BS EN 60603-5-1998 Connectors for frequencies below 3 MHz for use with printed boards - Edge-socket connectors and two-part connectors for double-sided printed boards with 2 54 mm .pdf

1、BRITISH STANDARD BS EN 60603-5:1998 IEC60603-5: 1987 Connectors for frequencies below3MHz for use with printed boards Part 5: Edge-socket connectors and two-part connectors for double-sided printed boards with2,54mm(0,1 in) spacing The European Standard EN60603-5:1998 has the status of a British Sta

2、ndard ICS31.220.10BSEN 60603-5:1998 This British Standard, having been prepared under the directionof the Electrotechnical Sector Board, was published underthe authority of the Standards Board and comes intoeffect on 15 May1998 BSI05-1999 ISBN 0 580 29300 9 National foreword This British Standard is

3、 the English language version of EN60603-5:1998. It is identical with IEC60603-5:1987. The UK participation in its preparation was entrusted by Technical Committee EPL/48, Electromechanical components for electronic equipment, to Subcommittee EPL/48/2, Connectors for electronic equipment, which has

4、the responsibility to: aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UKinterests informed; monitor related international and European developments and promulgate them in the

5、 UK. A list of organizations represented on this subcommittee can be obtained on request to its secretary. From1 January1997, all IEC publications have the number60000 added to the old number. For instance, IEC27-1 has been renumbered as IEC60027-1. For a period of time during the change over from o

6、ne numbering system to the other, publications may contain identifiers from both systems. Cross-references Attention is drawn to the fact that CEN and CENELEC standards normally include an annex which lists normative references to international publications with their corresponding European publicat

7、ions. The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catal

8、ogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comp

9、rises a front cover, an inside front cover, pages i and ii, theEN title page, pages 2to 34 and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Amendments issued since

10、publication Amd. No. Date CommentsBSEN 60603-5:1998 BSI 05-1999 i Contents Page National foreword Inside front cover Foreword 2 Text of EN60603-5 3ii blankEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN60603-5 February 1998 ICS31.220.10 Descriptors: Electronic components, electric connectors, p

11、rinted-circuit cards, connector plugs, bed plates, designation, dimensions, assembling, couplings, tests, standard gauges, characteristics English version Connectors for frequencies below3MHz for use with printed boards Part5: Edge-socket connectors and two-part connectors for double-sided printed b

12、oards with2,54mm(0,1 in) spacing (IEC60603-5:1987) Connecteurs pour frquences infrieures3MHz pour utilisation aveccartesimprimes Partie5: Connecteurs encartables et connecteurs enfichables pour cartes imprimes double face au pas de2,54mm(0,1 in) (CEI60603-5:1987) Steckverbinder fr gedruckte Schaltun

13、gen fr Frequenzen unter3MHz Teil5: Steckverbinder fr direktes Stecken und indirekte Steckverbinder fr beidseitig-beschichtete leiterplatten mit2,54mm(0,1 in) Kontaktabstand (IEC60603-5:1987) This European Standard was approved by CENELEC on1998-01-01. CENELEC members are bound to comply with the CEN

14、/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to

15、any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official v

16、ersions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CENELEC European Committee for Elec

17、trotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B-1050 Brussels 1998 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No.

18、 EN60603-5:1998EEN60603-5:1998 BSI 05-1999 2 Foreword The text of the International Standard IEC60603-5:1987, prepared by SC48B, Connectors, of IEC TC48, Electromechanical components and mechanical structures for electronic equipment, was submitted to the formal vote and was approved by CENELEC as E

19、N60603-5 on1998-01-01 without any modification. The following dates were fixed: Annexes designated “normative” are part of the body of the standard. In this standard, Annex ZA is normative. Annex ZA has been added by CENELEC. Endorsement notice The text of the International Standard IEC60603-5:1987

20、was approved by CENELEC as a European Standard without any modification. Contents Page Foreword 2 1 Scope 3 2 IEC type designation 4 3 Common features 5 4 Dimensions 7 5 Gauges and test fixtures 18 6 Characteristics 25 7 Test schedule 26 Annex ZA (normative) Normative references tointernational publ

21、ications with their corresponding European publications 34 latest date by which the ENhas to be implemented at national level by publication of an identical national standard or by endorsement (dop) 1998-12-01 latest date by which the national standards conflicting with the EN have to be withdrawn (

22、dow) 1998-12-01EN60603-5:1998 BSI 05-1999 3 This standard shall be used in conjunction with IEC Publication 512: Electromechanical Components for Electronic Equipment: Basic Testing procedures and Measuring Methods. 1 Scope This standard covers a range of connectors with2.54mm(0.1 in) spacing intend

23、ed to connect a double sided printed board to another printed board or wires. Two kinds of connector are available: One-part edge-socket connector. Fixed connector or (female) receptacle is intended to mate with edge board contacts. Two-part connector. Fixed connector or (female) receptacle is inten

24、ded to mate with free connector of board-mounted (male) connector. For these two cases, fixed connectors or (female) receptacles are the same. Fixed connectors are available with: solder terminations for wire, solder terminations for board up to3.44mm(0.135 in), wrapped terminations. Free connectors

25、 are provided with flat solder terminations for double sided board of nominal thickness1.6mm(0.063 in). For edge-socket connectors only, polarization and coding are available by means of a device mounted instead of two opposite contacts.EN60603-5:1998 4 BSI 05-1999 2 IEC type designation Connectors

26、according to this publication shall be designated by: NOTE“L” for letter. “N” for number.EN60603-5:1998 BSI 05-1999 5 3 Common features 3.1 Isometric view 3.1.1 Edge-socket connectorEN60603-5:1998 6 BSI 05-1999 3.1.2 Two-part connectorEN60603-5:1998 BSI 05-1999 7 3.1.3 Common values 3.1.4 Values dep

27、ending on the number of contacts 3.2 Contact location The contact identification may be partial. It must be made on the front and rear faces for the fixed connectors and on the lateral face for the free connector. The fixed connector contacts may be replaced on the front face of the insulating housi

28、ng. 4 Dimensions 4.1 General Dimensions in millimetres are original. Drawings are shown in first angle projection. The shape of the connectors may deviate from those given in the following drawings as long as the specified dimensions are not influenced. Reference letter Dimensions Legend mm in a 1 2

29、.54 0.1 Pitch of the terminations of the fixed connector a 2 2.54 0.1 Pitch of the terminations of the free connector or of the contact pads of the double sided board b 1 5.08 0.2 Distance between two rows F 10.2min. 0.402min. Minimum width of mounting cut-out F 1 10max. 0.394max. Maximum overall wi

30、dth of the fixed connector H 2 14.8 0.583 Distance between the reference plane of the free connector and the touching face of board with free connector M 19.3 0.760 Distance between the mounting plane of the fixed connector and the touching face of board with free connector M 1 4.5 0.177 Distance be

31、tween the mounting plane of the fixed connector and the bottom of the board slot v 12.2 0.480 Minimum cut-out of the printed board Reference letter Legend C 1 Maximum overall length of the fixed connector C 2 Maximum overall length of the free connector f Minimum length of mounting cut-out N 2 Maxim

32、um length of the printed board in the area of the edge-board contacts X 1 Distance between the two mounting holes of the fixed connector X 2 Distance between the two mounting holes of the free connectorEN60603-5:1998 8 BSI 05-1999 4.2 Fixed connector 4.2.1 Insulating housingEN 60603-5:1998 BSI 05-19

33、99 9 A 1 B 1 D 1 F 1 K 1 M 1 a 1 b 1 c 1 d 1 e 1 g 1 h 1 mm 16 6,95 3,3 10 0,5 4,7 mm 2,54 5,08 2,05 5 1,8 5,8 1,1 14 6,75 3,2 max. 0,4 4,3 1,85 3,5 0,8 min. 0,9 in 0.630 0.274 0.130 0.394 0.020 0.185 in 0.1 0.2 0.081 0.197 0.071 0.228 0.043 0.531 0.266 0.126 max. 0.016 0.169 0.073 0.138 0.031 min.

34、0.035 Number of contacts 38 50 62 74 86 98 mm in mm in mm in mm in mm in mm in C 1 69 2.717 84,2 3.315 99,5 3.917 114,7 4.516 129,9 5.114 145,2 5.717 68 2.677 83,2 3.276 98,5 3.878 113,7 4.476 128,9 5.075 144,2 5.677 G 1 45,72 1.800 60,96 2.400 76,20 3.000 91,44 3.600 106,68 4.200 121,92 4.800 L 1 5

35、4,7 2.154 70 2.756 85,2 3.354 100,5 3.957 115,7 4.555 131 5.157 54,2 2.134 69,5 2.736 84,7 3.334 100 3.937 115,2 4.535 130,5 5.137 N 1 50,8 2.000 66,1 2.602 81,3 3.201 96,6 3.803 111,8 4.402 127 5.000 50,6 1.992 65,9 2.594 81,1 3.193 96,1 3.795 111,6 4.394 126,8 4.992 X 1 62,15 2.447 77,35 3.045 92,

36、65 3.648 107,85 4.246 123,05 4.844 138,35 5.447 61,85 2.435 77,05 3.033 92,35 3.636 107,55 4.234 122,75 4.832 138,05 5.435 f 1 48,4 1.906 63,64 2.506 78,88 3.106 94,12 3.706 109,36 4.306 124,60 4.906 min. min. min. min. min. min. min. min. min. min. min. min.EN60603-5:1998 10 BSI 05-1999 4.2.2 Termi

37、nations of fixed connector C=for solder termination for wire Eyelet solder terminations enable the connection of a wire, the conductor of which has a maximum diameter of0.55mm(0.022 in). W=for wrapped terminations Wrap posts enable the connection of wires, the conductor of which has a diameterof0.25

38、mm(0.010 in),0.32mm(0.013 in) or0.4mm(0.016 in) on three levels. The cross-section of the wrap post shall have a diagonal between0.78mm(0.039 in) and0.89mm(0.035 in). Y=for solder terminations for printed board The cross-section of the terminations shall enable its insertion into the holes of the bo

39、ard specified in Sub-clause4.6.2. mm in T 1 5,5 4,5 0.217 0.177 mm in S 1 13,2 min. 0.520 min. U 1 16 15 0.630 0.591 mm in S 1 3.5 min. 0.138 min. V 1 5 4 0.197 0.157EN60603-5:1998 BSI 05-1999 11 4.3 Free connectorEN 60603-5:1998 12 BSI 05-1999 A 2 B 2 D 2 E 2 F 2 H 2 mm 12 11,7 3,1 2,9 2,8 2,6 6,5

40、4,5 0,5 5,5 15,1 14,5 in 0.472 0.461 0.122 0.114 0.110 0.102 0.256 0.177 0.335 0.217 0.594 0.571 a 2 c 2 d 2 e 2 g 2 m 2 n 2 P 2 q 2 r 2 S 2 mm 2,54 1,8 3,5 0,8 10 3,0 1,55 5 2,05 3,5 1,6 1,4 max. max. min. max. 1,35 max. 1,85 1 in 0.1 0.071 0.138 0.031 0.394 0.118 0.061 0.197 0.081 0.138 0.063 0.05

41、5 max. max. min. max. 0.053 max. 0.073 0.040EN 60603-5:1998 BSI 05-1999 13 Number of contacts 38 50 62 74 86 98 mm in mm in mm in mm in mm in mm in C 2 62,58 2.464 77,82 3.064 93,06 3.664 108.3 4.264 123,54 4.864 138,78 5.464 61,58 2.424 76,82 3.024 92,06 3.624 107.3 4.244 122,54 4.824 137,78 5.424

42、G 2 45,72 1.800 60,96 2.400 76,20 3.000 91,44 3.600 106,68 4.200 121,92 4.800 N 2 50,5 1.988 65,8 2.591 81 3.189 96,3 3.791 111,5 4.390 126,7 4.988 50,3 1.980 65,6 2.583 80,8 3.181 96,1 3.783 111,3 4.382 126,5 4.980 X 2 56,08 2.208 71,32 2.808 86,56 3.408 101,80 4.008 117,04 4.608 132,28 5.208 55,68

43、 2.192 70,92 2.792 86,16 3.392 101,40 3.992 116,64 4.592 131,88 5.192 f 2 50 1.969 65,24 2.569 80,48 3.169 95,72 3.769 110,96 4.369 126,2 4.969 47,50 1.870 62,74 2.470 77,98 3.070 93,22 3.670 108,46 4.270 123,70 4.870 NOTE 1Dimension on insert dimension on contacts. NOTE 2Security of insertion accor

44、ding to reference plan. NOTE 3The contact tails shall ensure a sufficient pressure on the board of nominal thickness1.6mm(0.063 in) and will be tin-soldered before insertion.EN60603-5:1998 14 BSI 05-1999 4.4 Mating information The free connector must bottom on the board slot of the fixed connector.

45、4.5 Polarizing and coding For edge-socket connector only, the polarization can be provided by replacing two opposite contacts of the fixed connector by a polarizing key. A slot shall then be provided in the board to receive it. The place of the polarizing key shall be selected by the user. 4.6 Mount

46、ing 4.6.1 Fixed connectors mounted on panel mm in M 19,8 18,8 0.780 0.740 F ? D mm 10,2min. 3,4 3,2 in 0.402min. 0.134 0.126 Number of contacts 38 50 62 74 86 98 mm in mm in mm in mm in mm in mm in X 1 62 2.441 77,2 3.039 92,5 3.642 107,7 4.240 122,9 4.839 138,2 5.441 f 56,4 min. 2.220 min. 71,6 min

47、. 2.819 min. 86,9 min. 3.421 min. 102.1 min. 4.020 min. 117,3 min. 4.618 min. 132,6 min. 5.220 min.EN60603-5:1998 BSI 05-1999 15 4.6.2 Fixed connectors mounted on board a ? D ? V mm 2,54 3,1 3,4 0,8min. in 0.1 0.131 0.135 0.031min. Number of contacts 38 50 62 74 86 98 mm in mm in mm in mm in mm in m

48、m in G 45,72 1.800 60,96 2.400 76,20 3.000 91,44 3.600 106,68 4.200 121,92 4.800 X 1 62 2.441 77,2 3.039 92,5 3.642 107,7 4.240 122,9 4.839 138,2 5.441EN60603-5:1998 16 BSI 05-1999 4.6.3 Cut-out of the board used with edge-socket connector a e n t U V mm 2,54 1,78 1,42 1,7 1,5 1,7 1,5 0,5 max. 12,2

49、min. in 0.1 0.070 0.055 0.067 0.059 0.067 0.059 0.020 max. 0.480 min. Number of contacts 38 50 62 74 86 98 mm in mm in mm in mm in mm in mm in G 2 45,72 1.800 60,96 2.400 76,20 3.000 91,44 3.600 106,68 4.200 121,92 4.800 N 2 50,5 50,3 1.988 1.980 65,8 65,6 2.591 2.583 81 80,8 3.189 3.181 96,3 96,1 3.791 3.783 111,5 111,3 4.390 4.382 126,7 126,5 4.988 4.980EN60603-5:1998 BSI 05-1999 17 4.7 Board used with free connector a e n U B 1 F ? D mm 2,54 1,78 1,42 1,7 1,5 0,5 max. 3,1 2,9 10 min. 3 2,8 in 0.1 0.070 0.055 0.067