BS EN 61076-4-107-2001 Connectors for electronic equipment - Printed board connectors with assessed quality - Detail specification for shielded two-part connectors having a basic gn.pdf

1、BRITISH STANDARD BS EN 61076-4-107: 2001 IEC 61076-4-107: 2001 Connectors for electronic equipment Part 4-107: Printed board connectors with assessed quality Detail specification for shielded two-part connectors having a basic grid of 2,0 mm, fixed part with solder and press-in terminations for prin

2、ted boards, free part with non-accessible insulation displacement and crimp terminations The European Standard EN 61076-4-107:2001 has the status of a British Standard ICS 31.220.10; 31.180 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBS EN 61076-4-107:2001 This British Stan

3、dard, having been prepared under the direction of the Electrotechnical Sector Policy and Strategy Committee, was published under the authority of the Standards Policy and Strategy Committee on 26 November 2001 BSI 26 November 2001 ISBN 0 580 38715 1 National foreword This British Standard is the off

4、icial English language version of EN 61076-4-107:2001. It is identical with IEC 61076-4-107:2001. The UK participation in its preparation was entrusted by Technical Committee EPL/48, Connectors for electronic equipment, to Subcommittee EPL/48/2, Electromechanical components for electronic equipment,

5、 which has the responsibility to: A list of organizations represented on this subcommittee can be obtained on request to its secretary. From 1 January 1997, all IEC publications have the number 60000 added to the old number. For instance, IEC 27-1 has been renumbered as IEC 60027-1. For a period of

6、time during the change over from one numbering system to the other, publications may contain identifiers from both systems. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the

7、 section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct applica

8、tion. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related in

9、ternational and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 45 and a back cover. The BSI copyright date displayed in this document indicates when the document was last issued. Amendm

10、ents issued since publication Amd. No. Date CommentsEUROPEAN STANDARD EN 61076-4-107 NORME EUROPENNE EUROPISCHE NORM October 2001 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central S

11、ecretariat: rue de Stassart 35, B - 1050 Brussels 2001 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 61076-4-107:2001 E ICS 31.220.10 English version Connectors for electronic equipment Part 4-107: Printed board connectors with

12、assessed quality - Detail specification for shielded two-part connectors having a basic grid of 2,0 mm, fixed part with solder and press-in terminations for printed boards, free part with non-accessible insulation displacement and crimp terminations (IEC 61076-4-107:2001) Connecteurs pour quipements

13、 lectroniques Partie 4-107: Connecteurs pour cartes imprimes sous assurance de la qualit Spcification particulire pour les connecteurs blinds en deux parties, au pas de base de 2,0 mm, partie fixe avec sorties soudes et CIF pour cartes imprimes, partie mobile avec sorties autodnudantes et serties (C

14、EI 61076-4-107:2001) Steckverbinder fr elektronische Einrichtungen Teil 4-107: Steckverbinder fr gedruckte Schaltungen mit bewerteter Qualitt - Bauartspezifikation fr geschirmte indirekte Steckverbinder im Raster 2,0 mm, freie Teile mit Lt- und Einpressanschlssen fr Leiterplatten, feste Teile mit ni

15、chtzugnglichen Schneidklemm- und Crimpanschlssen (IEC 61076-4-107:2001) This European Standard was approved by CENELEC on 2001-10-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a nationa

16、l standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in a

17、ny other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Czech Republic, Denmark, Fi

18、nland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.EN 61076-4-107:2001 - 2 - Foreword The text of document 48B/1066/FDIS, future edition 1 of IEC 61076-4-107, prepared by SC 48B, Connectors, of IEC

19、TC 48, Electromechanical components and mechanical structures for electronic equipment, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 61076-4-107 on 2001-10-01. The following dates were fixed: latest date by which the EN has to be implemented at national level by p

20、ublication of an identical national standard or by endorsement (dop) 2002-07-01 latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 2004-10-01 Annexes designated “normative“ are part of the body of the standard. Annexes designated “informative“ are given fo

21、r information only. In this standard, annexes A and ZA are normative. Annex ZA has been added by CENELEC. _ Endorsement notice The text of the International Standard IEC 61076-4-107:2001 was approved by CENELEC as a European Standard without any modification. _ Page2 EN610764107:2001 BSI26November20

22、0161076-4-107 IEC:2001 3 CONTENTS 1 General data 7 1.1 Recommended method of mounting 7 1.2 Ratings and characteristics. 7 1.3 Normative references . 8 1.4 Marking 9 1.5 IEC type designation10 1.6 Ordering information10 2 Technical information11 2.1 Definitions .11 2.2 Survey of styles and variants.

23、11 2.3 Information on application11 2.3.1 Complete connectors (pairs) 11 2.3.2 Fixed board connectors11 2.3.3 Free board connectors.11 2.3.4 Accessories .12 2.3.5 Shielding/grounding .12 2.3.6 Basic types of terminations 12 3 Dimensional information .12 3.1 General .12 3.2 Isometric view and common

24、features .13 3.3 Engagement (mating) information 13 3.4 Fixed board connectors .14 3.4.1 Dimensions14 3.4.2 Terminations15 3.5 Free board connectors.16 3.5.1 Dimensions16 3.5.2 Terminations17 3.6 Accessories.17 3.7 Mounting information for fixed board connectors18 3.7.1 Hole pattern on printed board

25、 18 3.7.2 Mounting on panels19 3.8 Mounting information for free board connectors (cable to cable, cable to panel, cable to printed board) 21 3.8.1 Connector with standard contacts 21 3.8.2 Connector with coaxial contacts.21 3.9 Gauges22 3.9.1 Sizing gauges and retention force gauges22 3.9.2 Mechani

26、cal operation, engaging/separating force, insertion/withdrawal force gauges 22 3.9.3 Probes.22 3.9.4 Contact resistance gauge 22 3.9.5 Test panels (for voltage proof test) 22 4 Characteristics23 4.1 Climatic category.23 4.2 Electrical .23 4.2.1 Creepage and clearance distances 23 Page3 EN610764107:2

27、001 BSI26November200161076-4-107 IEC:2001 4 4.2.2 Voltage proof .23 4.2.3 Current-carrying capacity.24 4.2.4 Contact resistance.24 4.2.5 Insulation resistance25 4.3 Mechanical 25 4.3.1 Mechanical operation.25 4.3.2 Insertion and withdrawal forces (or engaging and separating forces) .25 4.3.3 Contact

28、 retention in insert26 4.3.4 Polarizing method26 4.3.5 Cable clamp resistance to cable rotation27 4.3.6 Cable clamp resistance to cable pull (tensile) 27 4.3.7 Effectiveness of connector coupling devices 27 4.3.8 Static load, transverse .27 4.3.9 Vibration 28 4.3.10 Shock 28 5 Test schedule .28 5.1

29、General .28 5.1.1 Arrangement for contact resistance measurements29 5.1.2 Arrangement for measurement of voltage proof, insulation resistance and polarization voltage during damp heat test, steady state .29 5.1.3 Arrangement for dynamic stress tests 30 5.1.4 Arrangement for flammability test.30 5.2

30、Test schedule tables31 5.2.1 Basic test schedule31 5.2.2 Full test schedule.32 6 Quality assessment procedures 39 6.1 Qualification approval testing.39 6.1.1 Method 1 .39 6.1.2 Method 2 .39 6.2 Quality conformance inspection .40 6.2.1 Lot-by-lot tests.40 6.2.2 Periodic tests.41 6.3 Delayed delivery,

31、 re-inspection42 Annex A (normative) Survey of coaxial contacts43 Annex ZA (normative) Normative references to international publications with their corresponding European publications .44 Figure 1 Grid layout for 2 mm connector module . 7 Figure 2 Isometric view 13 Figure 3 Electrical engagement le

32、ngth .13 Figure 4 Fixed board connector with standard contacts 14 Figure 5 Fixed board connector with coaxial contacts.15 Figure 6 Terminations 15 Page4 EN610764107:2001 BSI26November200161076-4-107 IEC:2001 5 Figure 7 Free connector with standard contacts .16 Figure 8 Free connector with coaxial co

33、ntacts17 Figure 9 Hole pattern on printed board for fixed board connector with standard contacts 18 Figure 10 Hole pattern on printed board for fixed board connector with coaxial contacts .18 Figure 11 Fixed board connector with standard contacts (style A) panel mounted, packaging information .19 Fi

34、gure 12 Fixed board connector with coaxial contacts (style B) panel mounted, packaging information .20 Figure 13 Free connector with standard contacts (style D) .21 Figure 14 Free connector with coaxial contacts (style E) 21 Figure 15 Sizing and retention force gauge for female contacts22 Figure 16

35、Current-carrying capacity: derating curve .24 Figure 17 Points of connection for contact resistance measurement.24 Figure 18 Arrangement for testing of static load, transverse.28 Figure 19 Wiring of specimen.29 Figure 20 Arrangement for dynamic stress tests.30 Figure 21 Arrangement for flammability

36、test .30 Table 1 Styles and variants 11 Table 2 Basic types of terminations12 Table 3 Dimensions of terminations15 Table 4 Dimensions for sizing and retention force gauge for female contacts .22 Table 5 Performance level23 Table 6 Creepage and clearance distances23 Table 7 Voltage proof.23 Table 8 I

37、nsulation resistance25 Table 9 Number of mechanical operations25 Table 10 Insertion and withdrawal forces25 Table 11 Contact retention in insert26 Table 12 Insert retention in housing .26 Table 13 Vibration28 Table 14 Shock 28 Table 15 Number of specimens for inspection and test sequence.29 Table 16

38、 Basic (minimum) test schedule 31 Table 17 Test group P32 Table 18 Test group AP33 Table 19 Test group BP35 Table 20 Test group DP .36 Table 21 Test group EP37 Table 22 Test group GP .37 Table 23 Test group JP 38 Table 24 Qualification approval group information39 Table 25 Lot-by-lot tests.40 Table

39、26 Periodic tests.41 Table 27 Delayed delivery, re-inspection42 Table A.1 Survey of coaxial contacts43 Page5 EN610764107:2001 BSI26November200161076-4-107 IEC:2001 6 CONNECTORS FOR ELECTRONIC EQUIPMENT Part 4-107: Printed board connectors with assessed quality Detail specification for shielded two-p

40、art connectors having a basic grid of 2,0 mm, fixed part with solder and press-in terminations for printed boards, free part with non-accessible insulation displacement and crimp terminations IEC SC 48B: CONNECTORS IEC 61076-4-107 Specification available from: IEC Central Office or from the addresse

41、s shown on the inside cover QC 480301XX0008 Electronic components of assessed quality DETAIL SPECIFICATION in accordance with IEC 61076-1:1995 Blank detail specification: IEC 61076-4-001:1996 Rectangular printed board connector for solder and press-in terminations; cable-to-board connector for insul

42、ation displacement and crimp terminations Two coaxial or 10 standard contacts Terminations: solder, press-in, insulation displacement, crimp Performance levels (PL): 1 Assessment levels: B and G* Combinations of performance and assessment levels: Climatic categories: see 4.1 Electrical characteristi

43、cs: see 4.2 Mechanical characteristics: see 4.3 Ordering information: see 1.6 * See 6.2. IEC 1290/01 Page6 EN610764107:2001 BSI26November200161076-4-107 IEC:2001 7 1 General data 1.1 Recommended method of mounting A connector pair consists of one fixed board connector and one free connector module.

44、Both modules are completely shielded in order to fulfil future EMC requirements. Fixed board connector modules are mounted on the edge of the printed board and have female contacts with solder or press-in terminations. Free connector modules are mounted on cables and have male contacts with insulati

45、on displacement terminations for standard contacts and crimp terminations for coaxial contacts. 1.2 Ratings and characteristics Rated voltage: contact/contact 50 V Current rating: 1,5 A at 70 C (all contacts) Insulation resistance: 10 4M Climatic category: 25/125/04 Printed board hole diameter: for

46、connector with standard contacts: plated-through hole 0,6 mm min. for connector with coaxial contacts: plated-through hole 1,0 mm according to IEC 60352-5 Grid layout: contact spacing: 2 mm row z of the front panel is in line with the datum lane of the printed board termination row a on the printed

47、board lies 4 mm from the edge and 6,5 mm from the front panel a z bcde z a b c d e Datum plane Figure 1 Grid layout for 2 mm connector module IEC 1291/01 Page7 EN610764107:2001 BSI26November200161076-4-107 IEC:2001 8 1.3 Normative references The following normative documents contain provisions which

48、, through reference in this text, constitute provisions of this part of IEC 61076. For dated references, subsequent amendments to, or revisions of, any of these publications do not apply. However, parties to agreements based on this part of IEC 61076 are encouraged to investigate the possibility of

49、applying the most recent editions of the normative documents indicated below. For undated references, the latest edition of the normative document referred to applies. Members of IEC and ISO maintain registers of currently valid International Standards. IEC 60068-1:1988, Environmental testing Part 1: General and