BS EN 60512-13-2-2006 Connectors for nelectronic equipment — nTests and nmeasurements — nPart 13-2 Mechanical operation tests — nTest 13b Insertion and withdrawal nforces《电子设备用连接器 .pdf

1、BRITISH STANDARDBS EN 60512-13-2: 2006Connectors for electronic equipment Tests and measurements Part 13-2: Mechanical operation tests Test 13b: Insertion and withdrawal forcesICS 31.220.10g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g5

2、1g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58BS EN 60512-13-2:2006This British Standard was published under the authority of the Standards Policy and Strategy Committee on 28 April 2006 BSI 2007ISBN 978 0 580 60806 3National forewordThis British Standard i

3、s the UK implementation of EN 60512-13-2:2006, incorporating corrigendum December 2006. It is identical with IEC 60512-13-2:2006.The UK participation in its preparation was entrusted to Technical Committee EPL/48, Electromechanical components and mechanical structures for electronic equipment. A lis

4、t of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard cannot confer immunity from lega

5、l obligations.Amendments issued since publicationDate Comments31 December 2007 Implementation of CENELEC corrigendum December 2006 (addition of Annex ZA)EUROPEAN STANDARD EN 60512-13-2NORME EUROPENNE EUROPISCHE NORM March 2006 CENELECEuropean Committee for Electrotechnical Standardization Comit Euro

6、pen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B - 1050 Brussels 2006 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 60512-13-2:2006 E ICS 31.220.10

7、 Incorporating corrigendum December 2006English version Connectors for electronic equipment - Tests and measurements Part 13-2: Mechanical operation tests - Test 13b: Insertion and withdrawal forces (IEC 60512-13-2:2006)Connecteurs pour quipements lectroniques - Essais et mesures Partie 13-2: Essais

8、 de fonctionnement mcanique - Essai 13b: Forces dinsertion et dextraction (CEI 60512-13-2:2006) Steckverbinder fr elektronische Einrichtungen - Mess- und Prfverfahren Teil 13-2: Prfungen der mechanischen Bedienbarkeit - Prfung 13b: Gesamtsteck- und -ziehkraft(IEC 60512-13-2:2006) This European Stand

9、ard was approved by CENELEC on 2006-03-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerni

10、ng such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its

11、 own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latv

12、ia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Foreword The text of document 48B/1582/FDIS, future edition 1 of IEC 60512-13-2, prepared by SC 48B, Connectors, of IEC TC 48, Electromechanica

13、l components and mechanical structures for electronic equipment, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 60512-13-2 on 2006-03-01. This standard is to be read in conjunction with EN 60512-1 and EN 60512-1-100 which explains the structure of the EN 60512 serie

14、s. The following dates were fixed: latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2006-12-01 latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 2009-03-01 Annex Z

15、A has been added by CENELEC. _ Endorsement notice The text of the International Standard IEC 60512-13-2:2006 was approved by CENELEC as a European Standard without any modification. _ EN 60512-13-2:2006 2 3 EN 60512-13-2:2006CONNECTORS FOR ELECTRONIC EQUIPMENT TESTS AND MEASUREMENTS Part 13-2: Mecha

16、nical operation tests Test 13b: Insertion and withdrawal forces 1 Scope and object This part of IEC 60512, when required by the detail specification, is used for testing connectors within the scope of IEC technical committee 48. It may also be used for similar devices when specified in a detail spec

17、ification. The object of this part of IEC 60512 is to detail a standard test method to measure the insertion and withdrawal forces of mating connectors, or of a connector with the mating insertion and/or withdrawal gauge(s) specified in the connector detail specification, without the effect of any l

18、ocking, latching, sealing, engaging, separating or similar device. NOTE 1 This may, for some designs, involve irreversible alteration to the connectors. The connector may be a single pair of contacts without the influence of any housing, or a contact or contacts in a housing where parts of this hous

19、ing have been disabled or removed in order to eliminate their influence on the test and measurements. NOTE 2 When in the following text the word “connector(s)” is used, this is also applicable to individual contact pairs. 2 Normative references The following referenced documents are indispensable fo

20、r the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60512-1-1, Connectors for electronic equipment Tests and measurements Part 1-1: General examination

21、Test 1a: Visual examination 3 Preparation 3.1 Preparation of specimen The specimen shall consist of a mating pair of connectors with all contacts in place or two mating contacts as applicable, and as given in the detail specification. Any locking, latching, sealing, engaging, separating, or similar

22、device shall be rendered inoperative. 3.2 Test gauge If specified in the detail specification, a gauge(s) to that specification shall be provided. NOTE It is recommended that in addition to measurements of the insertion and withdrawal forces generated between connector pairs, gauge(s) designed to si

23、mulate max/min dimensions of the connector system, are used and the forces re-measured with the appropriate mating parts. EN 60512-13-2:2006 4 3.3 Lubricant If the detail specification so requires, the specified lubricant shall be applied in the manner given in the detail specification. 3.4 Mounting

24、 One of the connectors shall be rigidly fixed in position. The mating part shall be free to self-align using only such means that are provided by the connectors under test. 4 Method 4.1 Rate of insertion and withdrawal The rate of insertion and withdrawal shall be 50 mm/min maximum, at constant spee

25、d, unless otherwise stated in the detail specification. 4.2 Insertion and withdrawal The connectors shall be fully inserted and withdrawn, without the effect of any locking, latching, sealing, engaging, separating, or similar device, in a normal manner unless special instructions are given in the de

26、tail specification. This shall be done the number of times stated in the detail specification. 4.3 Measurements 4.3.1 Initial measurements Visual examination according to IEC 60512-1-1 shall be done. There shall be no defects that would impair the validity of the test. 4.3.2 Test measurements The fo

27、rces to fully insert and withdraw the connectors shall be measured. This shall be done as many times as required by the detail specification. At least, the forces for the first and last cycle shall be recorded. 4.3.3 Final measurements Visual examination according to IEC 60512-1-1 shall be done with

28、 10u magnifications. Any defects, which would impair the normal functioning of the connector, shall be documented. 5 Details to be specified When this test is required by a detail specification, the following shall be given therein: a) maximum value of the insertion force; b) maximum and minimum val

29、ues of the withdrawal force; c) rate of insertion and withdrawal, if other than those given in 4.1; 5 EN 60512-13-2:2006d) details of size and method of use of (maximum-minimum) gauges, if applicable; e) number of insertion and withdrawal cycles; f) lubricant to be applied, means and quantity, or st

30、ate lubricant not required; g) any deviation from the standard test method. _Annex ZA (normative) Normative references to international publications with their corresponding European publications The following referenced documents are indispensable for the application of this document. For dated ref

31、erences, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. Publication Year Title

32、EN/HD Year IEC 60512-1-1 -1)Connectors for electronic equipment - Tests and measurements Part 1-1: General examination - Test 1a: Visual examination EN 60512-1-1 20022)_ 1)Undated reference. 2)Valid edition at date of issue. EN 60512-13-2:2006 6 blankBS EN 60512-13-2: 2006BSI389 Chiswick High RoadLo

33、ndonW4 4ALBSI British Standards InstitutionBSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revis

34、ion. Users of British Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the

35、 Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions o

36、f standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-.In response to orders

37、for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European and international standards through its Library and

38、 its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-.Subscribing members of BSI are kept up to

39、date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-.Information regarding online access to British S

40、tandards via British Standards Online can be found at http:/www.bsi- information about BSI is available on the BSI website at http:/www.bsi-.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies.

41、Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI.This does not preclude the free use,

42、in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.