4: IEC454-3-7-4/F-PI/180/S-Tc.EN60454-3-7:1998 4 BSI 06-1999 3.3 Thermal endurance When required by the purchaser, the manufacturer shall provide evidence that when tested in accordance with clause 21 of IEC60454-2, the product has a tempera

34、ture index of not less than155 for types1 and3, and180 for types2 and4. The exposure temperatures are170C, 190C, and210C for types1 and3, and200C,225C, and250C for types2 and4. The end-point criterion used shall be: for breakdown voltage:1,5kV for types1and2, and2,0kV for types3 and4 (metal foil ele

35、ctrode). 4 Test methods All tests shall be conducted in accordance with the appropriate clauses and subclauses of IEC60454-2. 5 Marking, labelling and packaging Unless otherwise specified, all marking, labelling and packaging shall be in accordance with the requirements of IEC60454-1. Table 1 Requir

36、ements for all types Properties Clause or subclause of IEC60454-2 Units Requirements Thickness 4 mm Nominal value per manufacturer 0,01mm or 15% whichever is greater Width 5 mm 7.2.1 of IEC60454-1 Length 6 m 7.3 of IEC60454-1 Electrolytic corrosion: insulation resistance after24h at(23 2)C and(93 2)

37、 % relative humidity or visual method 7.5 7.6 7/25mm width None 1 10 11minimum Grade shall be at least as good as A1,4 (see Table1 of IEC60426) Elongation at break 8 % 40 minimum Flagging test 15 Condition per15.5.1 mm 2 maximum Flame test 20 Flame retardant Thermal endurance 21 See3.3EN60454-3-7:19

38、98 BSI 06-1999 5 Table 2 Requirements for various types Properties Clause or subclause of IEC60454-2 Units Type1 Type2 Type3 Type4 Tensile strength 8 N/10mm width 30 minimum 30 minimum 60 minimum 60 minimum Adhesion to steel 11 N/10mm width 2,0 minimum 2,0 minimum 2,5 minimum 2,5 minimum Adhesion to

39、 backing 11 N/10mm width 0,5 to3,0 1,5 to3,0 0,5 to4,0 1,5 to4,0 Bond separation during thermal treatment 14.1, except use(200 5)g mass and test at130C 3 passes 3 passes Bond separation after thermal treatment 14.2 3 passes 3 passes Breakdown voltage: at room temperature after humid conditioning 17

40、18 kV kV 4,5 minimum 3,2 minimum 4,5 minimum 3,2 minimum 7,0 minimum 5,0 minimum 7,0 minimum 5,0 minimumEN60454-3-7:1998 6 BSI 06-1999 Annex ZA (normative) Normative references to international publications with their corresponding European publications This European Standard incorporates by dated o

41、r undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only

42、 when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies (including amendments). NOTEWhen an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. Publication Yea

43、r Title EN/HD Year IEC60426 1973 Test methods for determining electrolytic corrosionwith insulating materials IEC60454-1 1992 Specifications for pressure-sensitive adhesive tapesfor electrical purposes Part1: General requirements EN60454-1 1994 IEC60454-2 1994 Part2: Methods of test EN60454-2 1995bl

44、ankBS EN 60454-3-7:1998 IEC 60454-3-7:1998 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Roy

45、al Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an in

46、accuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that s

47、ubscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to

48、supply the BSI implementation of those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Variou

49、s BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also