BS EN 60939-2-2005 Passive filter units for electromagnetic interference suppression - Sectional specification passive filter units for which safety tests are appropriate - Test me.pdf

1、 g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58suppression Part 2: Sectional specification: Passive filter units for which safety tests are approp

2、riate Test methods and general requirements The European Standard EN 60939-2:2005 has the status of a British StandardICS 31.160Passive filter units for electromagnetic interference BRITISH STANDARDBS EN 60939-2:2005Incorporating Corrigendum No. 1BS EN 60939-2:2005This British Standard was published

3、 under the authority of the Standards Policy and Strategy Committee on 19 August 2005 BSI 2006ISBN 0 580 46032 0A list of organizations represented on this committee can be obtained on request to its secretary.Cross-referencesThe British Standards which implement international or European publicatio

4、ns referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online.This publication does not purport to include all the necessary

5、 provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard does not of itself confer immunity from legal obligations.enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and Eu

6、ropean developments and promulgate them in the UK.Summary of pagesThis document comprises a front cover, an inside front cover, the EN title page, pages 2 to 46, an inside back cover and a back cover.The BSI copyright notice displayed in this document indicates when the document was last issued.Amen

7、dments issued since publicationAmd. No. Date Comments16255 Corrigendum No. 131 August 2006 See national forewordThe UK participation in its preparation was entrusted to Technical Committee EPL/40X, Capacitors and resistors for electronic equipment, which has the responsibility to: aid enquirers to u

8、nderstand the text; present to the responsible international/European committee any National forewordThis British Standard is the official English language version of EN 60939-2:2005. It is identical with IEC 60939-2:2005, including corrigendum November 2005. It supersedes BS EN 133200:1999 which wi

9、ll be withdrawn on 1 March 2008.The start and finish of text introduced or altered by corrigendum is indicated in the text by tags . Tags indicating changes to IEC text carry the number of the corrigendum. For example, text altered by IEC corrigendum 1 is indicated in the text by .EUROPEAN STANDARD

10、EN 60939-2 NORME EUROPENNE EUROPISCHE NORM April 2005 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B - 1050 Brussels ICS 31.160 Supersedes EN 1

11、33200:1999English version Passive filter units for electromagnetic interference suppression Part 2: Sectional specification: Passive filter units for which safety tests are appropriate Test methods and general requirements (IEC 60939-2:2005) Filtres passifs dantiparasitage Partie 2: Spcification int

12、ermdiaire: Filtres passifs pour lesquels des essais de scurit sont appropris Mthodes dessai et rgles gnrales (CEI 60939-2:2005) Passive Filter fr die Unterdrckung von elektromagnetischen Strungen Teil 2: Rahmenspezifikation: Filter, fr die Sicherheitsprfungen vorgeschrieben sind Prfverfahren und all

13、gemeine Anforderungen (IEC 60939-2:2005) This European Standard was approved by CENELEC on 2005-03-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterati

14、on. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by trans

15、lation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,

16、 Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. 2005 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC me

17、mbers. Ref. No. EN 60939-2:2005 E EN 60939-2:2005 - 2 - Foreword The text of document 40/1510/FDIS, future edition 2 of IEC 60939-2, prepared by IEC TC 40, Capacitors and resistors for electronic equipment, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 60939-2 on 2

18、005-03-01. This European Standard supersedes EN 133200:1999. The following dates were fixed: latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2005-12-01 latest date by which the national standards conflicting

19、 with the EN have to be withdrawn (dow) 2008-03-01 Annex ZA has been added by CENELEC. _ Endorsement notice The text of the International Standard IEC 60939-2:2005 was approved by CENELEC as a European Standard without any modification. _ 3 EN 60939-2:2005 CONTENTS 1 General7 1.1 Scope7 1.2 Normativ

20、e references 7 1.3 Information to be given in a detail specification 8 1.3.1 General .8 1.3.2 Outline drawing and dimensions.8 1.3.3 Mounting8 1.3.4 Ratings and characteristics 9 1.3.5 Marking .9 1.4 Terms and definitions 9 1.5 Marking .10 1.5.1 See 2.4 of IEC 60939-1 with the following details:.10

21、1.5.2 The filter shall be clearly marked with the information in 1.5.1 a), b), c), d) and f), and also e) if this is not implied by b). .11 1.5.3 The package containing the filter(s) shall be clearly marked with all the information listed in 1.5.1. 11 1.5.4 Any additional marking shall be so applied

22、 that no confusion can arise. .11 2 Preferred ratings and characteristics.11 2.1 Preferred characteristics11 2.1.1 General .11 2.1.2 Preferred climatic categories 11 2.2 Preferred values of ratings.11 2.2.1 Rated voltage (UR).11 2.2.2 Category voltage (UC) 11 2.2.3 Rated temperature .12 2.2.4 Passiv

23、e flammability 12 3 Quality assessment procedures 12 3.1 Primary stage of manufacture 12 3.2 Structurally similar filters .12 3.3 Certified records of released lots12 3.4 Approval testing.12 3.4.1 Safety tests only approval 12 3.4.2 Qualification approval 12 3.4.3 Sampling .13 3.4.4 Tests .13 3.5 Qu

24、ality conformance inspection .14 3.5.1 General .14 3.5.2 Formation of inspection lots .14 3.5.3 Test schedule 15 3.5.4 Delayed delivery 15 4 Test and measurement procedures .19 4.1 Earth inductors incorporated in filters.19 4.2 Capacitance and tan measurements19 4.3 Visual examination and check of d

25、imensions19 4.3.1 General .19 4.3.2 Creepage distances and clearances .19 EN 60939-2:2005 4 4.4 Voltage proof.20 4.4.1 Test circuit for d.c. tests.20 4.4.2 Applied voltage 20 4.4.3 Requirements 21 4.5 Insulation resistance21 4.5.1 Temperature correction 21 4.5.2 Requirements 21 4.6 DC line resistanc

26、e or voltage drop at rated current .21 4.6.1 DC line resistance21 4.6.2 Voltage drop at rated current22 4.7 Insertion loss.22 4.8 Discharge resistance .22 4.9 Robustness of terminations23 4.10 Resistance to soldering heat23 4.10.1 Test conditions 23 4.10.2 Intermediate inspection, measurements and r

27、equirements 23 4.11 Solderability 23 4.11.1 Test conditions 23 4.11.2 Requirements 23 4.12 Rapid change of temperature.23 4.12.1 Intermediate inspection 24 4.13 Vibration24 4.13.1 Test conditions 24 4.13.2 Intermediate inspection 24 4.14 Bump24 4.14.1 Test conditions 24 4.14.2 Intermediate inspectio

28、n, measurements and requirements 24 4.15 Shock.25 4.15.1 Test conditions 25 4.15.2 Intermediate inspection, measurements and requirements 25 4.16 Container sealing 25 4.16.1 Test conditions 25 4.16.2 Requirements 25 4.17 Climatic sequence .26 4.17.1 Initial measurements26 4.17.2 Dry heat26 4.17.3 Da

29、mp heat, cyclic, first cycle 26 4.17.4 Cold26 4.17.5 Low air pressure 26 4.17.6 Damp heat, cyclic, remaining cycles .26 4.17.7 Final inspection, measurements and requirements26 4.18 Damp heat, steady state 27 4.18.1 Test conditions 27 4.18.2 Final inspection, measurements and requirements27 4.19 Tem

30、perature rise .27 4.19.1 Test method.28 4.19.2 Requirements 29 4.20 Impulse voltage .29 4.20.1 Initial measurements29 5 EN 60939-2:2005 4.20.2 Test conditions 29 4.20.3 Requirements 30 4.21 Endurance.30 4.21.1 Test conditions current test .30 4.21.2 Test conditions voltage test, terminations/case 31

31、 4.21.3 Test conditions voltage test between terminations31 4.21.4 Test conditions combined voltage/current tests32 4.21.5 Final inspection, measurements and requirements32 4.22 Charge and discharge32 4.22.1 Initial measurements33 4.22.2 Test conditions 33 4.22.3 Final measurements and requirements

32、.33 4.23 Passive flammability 33 4.24 Current overload33 4.25 Solvent resistance of the marking 33 4.26 Component solvent resistance .34 4.27 Active flammability.34 Annex A (normative) Test schedule for qualification approval Assessment level D / DZ35 Annex B (normative) Test schedule for safety req

33、uirements only39 Annex C (normative) Circuit for the impulse voltage test .41 Annex D (normative) Circuit for the endurance test.43 Annex E (normative) Declaration of design .44 Annex ZA (normative) Normative references to international publications with their corresponding European publications45 F

34、igure 1 Impulse wave form .30 Figure C.1 Impulse voltage test circuit41 Table 1 Classification of class X capacitors 9 Table 2 Classification of class Y capacitors 10 Table 3 Tests concerning safety requirements only.15 Table 4 Sampling plan Safety and performance tests qualification approval Assess

35、ment level D / DZ.16 Table 5 Lot-by-lot-tests Assessment level D / DZ .17 Table 6 Lot-by-lot test Safety tests only approval.17 Table 7 Periodic tests Assessment level D / DZ .18 Table 8 Creepage distances and clearances.19 Table 9 Voltage proof.20 Table 10 Insulation resistance21 Table 11 Preferred

36、 severities .25 Table 12 Measurements and requirements after charge and discharge32 Table A.1 Test schedule for qualification approval Assessment level D / DZ .35 Table B.1 Test schedule for safety requirements only .39 Table C.1 Values of CX, CT, RP, RS, CP.41 Table C.2 Values and tolerances of Cx,

37、 tr, td.42 blank 7 EN 60939-2:2005 PASSIVE FILTER UNITS FOR ELECTROMAGNETIC INTERFERENCE SUPPRESSION Part 2: Sectional specification Passive filter units for which safety tests are appropriate Test methods and general requirements 1 General 1.1 Scope This Sectional specification applies to passive f

38、ilter units for electromagnetic interference suppression which fall within the scope of the Generic Specification IEC 60939-1. The scope of this Sectional specification is restricted to passive filter units for which safety tests are appropriate. This implies that filters specified according to this

39、 Sectional specification will either be connected to mains supplies, when compliance with the mandatory tests of Table 3 is necessary, or used in other circuit positions where the equipment specification prescribes that some or all of these safety tests are required. This Sectional specification app

40、lies to passive filter units which will be connected to an a.c. mains or other supply with a nominal voltage not exceeding 1 000 V a.c., with a nominal frequency not exceeding 400 Hz, or 1 000 V d.c. 1.2 Normative references The following referenced documents are indispensable for the application of

41、 this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE Components other than inductors and capacitors in the filter unit should fulfil requirements in the relevant IEC Standa

42、rd. IEC 60060-1, High-voltage test techniques Part 1: General definitions and test requirements IEC 60062, Marking codes for resistors and capacitors IEC 60068-1, Environmental testing Part 1: General and guidance IEC 60068-2-17, Basic environmental testing procedures Part 2: Tests Test Q: Sealing I

43、EC 60085, Thermal evaluation and classification of electrical insulation IEC 60335-1, Safety of household and similar electrical appliances Part 1: General requirements IEC 60384-9, Fixed capacitors for use in electronic equipment Part 9: Sectional specification: Fixed capacitors of ceramic dielectr

44、ic, Class 2 IEC 60384-14, Fixed capacitors for use in electronic equipment Part 14: Sectional specification: Fixed capacitors for electromagnetic interference suppression and connection to the supply mains EN 60939-2:2005 8 IEC 60664 (all parts), Insulation coordination for equipment within low-volt

45、age systems IEC 60938-1, Fixed inductors for electromagnetic interference suppression Part 1: Generic specification IEC 60939-1, Passive filter units for electromagnetic interference suppression Part 1: Generic specification IEC 60940, Guidance information on the application of capacitors, resistors

46、, inductors and complete filter units for radio interference suppression IEC 61140, Protection against electric shock Common aspects for installation and equipment 1.3 Information to be given in a detail specification 1.3.1 General The detail specifications shall be derived from the relevant blank d

47、etail specification. Detail specifications shall not specify requirements inferior to those of the generic, sectional or blank detail specification. When more severe requirements are included, they shall be listed in 1.9 of the detail specification, and indicated in the test schedules, for example b

48、y an asterisk. NOTE The information given in 1.3.2 may, for convenience, be presented in tabular form. The following information shall be given in each detail specification and the values quoted shall preferably be selected from the appropriate clause of this sectional specification. 1.3.2 Outline d

49、rawing and dimensions There shall be an illustration of the filter as an aid to easy recognition and for comparison of the filter with others. Dimensions and their associated tolerances, which affect inter-changeability and mounting, shall be given in the detail specification. All dimensions shall preferably be stated in millimetres. Normally, the numerical values shall be given for the l