BS EN 60512-9-2-2012 Connectors for electronic equipment Tests and measurements Endurance tests Test 9b Electrical load and temperature《电子设备连接器 试验和测量 耐久性试验 试验9b 电力负载和温度》.pdf

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationConnectors for electronic equipment Tests and measurementsPart 9-2: Endurance tests Test 9b: Electrical load and temperatureBS EN 60512-9-2:2012National forewordThis British Stan

2、dard is the UK implementation of EN 60512-9-2:2012. It is identical to IEC 60512-9-2:2011. It supersedes Test 9b from BS 5772-5:1993, IEC 60512-5:1992 which will remain current until all the tests have been revised.The UK participation in its preparation was entrusted to Technical Committee EPL/48,

3、Electromechanical components and mechanical structures for electronic equipment.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its cor

4、rect application. The British Standards Institution 2012Published by BSI Standards Limited 2012 ISBN 978 0 580 62125 3 ICS 31.220.01Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Str

5、ategy Committee on 31 March 2012.Amendments issued since publicationAmd. No. Date Text affectedBRITISH STANDARDBS EN 60512-9-2:2012EUROPEAN STANDARD EN 60512-9-2 NORME EUROPENNE EUROPISCHE NORM February 2012 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisati

6、on Electrotechnique Europisches Komitee fr Elektrotechnische Normung Management Centre: Avenue Marnix 17, B - 1000 Brussels 2012 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 60512-9-2:2012 E ICS 31.220.01 English version Connec

7、tors for electronic equipment - Tests and measurements - Part 9-2: Endurance tests - Test 9b: Electrical load and temperature (IEC 60512-9-2:2011) Connecteurs pour quipements lectroniques - Essais et mesures - Partie 9-2: Essais dendurance - Essai 9b: Charge lectrique et temprature (CEI 60512-9-2:20

8、11) Steckverbinder fr elektronische Einrichtungen - Mess- und Prfverfahren - Teil 9-2: Dauerprfungen - Prfung 9b: Elektrische Belastung bei hoher Temperatur (IEC 60512-9-2:2011) This European Standard was approved by CENELEC on 2012-01-02. CENELEC members are bound to comply with the CEN/CENELEC Int

9、ernal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to an

10、y CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the of

11、ficial versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Polan

12、d, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 60512-9-2:2012EN 60512-9-2:2012 Foreword The text of document 48B/2243/FDIS, future edition 1 of IEC 60512-9-2, prepared by SC 48B, “Connectors“, of IEC TC 48, “Electromechanical components and

13、 mechanical structures for electronic equipment“ was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN 60512-9-2:2012. The following dates are fixed: latest date by which the document has to be implemented at national level by publication of an identical national standard or b

14、y endorsement (dop) 2012-10-02 latest date by which the national standards conflicting with the document have to be withdrawn (dow) 2015-01-02 Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC and/or CEN shall not be held re

15、sponsible for identifying any or all such patent rights. Endorsement notice The text of the International Standard IEC 60512-9-2:2011 was approved by CENELEC as a European Standard without any modification. BS EN 60512-9-2:2012EN 60512-9-2:2012 Annex ZA (normative) Normative references to internatio

16、nal publications with their corresponding European publications The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the

17、 referenced document (including any amendments) applies. NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. Publication Year Title EN/HD Year IEC 60512-1-1 - Connectors for electronic equipment - Tests and measurements -

18、Part 1-1: General examination - Test 1a: Visual examination EN 60512-1-1 - IEC 60512-1-100 - Connectors for electronic equipment - Tests and measurements - Part 1-100: General - Applicable publications EN 60512-1-100 - IEC 60512-2-1 - Connectors for electronic equipment - Tests and measurements - Pa

19、rt 2-1: Electrical continuity and contact resistance tests - Test 2a: Contact resistance - Millivolt level method EN 60512-2-1 - IEC 60512-2-6 - Connectors for electronic equipment - Tests and measurements - Part 2-6: Electrical continuity and contact resistance tests - Test 2f: Housing (shell) elec

20、trical continuity EN 60512-2-6 - IEC 60512-3-1 - Connectors for electronic equipment - Tests and measurements - Part 3-1: Insulation tests - Test 3a: Insulation resistance EN 60512-3-1 - IEC 60512-4-1 - Connectors for electronic equipment - Tests and measurements - Part 4-1: Voltage stress tests - T

21、est 4a: Voltage proof EN 60512-4-1 - BS EN 60512-9-2:201260512-9-2 IEC:2011 CONTENTS 1 Scope and object . 5 2 Normative references . 5 3 Preparation . . 5 Preparation of the specimen 5 3.1Equipment . . 6 3.24 Test method . 6 5 Final measurements . 6 6 Details to be specified . . 7 BS EN 60512-9-2:20

22、1260512-9-2 IEC:2011 5 CONNECTORS FOR ELECTRONIC EQUIPMENT TESTS AND MEASUREMENTS Part 9-2: Endurance tests Test 9b: Electrical load and temperature 1 Scope and object This part of IEC 60512, when required by the detail specification, is used for testing connectors within the scope of technical comm

23、ittee 48. It may also be used for similar devices when specified in a detail specification. The object of this standard is to detail a standard test method to assess the ability of a connector to withstand elevated temperatures with electrical loading. 2 Normative references The following documents,

24、 in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60512-1-1, Connectors for e

25、lectronic equipment Tests and measurements Part 1-1: General examination Test 1a: Visual examination IEC 60512-1-100, Connectors for electronic equipment Tests and measurements Part 1-100: General Applicable publications IEC 60512-2-1, Connectors for electronic equipment Tests and measurements Part

26、2-1: Electrical continuity and contact resistance tests Test 2a: Contact resistance Millivolt level method IEC 60512-2-6, Connectors for electronic equipment Tests and measurements Part 2-6: Electrical continuity and contact resistance tests Test 2f: Housing (shell) electrical continuity IEC 60512-3

27、-1, Connectors for electronic equipment Tests and measurements Part 3-1: Insulation tests Test 3a: Insulation resistance IEC 60512-4-1, Connectors for electronic equipment Tests and measurements Part 4-1: Voltage stress tests Test 4a: Voltage proof 3 Preparation Preparation of the specimen 3.1The sp

28、ecimen shall be suitably fitted with temperature-sensing device(s) with dimensions as laid down in the detail specification, and be wired and mounted according to the detail specification. NOTE 1 Heat transfer by a measuring probe will influence the measurement. Care should be taken to limit this in

29、fluence, e.g. by using a non-intrusive measuring method. BS EN 60512-9-2:2012 6 60512-9-2 IEC:2011 NOTE 2 Attention is drawn to the fact that reproducibility is frequently improved by arranging the wiring horizontally. Equipment 3.2A suitable climatic chamber. Influence of the air circulation to the

30、 specimen shall be avoided. 4 Test method The specimen shall be subjected to a temperature endurance test with electrical load in accordance with the requirements of the detail specification. Initially (see note) and again at the end of the test, the insulation resistance at high temperature shall b

31、e measured according to IEC 60512-3-1, test 3a and shall be not less than the value specified by the detail specification. NOTE Due to the fact that specimen may be wired in series, an insulation resistance measurement after e.g. 10 h of exposure can be unpractical. In cases where such a measurement

32、 is possible, early failures will be detected, so that time-consuming testing can be avoided. The prepared specimen shall be placed in a chamber, the temperature of which shall be maintained at 70 % 5 % of the specified maximum operating temperature of the specimen under test. Current shall be appli

33、ed to the specimen and slowly increased until the specified maximum operating temperature (= ambient + temperature-rise due to current) is approached. There shall be no further increase of current before thermal stability is attained. In no case during the adjustment shall the specified maximum oper

34、ating temperature or the specified current of the specimen be exceeded. When the maximum operating temperature is reached, the current required to achieve this shall be maintained throughout the test. If the temperature rise due to the specified maximum current through the specimen does not cause it

35、 to reach its specified maximum operating temperature, the chamber temperature shall be increased until the specified maximum operating temperature of the specimen is reached. The test shall be carried out at the specified maximum operating temperature and the duration of the test shall be as specif

36、ied in the detail specification. Preferred durations are 250 h, 500 h, 1 000 h and 2 000 h. At the end of the exposure period, the specimen shall be allowed to cool under standard atmospheric conditions for a time as stated in the detail specification. If the maximum operating temperature of the spe

37、cimen is exceeded by 5 % under normal test conditions, the test shall be abandoned and the test shall be regarded as “failed“. 5 Final measurements a) Contact resistance (IEC 60512-2-1, test 2a, or IEC 60512-2-2, test 2b). b) Housing (shell) electrical continuity (IEC 60512-2-6, test 2f), where appl

38、icable. c) Insulation resistance (IEC 60512-3-1, test 3a). d) Voltage proof (IEC 60512-4-1, test 4a). e) Visual examination (IEC 60512-1-1, test 1a). f) Operational tests as required in the detail specification. NOTE If applicable, the detail specification may require a sealing test from the IEC 605

39、12-14 series or an ingress protection test according IEC 60529. BS EN 60512-9-2:201260512-9-2 IEC:2011 7 6 Details to be specified When this test is required by the detail specification, the following details shall be given: a) maximum operating temperature; b) duration; c) maximum load current; d)

40、insulation resistance (in hot condition); e) recovery time prior to final measurements; f) requirements for final measurements; g) any deviation from the standard test method. _ BS EN 60512-9-2:2012This page deliberately left blankThis page deliberately left blankBSI is the independent national body

41、 responsible for preparing British Standards and other standards-related publications, information and services. It presents the UK view on standards in Europe and at the international level. BSI is incorporated by Royal Charter. British Standards and other standardisation products are published by

42、BSI Standards Limited.British Standards Institution (BSI)raising standards worldwideBSI389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards and PASs are periodically updated by amendment or revision. Users of British Standards and PASs should make sure that the

43、y possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using British Standards would inform the Secretary of the technical committee responsible, the identi

44、ty of which can be found on the inside frontcover. Similary for PASs, please notify BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001BSI offers BSI Subscribing Members an individual updating service called PLUS which ensures that subscribers automatically receive the latest edi

45、tions of British Standards and PASs.Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001Email: Buying standardsYou may buy PDF and hard copy versions of standards directly using acredit card from the BSI Shop on the website addition all orders for BSI, international and foreign standards publicationsc

46、an be addressed to BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001Email: In response to orders for international standards, BSI will supply the British Standard implementation of the relevant international standard, unless otherwise requested.Information on standardsBSI provi

47、des a wide range of information on national, Europeanand international standards through its Knowledge Centre.Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005Email: BSI Subscribing Members are kept up to date with standards developments and receive substantial discounts on the purchase priceof stan

48、dards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards and PASs via British Standards Online can be found at information about British Standards is available on the BSI website at www.bsi- the data, software and documentation set out in all British Standards and other BSI publications are the property of and copyrighted by BSI, or some person or entity that own copyright in the information used (such