BS EN 60684-3-340 to 342-2003 Specification for flexible insulating sleeving - Specification requirements for individual types of sleeving - Expandable braided polyethylene terepht.pdf

1、BRITISH STANDARD BS EN 60684-3-340 to 342:2003 Flexible insulating sleeving Part 3: Specifications for individual types of sleeving Sheets 340 to 342: Expandable braided polyethylene terephthalate textile sleeving The European Standard EN 60684-3-340 to 342:2003 has the status of a British Standard

2、ICS 29.035.20 BS EN 60684-3-340 to 342:2003 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 22 August 2003 BSI 22 August 2003 ISBN 0 580 42489 8 National foreword This British Standard is the official English language version of EN 60684-3-34

3、0 to 342:2003. It is identical with IEC 60684-3-340 to 342:2003. It supersedes BS EN 60684-3-340 to 342:1994 which is withdrawn. The UK participation in its preparation was entrusted by Technical Committee GEL/15, Insulating material, to Subcommittee GEL/15/3, Material specifications, which has the

4、responsibility to: A list of organizations represented on this subcommittee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Catalogue under the section enti

5、tled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Complianc

6、e with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related int

7、ernational and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 10, an inside back cover and a back cover. The BSI copyright date displayed in this document indicates when the document wa

8、s last issued. Amendments issued since publication Amd. No. Date CommentsEUROPEAN STANDARD EN 60684-3-340 to 342 NORME EUROPENNE EUROPISCHE NORM July 2003 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotec

9、hnische Normung Central Secretariat: rue de Stassart 35, B - 1050 Brussels 2003 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 60684-3-340 to 342:2003 E ICS 29.035.20 Supersedes EN 60684-3-340 to 342:1994English version Flexible

10、insulating sleeving Part 3: Specifications for individual types of sleeving Sheets 340 to 342: Expandable braided polyethylene terephthalate textile sleeving (IEC 60684-3-340 to 342:2003) Gaines isolantes souples Partie 3: Spcifications pour types particuliers de gaines Feuilles 340 342: Gaines expa

11、nsibles tresses de trphtalate de polythylne (CEI 60684-3-340 342:2003) Isolierschluche Teil 3: Bestimmungen fr einzelne Schlauchtypen Bltter 340 bis 342: Aufweitbare, geflochtene Polyethylenterephthalat- Textilschluche (IEC 60684-3-340 bis 342:2003) This European Standard was approved by CENELEC on

12、2003-07-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may

13、be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to t

14、he Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Lithuania, Luxembourg, Malta, Netherlands, Norway, Portu

15、gal, Slovakia, Spain, Sweden, Switzerland and United Kingdom. Foreword The text of document 15C/1466/FDIS, future edition 2 of IEC 60684-3-340 to 342, prepared by SC 15C, Specifications, of IEC TC 15, Insulating materials, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as

16、 EN 60684-3-340 to 342 on 2003-07-01. This European Standard supersedes EN 60684-3-340 to 342:1994. The following dates were fixed: latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2004-04-01 latest date by w

17、hich the national standards conflicting with the EN have to be withdrawn (dow) 2006-07-01 Annexes designated “normative“ are part of the body of the standard. In this standard, annex ZA is normative. Annex ZA has been added by CENELEC. _ Endorsement notice The text of the International Standard IEC

18、60684-3-340 to 342:2003 was approved by CENELEC as a European Standard without any modification. _ 2egaP EN606843340to342Page2 EN606843340to342:2003-48606-3243 ot 043 3002:CEI 3 CONTENTS INTRODUCTION.4 1 Scope.5 2 Normative references5 3 Designation6 4 Requirements.6 4.1 Standard requirements 6 4.2

19、Special requirements .6 5 Product conformance6 Annex ZA (normative) Normative references to international publications with their corresponding European publications10 Table 1 Dimensional requirements7 Table 2 Standard requirements.8 Table 3 Requirements for tensile strength.8 Table 4 Resistance to

20、selected fluids9 Table 5 Special requirements .9 Pa3eg EN606843340to342Page3 EN606843340to342:2003-48606-3243 ot 043 3002:CEI 4 INTRODUCTION This International Standard is one of a series which deals with flexible insulating sleeving for electrical purposes. The series consists of three parts: Part

21、1: Definitions and general requirements (IEC 60684-1); Part 2: Methods of test (IEC 60684-2); Part 3: Specifications for individual types of sleeving (IEC 60684-3). This standard contains three of the sheets comprising Part 3, as follows: Sheet 340: Expandable braided polyethylene terephthalate text

22、ile sleeving, uncoated, general purpose, thin wall thickness; Sheet 341: Expandable braided polyethylene terephthalate textile sleeving, uncoated, general purpose, medium wall thickness; Sheet 342: Expandable braided polyethylene terephthalate textile sleeving, uncoated, general purpose, thick wall

23、thickness. Pa4eg EN606843340to342Page4 EN606843340to342:2003-48606-3243 ot 043 3002:CEI 5 FLEXIBLE INSULATING SLEEVING Part 3: Specifications for individual types of sleeving Sheets 340 to 342: Expandable braided polyethylene terephthalate textile sleeving 1 Scope This standard gives the requirement

24、s for sleeving having the property of expanding its internal diameter when compressed longitudinally and thereafter returning to its initial diameter after release of the compressing force. It is constructed of polyethylene terephthalate monofilament yarns suitably processed to provide the mechanica

25、l ability to conform in the manner described above. These sleevings have been found suitable for use at temperatures up to 130 C. This sleeving is normally supplied in internal diameters between 6 mm and 63 mm and in three levels of wall thickness (thin, medium, and thick). It is normally supplied i

26、n the following colours: black, white, brown, red, orange, yellow, green, blue, grey, and natural. Because of its open construction, this sleeving is normally used to provide air-space insulation. Therefore, no requirement for breakdown voltage is specified in this standard. (Any value for this prop

27、erty should be given in the purchase contract, but a typical value is 1,5 kV/mm wall thickness, although a linear relationship cannot be assumed.) However, it serves to provide mechanical protection to circuit components such as wires, sleeves, and flat cable over which it is applied as a containing

28、 wrap or harness. Materials which conform to this specification meet established levels of performance. However, the selection of a material by a user for a specific application should be based on the actual requirements necessary for adequate performance in that application and not based on this sp

29、ecification alone. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 606

30、84-1:1980, Specification for flexible insulating sleeving Part 1: Definitions and general requirements IEC 60684-2:1997, Flexible insulating sleeving Part 2: Methods of test IEC 60757:1983, Code for designation of colours ISO 846:1997, Plastics Evaluation of the action of micro-organisms ISO 1817:19

31、99, Rubber, vulcanized Determination of the effect of liquids Page5 EN606334840to342Page5 EN606843340to342:2003-48606-3243 ot 043 3002:CEI 6 3 Designation The sleeving shall be identified by the following designation: Sleeving IEC 60684 -3 -340 -6 -NC X Description IEC publication number IEC part nu

32、mber IEC sheet number Size. Internal diameter in mm Colour Require- ments from Table 5 are applicable The addition of “X” at the end of the designation indicates that either or both of the properties contained in Table 5 have been agreed and are included in the purchase contract. Any abbreviation us

33、ed for colour shall comply with IEC 60757. NC is used for “Natural Colour / No Colour pigmentation”. Where no abbreviation is given, the colour shall be written in full. 4 Requirements 4.1 Standard requirements In addition to the general requirements given in IEC 60684-1, the sleeving in the sizes n

34、ormally available shall comply with the requirements in Tables 1 and 2. 4.2 Special requirements If sleeving is to be supplied with any of the properties specified in Table 5, it shall also comply with the appropriate requirements of Table 5. 5 Product conformance Conformance with the requirements o

35、f this specification shall normally be based on the results of size 32 mm sleeving. Page6 EN606843t043o342Page6 EN606843340to342:2003-48606-3243 ot 043 3002:CEI 7 Table 1 Dimensional requirements Nominal internal diameter mm Minimum internal diameter in fully expanded state (by longitudinal compress

36、ion) mm 6 9 10 15 12 19 16 27 20 34 30 42 32 45 40 62 45 70 50 89 60 107 63 114 Sheet 340: Thin wall 0,30 mm min. Sheet 341: Medium wall 0,50 mm min. Wall thicknesses Sheet 342: Thick wall 0,75 mm min. Wall thickness dimensions shall be measured to the nearest 0,05 mm, using the suitable method of C

37、lause 3 in IEC 60684-2. Because of the ease with which this sleeving can be dilated, care should be exercised in measuring the internal diameter using the plug gauges described in 3.1 of IEC 60684-2. Pa7eg EN606843340to342Page7 EN606843340to342:2003-48606-3243 ot 043 3002:CEI 8 Table 2 Standard requ

38、irements Property IEC 60684-2 clause or subclause Units Min. or Max. Requirement Remarks Dimensions 3 mm Min. Table 1 Longitudinal change 9 % Max. +10 Test specimens shall be conditioned for 4 h at 175 C 2 K Bending at low temperature 14 No cracking Full-section test specimens shall be conditioned u

39、nfilled at 70 C 5 K and tested by bending at that temperature around a 25 mm diameter metal rod Tensile strength 19.1 aN Min. Table 3 Resistance to fluids 36 19.1 a% Min. 90 % min. retention of maximum load at break Use the fluids and test temperatures specified in Table 4 aThe central value shall b

40、e reported as the maximum load at break. The jaws shall be separated at a uniform rate of 100 mm/min. Table 3 Requirements for tensile strength Nominal internal diameter mm Thin wall Sheet 340 N Medium wall Sheet 341 N Thick wall Sheet 342 N 6 10 12 16 20 30 32 40 45 50 60 63 680 910 1 060 1 170 1 2

41、60 1 660 1 700 1 950 2 010 2 210 2 430 2 500 1 120 1 500 1 760 1 900 2 110 2 750 2 840 3 250 3 500 3 680 4 100 4 160 1 690 2 260 2 650 2 900 3 160 4 100 4 260 4 800 5 150 5 510 6 000 6 250 Page8 606NE843340to342Page8 EN606843340to342:2003-48606-3243 ot 043 3002:CEI 9 Table 4 Resistance to selected f

42、luids Test fluid no. Fluid Type Standard or symbol Immersion temperature C 2 K 1 Gasoline ISO 1817 Liquid B 23 2 Fuels Kerosene ISO 1817 Liquid F 23 3 Phosphate base ISO 1817 Liquid 103 23 4 Silicone base S-1714 a23 5 Hydraulic fluids Mineral base H-520 a23 6 Synthetic base ISO 1817 Liquid 101 23 7

43、Mineral base ISO 1817 Oil no. 2 23 8 Mineral base O-1176 a23 9 Oils Mineral base O-142 a23 10 Isopropyl alcohol 23 11 Propanol 25 % White spirit 75 % 23 12 Cleaning fluids Solvent Methylethylketone 23 13 Runway de-icers Inhibited potassium acetate in water, 50 % 23 14 De-icing fluids Aircraft de-ice

44、rs Ethylene glycol 80 % Water 20 % 23 Other fluids and/or temperatures may be specified with specific needs. These additional fluids shall be applicable when incorporated into agreements between the supplier and customer. aThese are commercially available fluids which can be identified in aviation f

45、luid guides.Table 5 Special requirements Property IEC 60684-2 clause or subclause or other reference Max. or Min. Requirements Remarks Mould growth ISO 846, Method A Max. Scale 1 or better Fraying resistance 20 Max. Shall be subject to purchase contract _ Pa9eg EN606843340to342Page9 EN606843340to342

46、:2003 Annex ZA (normative) Normative references to international publications with their corresponding European publications This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the te

47、xt and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to appli

48、es (including amendments). NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. Publication Year Title EN/HD Year IEC 60684-1 1980 Specification for flexible insulating sleeving Part 1: Definitions and general requirements EN 60684-1 1995 1)IEC 60684-2 1997 Flexible insulating sleeving Part 2: Methods of test EN 60684-2 1997 IEC 60757 1983 Code for designation of colours HD 457 S1 1985 ISO 846 1997 Plastics - Evaluation of the action of microorganisms EN ISO 846 1997 ISO 1