BS EN 60684-3-283-2010 Flexible insulating sleeving Specifications for individual types of sleeving Heat-shrinkable polyolefin sleeving for bus-bar insulation《挠性绝缘套管 各种型号套管的规范 母线绝缘.pdf

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationFlexible insulating sleevingPart 3: Specifications for individual types of sleevingSheet 283: Heat-shrinkable, polyolefin sleeving, for bus-bar insulationBS EN 60684-3-283:2011Li

2、censed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 21/04/2011 09:02, Uncontrolled Copy, (c) BSINational forewordThis British Standard is the UK implementation of EN 60684-3-283:2011. It isidentical to IEC 60684-3-283:2010.The UK participation in its preparation was entrusted by Technical Committee

3、GEL/15, Solid electrical insulating materials, to Subcommittee GEL/15/5,Flexible insulating sleeving for electrical purposes.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisions of a

4、contract. Users are responsible for its correct application. BSI 2011ISBN 978 0 580 65792 4ICS 29.035.20Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of the StandardsPolicy and Strategy Committee on 28 February

5、 2011.Amendments issued since publicationAmd. No. Date Text affectedBRITISH STANDARDBS EN 60684-3-283:2011Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 21/04/2011 09:02, Uncontrolled Copy, (c) BSIEUROPEAN STANDARD EN 60684-3-283 NORME EUROPENNE EUROPISCHE NORM January 2011 CENELEC European

6、Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Management Centre: Avenue Marnix 17, B - 1000 Brussels 2011 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC

7、 members. Ref. No. EN 60684-3-283:2011 E ICS 29.035.20 English version Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 283: Heat-shrinkable, polyolefin sleeving, for bus-bar insulation (IEC 60684-3-283:2010) Gaines isolantes souples - Partie 3: Spcifica

8、tions pour types particuliers de gaines - Feuille 283: Gaines thermortractables en polyolfine pour isolation de barre omnibus (CEI 60684-3-283:2010) Isolierschluche - Teil 3: Anforderungen fr einzelne Schlauchtypen - Blatt 283: Polyolefin-Wrmeschrumpfschluche fr die Isolierung von Sammelschienen (IE

9、C 60684-3-283:2010) This European Standard was approved by CENELEC on 2011-01-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists

10、and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the resp

11、onsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Franc

12、e, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. BS EN 60684-3-283:2011Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 21/04/20

13、11 09:02, Uncontrolled Copy, (c) BSIEN 60684-3-283:2011 - 2 - Foreword The text of document 15/597/FDIS, future edition 1 of IEC 60684-3-283, prepared by IEC TC 15, Solid electrical insulating materials, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 60684-3-283 on

14、2011-01-01. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and CENELEC shall not be held responsible for identifying any or all such patent rights. The following dates were fixed: latest date by which the EN has to be impleme

15、nted at national level by publication of an identical national standard or by endorsement (dop) 2011-10-01 latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 2014-01-01 Annex ZA has been added by CENELEC. _ Endorsement notice The text of the International

16、Standard IEC 60684-3-283:2010 was approved by CENELEC as a European Standard without any modification. _ BS EN 60684-3-283:2011Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 21/04/2011 09:02, Uncontrolled Copy, (c) BSI- 3 - EN 60684-3-283:2011 Annex ZA (normative) Normative references to int

17、ernational publications with their corresponding European publications The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any

18、 amendments) applies. NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. Publication Year Title EN/HD Year IEC 60296 2003 Fluids for electrotechnical applications - Unused mineral insulating oils for transformers and swit

19、chgear EN 60296 + corr. September 2004 2004 IEC 60684-1 2003 Flexible insulating sleeving - Part 1: Definitions and general requirements EN 60684-1 2003 IEC 60684-2 + A1 + A2 1997 2003 2005 Flexible insulating sleeving - Part 2: Methods of test EN 60684-2 + A1 + A2 1997 2003 2005 IEC 60757 1983 Code

20、 for designation of colours HD 457 S1 1985 ISO 846 1997 Plastics - Evaluation of the action of microorganisms EN ISO 846 1997 ISO 4892-3 2006 Plastics - Methods of exposure to laboratory light sources - Part 3: Fluorescent UV lamps EN ISO 4892-3 2006 BS EN 60684-3-283:2011Licensed Copy: Wang Bin, IS

21、O/EXCHANGE CHINA STANDARDS, 21/04/2011 09:02, Uncontrolled Copy, (c) BSI 2 60684-3-283 IEC:2010 CONTENTS INTRODUCTION 5 1 Scope 6 2 Normative references 6 3 Designation 7 4 Conditions of test . 7 5 Requirements . 7 6 Sleeving conformance . 7 Annex A (informative) Guidance to the available sizes and

22、wall thicknesses 11 Table 1 Property requirements 8 Table 2 Requirements for dielectric strength . 9 Table 3 Resistance to selected fluids . 9 Table 4 Additional property requirements . 10 Table A.1 Type A, medium wall . 11 Table A.2 Type B, thick wall 11 BS EN 60684-3-283:2011Licensed Copy: Wang Bi

23、n, ISO/EXCHANGE CHINA STANDARDS, 21/04/2011 09:02, Uncontrolled Copy, (c) BSI60684-3-283 IEC:2010 5 INTRODUCTION This International Standard is one of a series which deals with flexible insulating sleeving for electrical purposes. The series consists of three parts: Part 1: Definitions and general r

24、equirements (IEC 60684-1) Part 2: Methods of test (IEC 60684-2) Part 3: Specifications for individual types of sleeving (IEC 60684-3) This standard comprises one of the sheets of Part 3: Sheet 283: Heat-shrinkable, polyolefin sleeving for bus-bar insulation. BS EN 60684-3-283:2011Licensed Copy: Wang

25、 Bin, ISO/EXCHANGE CHINA STANDARDS, 21/04/2011 09:02, Uncontrolled Copy, (c) BSI 6 60684-3-283 IEC:2010 FLEXIBLE INSULATING SLEEVING Part 3: Specifications for individual types of sleeving Sheet 283: Heat-shrinkable, polyolefin sleeving for bus-bar insulation 1 Scope This part of IEC 60684 gives the

26、 requirements for two types of heat-shrinkable, polyolefin sleeving for bus-bar insulation, with a nominal shrink ratio of 2,5:1. This sleeving has been found suitable up to temperatures of 100 C. Type A : Medium wall Internal diameter up to 170,0 mm typically Type B : Thick wall Internal diameter u

27、p to 165,0 mm typically These sleevings are normally supplied in colour, red or brown. Since these types of sleevings cover a significantly large range of sizes and wall thicknesses, Tables A.1 and A.2 provide guidance to the range of sizes available. The actual size and wall thickness shall be agre

28、ed between the user and supplier depending on the electric strength of the installed tubing offered and the requirements of the user. Materials which conform to this specification meet established levels of performance. However, the selection of a material by a user for a specific application should

29、 be based on the actual requirements necessary for adequate performance in that application and not based on this specification alone. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applie

30、s. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60296:2003, Fluids for electrotechnical applications Unused mineral insulating oils for transformers and switchgear IEC 60684-1:2003, Flexible insulating sleeving Part 1: Definitions and

31、general requirements IEC 60684-2:1997, Flexible insulating sleeving Part 2: Methods of test Amendment 1 (2003) Amendment 2 (2005) IEC 60757:1983, Code for designation of colours ISO 846:1997, Plastics Evaluation of the action of microorganisms ISO 4892-3:2006, Plastics Methods of exposure to laborat

32、ory light sources Part 3: Fluorescent UV lamps BS EN 60684-3-283:2011Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 21/04/2011 09:02, Uncontrolled Copy, (c) BSI60684-3-283 IEC:2010 7 3 Designation The sleeving shall be identified by the following designation: Description IEC publication numb

33、er IEC part number IEC sheet number Type Size (expanded and recovered internal diameter in millimetres) Colour Table 4acode Sleeving IEC 60684 - 3 -283 A - 75,0/30,0 -Red X aThe addition of “X” at the end of the designation indicates that the properties contained in Table 4 have been agreed upon bet

34、ween the user and the supplier. Any colour abbreviation shall comply with IEC 60757, where applicable. Non-standard colours shall be written out in full. NOTE This is for package labelling only in accordance with IEC 60684-1. 4 Conditions of test Unless otherwise specified, the sleeving shall be shr

35、unk in a forced air circulation oven for (10 1) min at 200 C 3 K prior to testing. 5 Requirements In addition to the general requirements given in IEC 60684-1, the sleeving shall comply with the requirements of Tables 1, 2, 3, and 4 where applicable. 6 Sleeving conformance Conformance to the require

36、ments of this specification shall normally be based on the results from typical sizes. Type A : Recovered ID 25 mm - 30 mm Type B : Recovered ID 25 mm - 40 mm BS EN 60684-3-283:2011Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 21/04/2011 09:02, Uncontrolled Copy, (c) BSI 8 60684-3-283 IEC:2

37、010 Table 1 Property requirements Property IEC 60684-2 clause or subclause Units Max. or min. Requirements Remarks Dimensions Internal diameter Wall thickness Concentricity expanded recovered 3 3.1.2 3.3.2 3.3.3 mm mm % Min. Min. To be agreed between the purchaser and the supplier 60 85 Heat shock T

38、ensile strength Elongation at break 6 19.1 and 19.2 19.1 and 19.2 MPa % Min. Min. 5 200 Heat at 150 C 5 K Longitudinal change 9 % Max. 10 +5 Bending at low temperature 14 No cracking shall be visible. Test at 40 C For strips, the mandrel shall be between 20 and 22 times the wall thickness. Full sect

39、ion sleeving is tested unfilled and the mandrel shall be between 20 and 22 times the outer diameter. Dimensional stability on storage 16 The dimensions shall remain as agreed. See Scope. Tensile strength Elongation at break 19.1 and 19.2 19.1 and 19.2 MPa % Min. Min. 8 400 Use a jaw separation rate

40、of 100 mm/min. Secant modulus at 2 % elongation 19.4 MPa Max. 160 Dielectric strength 21 kV/mm Min. See Table 2. Volume resistivity at room temperature 23 23.4.2 m Min. 1011 Flame propagation 26 Method C s mm Max. Max. 60 100 Burning includes flaming and glowing Corrosion resistance Elongation 32 19

41、.1 and 19.2 % Min. No chemical interaction Heat at 150 C 3 K Resistance to selected fluids Tensile strength Elongation at break 36 19.1 and 19.2 19.1 and 19.2 MPa % Min. Min. 5 200 Use the fluids and test temperatures specified in Table 3. Immersion (24 1)h Heat ageing Tensile strength Elongation at

42、 break 39 19.1 and 19.2 19.1 and 19.2 MPa % Min. Min. 5 200 Heat at 150 C 3 K Long term ageing Elongation at break 50 19.2 % Min. 150 The ageing temperature shall be 100 C 3 K. BS EN 60684-3-283:2011Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 21/04/2011 09:02, Uncontrolled Copy, (c) BSI60

43、684-3-283 IEC:2010 9 Table 2 Requirements for dielectric strength Expanded wall thickness mm Dielectric strength a Min. All dimensions Expanded ID Types A+B All sizes Dielectric strength kV/mm 12 aMeasure the expanded wall thickness and calculate the electric strength by dividing the breakdown volta

44、ge by this value. NOTE Care should be taken on selection of sizes based on these values. Refer to the manufacturer for actual values on installed conditions. The breakdown voltage shall be determined by the method described in 21 of IEC 60684-2. All values shall comply with the minimum value in this

45、 table. The sleeving shall be tested in the expanded condition. The rate of application of the voltage shall be 500 V/s. Table 3 Resistance to selected fluids Test fluid No. Fluids Type Standard or symbol Immersion temperature C 2 K 1 Insulating oil Mineral based IEC 60296 23 2 Cleaning fluid Solven

46、t Isopropyl alcohol 23 3 - Water De-ionized 85 Other fluids and/or temperatures may be specified for customers with specific needs. These additional fluids and/or temperatures shall be applicable when incorporated into agreements between the supplier and the customer. BS EN 60684-3-283:2011Licensed

47、Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 21/04/2011 09:02, Uncontrolled Copy, (c) BSI 10 60684-3-283 IEC:2010 Table 4 Additional property requirements Property IEC 60684-2 Units Max. or min. Requirement Remarks Fungus resistance Tensile strength Elongation 19.1 and 19.2 MPa % Min. Min. 7 350 Th

48、e test method shall be ISO 846 Method B 56 days exposure Resistance to weathering ISO 4892-3 (Method 1) After 5 000 h test to 19.1 19.2 25 MPa % Min. Min. Min. 8 200 2,5 kV for 20 min Test method to ISO 4892-3 Samples for test 19.1 and 19.2 should be taken from recovered sleeving which is flattened.

49、 Samples for Test 25 should be taken from specially prepared test sheets (6 0,1) mm thick. All samples should be cut to the appropriate size to fit the sample holders. Intermediate tests may also be done at 1000 h intervals as an intermediate check on performance. Resistance to tracking 25 Min. Class 2A 2,5 kV for 1 h Specimens shall be prepared from cross-linked moulded plaques of thicknes