1、BSI Standards PublicationIndustrial communication networks Fieldbus specificationsPart 5-23: Application layer service definition Type 23 elementsBS EN 61158-5-23:2014National forewordThis British Standard is the UK implementation of EN 61158-5-23:2014. It isidentical to IEC 61158-5-23:2014. The UK
2、participation in its preparation was entrusted to TechnicalCommittee AMT/7, Industrial communications: process measurement andcontrol, including fieldbus.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all
3、the necessary provisions ofa contract. Users are responsible for its correct application. The British Standards Institution 2014.Published by BSI Standards Limited 2014ISBN 978 0 580 79464 3ICS 25.040.40; 35.100.70; 35.110Compliance with a British Standard cannot confer immunity fromlegal obligation
4、s.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 31 October 2014.Amendments issued since publicationDate Text affectedBRITISH STANDARDBS EN 61158-5-23:2014EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 61158-5-23 October 2014 ICS 25.040
5、.40; 35.100.70; 35.110 English Version Industrial communication networks - Fieldbus specifications - Part 5-23: Application layer service definition - Type 23 elements (IEC 61158-5-23:2014) Rseaux de communication industriels - Spcifications des bus de terrain - Partie 5-23: Dfinition des services d
6、e la couche application - lments de type 23 (CEI 61158-5-23:2014) Industrielle Kommunikationsnetze - Feldbusse - Teil 5-23: Dienstfestlegungen des Application Layer (Anwendungsschicht) - Typ 23-Elemente (IEC 61158-5-23:2014) This European Standard was approved by CENELEC on 2014-09-22. CENELEC membe
7、rs are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on applicatio
8、n to the CEN-CENELEC Management Centre or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC
9、Management Centre has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland
10、, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisch
11、es Komitee fr Elektrotechnische Normung CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2014 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members. Ref. No. EN 61158-5-23:2014 E BS EN 61158-5-23:2014EN 61158-5-23:2014 - 2 - Foreword T
12、he text of document 65C/763/FDIS, future edition 1 of IEC 61158-5-23, prepared by SC 65C “Industrial networks” of IEC/TC 65 “Industrial-process measurement, control and automation“ was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN 61158-5-23:2014. The following dates are f
13、ixed: latest date by which the document has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2015-06-22 latest date by which the national standards conflicting with the document have to be withdrawn (dow) 2017-09-22 Attention is drawn to th
14、e possibility that some of the elements of this document may be the subject of patent rights. CENELEC and/or CEN shall not be held responsible for identifying any or all such patent rights. This document has been prepared under a mandate given to CENELEC by the European Commission and the European F
15、ree Trade Association. Endorsement notice The text of the International Standard IEC 61158-5-23:2014 was approved by CENELEC as a European Standard without any modification. In the official version, for Bibliography, the following notes have to be added for the standards indicated: IEC 61784-1 NOTE
16、Harmonized as EN 61784-1. IEC 61784-2 NOTE Harmonized as EN 61784-2. BS EN 61158-5-23:2014- 3 - EN 61158-5-23:2014 Annex ZA (normative) Normative references to international publications with their corresponding European publications The following documents, in whole or in part, are normatively refe
17、renced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE 1 When an International Publication has been modified by common modi
18、fications, indicated by (mod), the relevant EN/HD applies. NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here: www.cenelec.eu Publication Year Title EN/HD Year IEC 61158-1 2014 Industrial communication networks - Fieldbus specificati
19、ons - Part 1: Overview and guidance for the IEC 61158 and IEC 61784 series EN 61158-1 2014 IEC 61158-6 Series Industrial communication networks - Fieldbus specifications - Part 6: Application layer protocol specification EN 61158-6 Series ISO/IEC 646 - Information technology - ISO 7-bit coded charac
20、ter set for information interchange - - ISO/IEC 7498-1 - Information technology - Open Systems Interconnection - Basic reference model: The basic model - - ISO/IEC 8822 - Information technology - Open Systems Interconnection - Presentation service definition - - ISO/IEC 8824-1 - Information technolo
21、gy - Abstract Syntax Notation One (ASN.1): Specification of basic notation - - ISO/IEC 9545 - Information technology - Open Systems Interconnection - Application layer structure - - ISO/IEC 10731 - Information technology - Open Systems Interconnection - Basic Reference Model - Conventions for the de
22、finition of OSI services - - BS EN 61158-5-23:2014 2 IEC 61158-5-23:2014 IEC 2014 CONTENTS INTRODUCTION . 6 1 Scope . 7 General . 7 1.1Specifications 8 1.2Conformance . 8 1.32 Normative references . 8 3 Terms, definitions, symbols, abbreviated terms and conventions 9 Referenced terms and definitions
23、 9 3.1Type 23 specific terms and definitions . 10 3.2Symbols and abbreviated terms. 12 3.3Conventions 13 3.44 Concept 16 5 Data type ASE 16 Overview . 16 5.1Fixed length types . 16 5.26 Communication model specification 21 Communication model . 21 6.1ASE. 23 6.2AR type C 58 6.3AR type F 71 6.4Biblio
24、graphy 90 Figure 1 Cyclic model (n:n type distributed shared memory, unconfirmed push model) 22 Figure 2 Cyclic model (1:n type distributed shared memory, unconfirmed push model) 22 Figure 3 Transient model (Client server model) 22 Figure 4 Transient model (Push model) 23 Figure 5 Structure of ASE t
25、ype C of FAL type 23 . 23 Figure 6 Structure of ASE type F of FAL type 23 23 Figure 7 Structure of AR type C . 58 Figure 8 Structure of AR type F 71 Table 1 Ld service parameters . 25 Table 2 Set service parameters . 25 Table 3 Reset service parameters 25 Table 4 Read service parameters. 26 Table 5
26、Write service parameters . 26 Table 6 Ld service parameters . 27 Table 7 Set service parameters . 28 Table 8 Reset service parameters 28 Table 9 Read service parameters. 29 Table 10 Write service parameters . 29 Table 11 Ld service parameters . 31 Table 12 Set service parameters 32 BS EN 61158-5-23:
27、2014IEC 61158-5-23:2014 IEC 2014 3 Table 13 Reset service parameters 32 Table 14 Read service parameters . 32 Table 15 Write service parameters . 33 Table 16 Get memory access info service parameters . 36 Table 17 Run service parameters. 37 Table 18 Stop service parameters 37 Table 19 Read memory se
28、rvice parameters . 38 Table 20 Write memory service parameters . 39 Table 21 Get memory access info service parameters . 41 Table 22 Run service parameters. 42 Table 23 Stop service parameters 43 Table 24 Read memory service parameters . 44 Table 25 Write memory service parameters . 45 Table 26 Vend
29、or command service parameters 46 Table 27 Distribute node info service parameters . 47 Table 28 Get statistics service parameters . 48 Table 29 Get node info detail service parameters 49 Table 30 AC data service parameters 52 Table 31 AC data ND service parameters 53 Table 32 Get attribute service p
30、arameters . 54 Table 33 Set attribute service parameters 54 Table 34 Synchronization trigger service parameters . 56 Table 35 Start measurement service parameters . 57 Table 36 Get offset service parameters 58 Table 37 Control cyclic service parameters 62 Table 38 CT Update service parameters 64 Tab
31、le 39 AC Send service parameters . 65 Table 40 AC Param send service parameters 66 Table 41 CPD Set service parameters . 71 Table 42 Control cyclic service parameters 78 Table 43 CT Update service parameters 80 Table 44 AC Send service parameters . 81 Table 45 AC Send ND service parameters . 82 Tabl
32、e 46 Synchronous trigger internal service parameters . 86 Table 47 Measure send service parameters . 87 Table 48 MeasureAck send service parameters . 88 Table 49 Offset send service parameters . 88 Table 50 Update send service parameters . 89 BS EN 61158-5-23:2014 6 IEC 61158-5-23:2014 IEC 2014 INTR
33、ODUCTION This part of IEC 61158 is one of a series produced to facilitate the interconnection of automation system components. It is related to other standards in the set as defined by the “three-layer” fieldbus reference model described in IEC 61158-1. The application service is provided by the app
34、lication protocol making use of the services available from the data-link or other immediately lower layer. This standard defines the application service characteristics that fieldbus applications and/or system management may exploit. Throughout the set of fieldbus standards, the term “service” refe
35、rs to the abstract capability provided by one layer of the OSI Basic Reference Model to the layer immediately above. Thus, the application layer service defined in this standard is a conceptual architectural service, independent of administrative and implementation divisions. BS EN 61158-5-23:2014IE
36、C 61158-5-23:2014 IEC 2014 7 INDUSTRIAL COMMUNICATION NETWORKS FIELDBUS SPECIFICATIONS Part 5-23: Application layer service definition Type 23 elements 1 Scope General 1.1The fieldbus Application Layer (FAL) provides user programs with a means to access the fieldbus communication environment. In thi
37、s respect, the FAL can be viewed as a “window between corresponding application programs.” This standard provides common elements for basic time-critical and non-time-critical messaging communications between application programs in an automation environment and material specific to Type 12 fieldbus
38、. The term “time-critical” is used to represent the presence of a time-window, within which one or more specified actions are required to be completed with some defined level of certainty. Failure to complete specified actions within the time window risks failure of the applications requesting the a
39、ctions, with attendant risk to equipment, plant and possibly human life. This standard defines in an abstract way the externally visible service provided by the different Types of the fieldbus Application Layer in terms of a) an abstract model for defining application resources (objects) capable of
40、being manipulated by users via the use of the FAL service, b) the primitive actions and events of the service; c) the parameters associated with each primitive action and event, and the form which they take; and d) the interrelationship between these actions and events, and their valid sequences. Th
41、e purpose of this standard is to define the services provided to a) the FAL user at the boundary between the user and the Application Layer of the Fieldbus Reference Model, and b) Systems Management at the boundary between the Application Layer and Systems Management of the Fieldbus Reference Model.
42、 This standard specifies the structure and services of the IEC fieldbus Application Layer, in conformance with the OSI Basic Reference Model (ISO/IEC 7498-1) and the OSI Application Layer Structure (ISO/IEC 9545). FAL services and protocols are provided by FAL application-entities (AE) contained wit
43、hin the application processes. The FAL AE is composed of a set of object-oriented Application Service Elements (ASEs) and a Layer Management Entity (LME) that manages the AE. The ASEs provide communication services that operate on a set of related application process object (APO) classes. One of the
44、 FAL ASEs is a management ASE that provides a common set of services for the management of the instances of FAL classes. Although these services specify, from the perspective of applications, how request and responses are issued and delivered, they do not include a specification of what the requesti
45、ng and responding applications are to do with them. That is, the behavioral aspects of the applications are not specified; only a definition of what requests and responses they can BS EN 61158-5-23:2014 8 IEC 61158-5-23:2014 IEC 2014 send/receive is specified. This permits greater flexibility to the
46、 FAL users in standardizing such object behavior. In addition to these services, some supporting services are also defined in this standard to provide access to the FAL to control certain aspects of its operation. Specifications 1.2The principal objective of this standard is to specify the character
47、istics of conceptual application layer services suitable for time-critical communications, and thus supplement the OSI Basic Reference Model in guiding the development of application layer protocols for time-critical communications. A secondary objective is to provide migration paths from previously
48、-existing industrial communications protocols. It is this latter objective which gives rise to the diversity of services standardized as the various Types of IEC 61158, and the corresponding protocols standardized in subparts of IEC 61158-6. This specification may be used as the basis for formal App
49、lication Programming-Interfaces. Nevertheless, it is not a formal programming interface, and any such interface will need to address implementation issues not covered by this specification, including a) the sizes and octet ordering of various multi-octet service parameters, and b) the correlation of paired request and confirm, or indication and response, primitives. Conformance 1.3This standard does
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1