BS EN 61068-1-1997 Polyester fibre woven tapes - Definitions designation and general requirements《聚酯纤维机织带 第1部分 定义、牌号和一般要求》.pdf

1、BRITISH STANDARD BS EN 61068-1:1997 IEC 61068-1: 1991 Specification for Polyester fibre woven tapes Part 1: Definitions, designation and general requirements The European Standard EN 61068-1:1997 has the status of a British Standard ICS 01.040.29; 29.035.20BSEN61068-1:1997 This British Standard, hav

2、ing been prepared under thedirectionof the Electrotechnical Sector Board,waspublished under theauthorityof the StandardsBoardand comes into effect on 15November1997 BSI 04-2000 ISBN 0 580 28495 6 National foreword This British Standard is the English language version of EN 61068-1:1997. It is identi

3、cal with IEC 61068-1:1991. It supersedes BS7809-1:1995which is withdrawn. The UK participation in its preparation was entrusted by Technical Committee GEL/15, Insulating materials, to Subcommittee GEL/15/3, Material specifications, which has the responsibility to: aid enquirers to understand the tex

4、t; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this subcommi

5、ttee can be obtained on request to its secretary. From1January 1997, all IEC publications have the number60000added to the old number. For instance, IEC27-1has been renumbered as IEC 60027-1. For a period of time during the change over from one numbering system to the other, publications may contain

6、 identifiers from both systems. Cross-references Attention is drawn to the fact that CEN and CENELEC Standards normally include an annex which lists normative references to international publications with their corresponding European publications. The British Standards which implement these internat

7、ional or European publications may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions

8、 of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, theEN title page, pag

9、es 2 to 4 and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Amendments issued since publication Amd. No. Date CommentsBSEN61068-1:1997 BSI 04-2000 i Contents Page Na

10、tional foreword Inside front cover Foreword 2 Text of EN 61068-1 3ii blankEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 61068-1 August 1997 ICS 29.035.20 Descriptors: Electrical insulating materials, solid electrical insulating materials, tapes, weaving, polyester fibres, definitions, designa

11、tion, dimensions, marking English version Specification for polyester fibre woven tapes Part 1: Definitions, designation and general requirements (IEC 61068-1:1991) Spcification pour rubans tisss en fibres de polyester Partie 1: Dfinitions, dsignation et prescriptions gnrales (CEI 61068-1:1991) Best

12、immung fr gewebte Bnder aus Polyesterfilamenten Teil 1: Definitionen, Bezeichnung und allgemeine Anforderungen (IEC 61068-1:1991) This European Standard was approved by CENELEC on 1997-07-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions

13、 for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three o

14、fficial versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical c

15、ommittees of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique

16、 Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B-1050 Brussels 1997 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 61068-1:1997 EEN61068-1:1997 BSI 04-2000 2 Foreword The text of the Inte

17、rnational Standard IEC 61068-1:1991, prepared by SC 15C, Specifications, of IEC TC 15, Insulating materials, was submitted to the formal vote and was approved by CENELEC as EN61068-1on 1997-07-01 without any modification. The following dates were fixed: Endorsement notice The text of the Internation

18、al Standard IEC61068-1:1991was approved by CENELEC as a European Standard without any modification. Contents Page Foreword 2 1 Scope 3 2 Definitions 3 3 Designation 3 4 General requirements 3 Figure 1 View of roll from locking thread side 4 Table 1 Thickness 4 Table 2 Nominal width 4 latest date by

19、which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 1998-06-01 latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 1998-06-01EN61068-1:1997 BSI 04-2000 3 1 Scope This part of IEC1068s

20、pecifies requirements for tapes woven on shuttleless looms for continuous filament polyester fibres. Nominal thicknesses of0,13mm to0,25mm and nominal widths of15mm, 20 mm and25mm are covered. The standard combinations of nominal thickness and nominal width are specified and an additional designatio

21、n is included for tapes which, whilst complying with the majority of the requirements of this part, are supplied with non-standard widths. This part gives definitions, a designation and general requirements. Other parts of IEC 1068 are: Part 2: Methods of test. Part 3: Specifications for individual

22、materials. 2 Definitions For the purpose of this part, the following definitions apply: 2.1 pick weft thread or group of threads inserted in a fabric by one traverse of the picking mechanism between two consecutive beat-ups 2.2 end individual warp thread 2.3 filament a single, very long fibre 2.4 lo

23、cking thread independent thread used to lock the weft threads 2.5 shuttleless loom loom in which the weft is inserted by means other than a shuttle and is drawn from a stationary supply 2.6 plain weave simplest of all weave interlacing in which the odd warp threads pass over one and under one weft p

24、ick throughout the fabric with the even warp thread reversing this order to under one, over one 2.7 heat set yarn yarn which has been heat treated so that subsequent shrinkage is reduced 2.8 central value middle value of an odd number of test measurements or the means of the two middle values of an

25、even number of test measurements when these measurements are arranged in order of magnitude NOTEThe central value is also known as the median. 3 Designation Tapes shall be designated in two types as defined below: Type 1 Tapes woven from polyester yarn so as to produce a tape with high shrinkage. Ty

26、pe 2 Tapes woven with heat set polyester yarn so as to produce a tape with low shrinkage. 4 General requirements 4.1 Construction The yarns used shall be continuous filament polyethylene terephthalate (PETP) and for type2shall be heat set. The tapes shall be plain weave. The picks shall be interlock

27、ed at or near the selvedge opposite the one from which the weft is inserted thus preventing unravelling of the selvedge during use. If a locking thread is used, the method of interlacing shall be such that the thread cannot be pulled out of the body of the tape. Tapes shall be identified according t

28、o type as follows: Type 1 A single black warp thread-positioned so as to indicate the centre line of the tape. Type 2 A single black warp thread positioned so as to indicate the centre line of the tape with two orange threads well offset one on each side of the black thread. 4.2 Thickness The nomina

29、l thickness measured between the selvedges of a tape shall be one of the values as given in Table 1, and the thickness as determined by the method given in 2.3 of IEC1068-2shall not fall outside the limits given in Table 1. The thickness, when measured at the selvedges, shall not exceed the thicknes

30、s between the selvedges by more than0,03mm.EN61068-1:1997 4 BSI 04-2000 Table 1 Thickness 4.3 Width The nominal widths of tapes complying fully with the requirements of this part are given in Table 2. Table 2 Nominal width The width as determined in accordance with the method given in 3.4 of Part2sh

31、all not differ from that specified by more than 1,0mm. 4.4 Requirements for rolls The tapes shall be wound on a hard tubular core with sufficient tension to form a compact roll but without deforming the structure of the tape. The internal diameter of the core shall be not less than10mm and not more

32、than13mm and its width shall be approximately the same as the width of the tape but shall not exceed it. An alternative internal core having a diameter of55mm is also permitted. NOTEThe length of tape in a roll is not a requirement of this part but it is normally50m. For types1and2the tapes shall be

33、 wound in an anti-clockwise spiral when the roll is viewed from the locking thread as shown in Figure 1. The number of joins per roll shall not exceed two and none of the lengths in a roll shall be shorter than10m. In any consignment, not more than10% of rolls shall have any join. Where a join occur

34、s, the tape ends shall be butted and joined up by a strip of coloured gummed tape which shall show on the edge of the roll to indicate the presence of a join. Pins or other metal fasteners shall not be used for securing the ends of rolls or for joining the tape. 4.5 Marking In addition to the identi

35、fication of the type of tape as specified in 4.1 the following information shall legibly be marked on individually packed rolls or on packages or on both: a) number of this part of the standard; b) designation of the type as specified in clause 3; c) nominal thickness of the tape in 1/100ths of a mi

36、llimetre; d) width of the tape in millimetres; e) length of the roll in metres; f) in the case of a package, the number of rolls. Nominal Minimum Maximum mm mm mm 0,13 0,20 0,25 0,12 0,17 0,22 0,17 0,22 0,27 Type Nominal thickness Nominal width mm mm 1 2 2 2 0,13 0,13 0,20 0,25 15 25 15 20 25 15 20

37、25 15 25 Figure 1 View of roll from locking thread sideblankBS EN 61068-1:1997 IEC 61068-1: 1991 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and

38、 at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and

39、services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an indivi

40、dual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to or

41、ders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Libra

42、ry and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developm

43、ents and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications o

44、f the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission fr

45、om BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.