BS EN 60512-21-1-2010 Connectors for electronic nequipment Tests and nmeasurements nPart 21-1 R F resistance tests Test 21a nR F shunt resistance《电子设备连接器 试验和测量 第21-1部分 无线电频率电阻试验 试.pdf

1、raising standards worldwide NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW BSI Standards Publication BS EN 60512-21-1:2010 Connectors for electronic equipment Tests and measurements Part 21-1: R.F. resistance tests Test 21a: R.F. shunt resistance Incorporating Corrigendum Sep

2、tember 2010BS EN 60512-21-1:2010BRITISH STANDARD National foreword This British Standard is the UK implementation of EN 60512-21-1:2010. It is identical to IEC 60512-21-1:2010. It supersedes Test 21a from BS 5772-9:1993, IEC 60512-9:1992, which will remain current until all the tests it contains hav

3、e been revised. The UK participation in its preparation was entrusted to Technical Committee EPL/48, Electromechanical components and mechanical structures for electronic equipment. A list of organizations represented on this committee can be obtained on request to its secretary. This publication do

4、es not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. BSI 2010 ISBN 978 0 580 72935 5 ICS 31.220.01 Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was published under the autho

5、rity of the Standards Policy and Strategy Committee on 31 August 2010. Amendments issued since publication Date Text affected 30 September 2010 Correction to wrong CENELEC and IEC documents published. EUROPEAN STANDARD EN 60512-21-1 NORME EUROPENNE EUROPISCHE NORM July 2010 CENELEC European Committe

6、e for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Management Centre: Avenue Marnix 17, B - 1000 Brussels 2010 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members

7、. Ref. No. EN 60512-21-1:2010 E ICS 31.220.01 English version Connectors for electronic equipment - Tests and measurements - Part 21-1: R.F. resistance tests - Test 21a: R.F. shunt resistance (IEC 60512-21-1:2010) Connecteurs pour quipements lectroniques - Essais et mesures - Partie 21-1: Essais de

8、rsistance aux frquences radiolectriques - Essai 21a: Rsistance parallle aux frquences radiolectriques (CEI 60512-21-1:2010) Steckverbinder fr elektronische Einrichtungen - Mess- und Prfverfahren - Teil 21-1: Prfungen der HF-Gte - Prfung 21a: HF-Dmpfungswiderstand (IEC 60512-21-1:2010) This European

9、Standard was approved by CENELEC on 2010-07-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references con

10、cerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member int

11、o its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Icela

12、nd, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. EN 60512-21-1:2010 - 2 - Foreword The text of document 48B/2151/FDIS, future edition 1 of IEC 60512-21-1, prepared by S

13、C 48B, Connectors, of IEC TC 48, Electromechanical components and mechanical structures for electronic equipment, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 60512-21-1 on 2010-07-01. Attention is drawn to the possibility that some of the elements of this documen

14、t may be the subject of patent rights. CEN and CENELEC shall not be held responsible for identifying any or all such patent rights. The following dates were fixed: latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (

15、dop) 2011-04-01 latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 2013-07-01 _ Endorsement notice The text of the International Standard IEC 60512-21-1:2010 was approved by CENELEC as a European Standard without any modification. _ 4 60512-21-1 IEC:2010 C

16、ONNECTORS FOR ELECTRONIC EQUIPMENT TESTS AND MEASUREMENTS Part 21-1: RF resistance tests Test 21a: RF shunt resistance 1 Scope and object This part of IEC 60512, when required by the detail specification, is used for testing connectors within the scope of technical committee 48. It may also be used

17、for similar devices when specified in a detail specification. The object of this standard is to detail a standard test method to determine the value of RF shunt resistance which degrades the quality factor of an L/C circuit when a connector is connected in parallel. This value is expressed in terms

18、of a parallel damping resistance. 2 Preparation of the specimen The specimen shall be prepared and mounted according to the detail specification. 3 Test method The R.F. shunt resistance shall be measured with suitable measuring equipment. The measuring points shall be specified in the detail specifi

19、cation. The measuring error shall not exceed 10 %. The test frequency shall be specified in the detail specification. The preferred frequencies are: 1 MHz, 10 MHz, 30 MHz and 100 MHz. 4 Requirements The value of RF shunt resistance shall be not less than the value specified in the detail specificati

20、on. 5 Details to be specified When this test is required by the detail specification, the following details shall be specified: a) preparation and mounting of the specimen; b) measuring points; c) measuring frequency; d) minimum value of RF shunt resistance; e) any deviation from the standard test m

21、ethod. _ This page deliberately left blankBSI is the independent national body responsible for preparing British Standards and other standards-related publications, information and services. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Ch

22、arter. British Standards Institution (BSI) raising standards worldwide BSI Group Headquarters 389 Chiswick High Road London W4 4AL UK Tel +44 (0)20 8996 9001 Fax +44 (0)20 8996 7001 British Standards are updated by amendment or revision. Users of British Stan- dards should make sure that they posse

23、ss the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and serv- ices. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical com- mittee responsible, the iden

24、tity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001 BSI offers Members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 70

25、01 Email: Buying standards You may buy PDF and hard copy versions of standards directly using a credit card from the BSI Shop on the website In addition all orders for BSI, international and foreign standards publications can be addressed to BSI Customer Services. Tel: +44 (0)20 8996 9001 Fax: +44

26、 (0)20 8996 7001 Email: In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European an

27、d international standards through its Knowledge Centre. Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005 Email: Various BSI electronic information services are also available which give details on all its products and services. Tel: +44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048 Email: BSI Subscrib

28、ing Members are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Ad- ministration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access

29、 to British Standards via British Standards Online can be found at Further information about BSI is available on the BSI website at www.bsi- Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodie

30、s. Ex- cept as permitted under the Copyright, Designs and Patents Act 1988 no ex- tract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the fr

31、ee use, in the course of implementing the standard of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copy- right & Licensing Manager. Tel: +44 (0)20 8996 7070 Email: