BS EN 61169-39-2011 Radio-frequency connectors Sectional specification for CQM series quick lock RF connectors《射频连接器 CQM系列快速锁定射频连接器分规范》.pdf

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationRadio-frequency connectorsPart 39: Sectional specification for CQM series quick lock RF connectorsBS EN 61169-39:2011National forewordThis British Standard is the UK implementati

2、on of EN 61169-39:2011. It is identical to IEC 61169-39:2009. It supersedes DD IEC/PAS 61169-39:2008, which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee EPL/46, Cables, wires and waveguides, radio frequency connectors and accessories for communication and

3、 signalling.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. BSI 2011ISBN 978 0 580 61964 9 ICS 33.120.30Compli

4、ance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 July 2011.Amendments issued since publicationAmd. No. Date Text affectedBRITISH STANDARDBS EN 61169-39:2011EUROPEAN

5、STANDARD EN 61169-39 NORME EUROPENNE EUROPISCHE NORM May 2011 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Management Centre: Avenue Marnix 17, B - 1000 Brussels 2011 CENELEC - All rig

6、hts of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 61169-39:2011 E ICS 33.120.30 English version Radio-frequency connectors - Part 39: Sectional specification for CQM series quick lock RF connectors (IEC 61169-39:2009) Connecteurs pour frquences radi

7、olectriques Partie 39: Spcification intermdiaire pour les connecteurs RF verrouillage rapide de la srie CQM (CEI 61169-39:2009) Hochfrequenz-Steckverbinder -Teil 39: Rahmenspezifikation fr HF-Steckverbinder der CQM-Serie mit Schnellverriegelung (IEC 61169-39:2009) This European Standard was approved

8、 by CENELEC on 2011-01-02. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national

9、 standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language an

10、d notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, L

11、atvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. BS EN 61169-39:2011EN 61169-39:2011 Foreword The text of document 46F/107/CDV, future edition 1 of IEC 61169-39, prepared by SC 46F, R.F. an

12、d microwave passive components, of IEC TC 46, Cables, wires, waveguides, R.F. connectors, R.F. and microwave passive components and accessories, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 61169-39 on 2011-01-02. Attention is drawn to the possibility that some of

13、 the elements of this document may be the subject of patent rights. CEN and CENELEC shall not be held responsible for identifying any or all such patent rights. The following dates were fixed: latest date by which the EN has to be implemented at national level by publication of an identical national

14、 standard or by endorsement (dop) 2011-10-02 latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 2014-01-02 Annex ZA has been added by CENELEC. _ Endorsement notice The text of the International Standard IEC 61169-39:2009 was approved by CENELEC as a Europe

15、an Standard without any modification. In the official version, for Bibliography, the following note has to be added for the standard indicated: IEC 62037 NOTE Harmonized as EN 62037. _ BS EN 61169-39:2011EN 61169-39:2011 Annex ZA (normative) Normative references to international publications with th

16、eir corresponding European publications The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE When

17、 an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. Publication Year Title EN/HDYearIEC 61169-1 1992 Radio-frequency connectors Part 1: Generic specification - General requirements and measuring methods EN 61169-1 1994 BS EN 61169-

18、39:201161169-39 IEC:2009(E) CONTENTS 1 Scope. . 1H6 2 Normative references . 2H6 3 Mating interface and gauge information . 3H6 3.1 Dimensions-General connectors Grade 2 4H7 3.1.1 Connector with pin-centre contact. 5H7 3.1.2 Connectors with socket-centre contact . . 6H8 3.2 Gauges . 7H9 3.2.1 Connec

19、tors with socket-centre contact . . 8H9 3.3 Dimensions standard test connectors Grade 0. . 9H11 3.3.1 Connector with pin-centre contact. 10H11 3.3.2 Connector with socket-centre contact . . 11H13 4 Quality assessment procedure. . 12H14 4.1 General . . 13H14 4.2 Rating and characteristics (see Clause

20、 6 of IEC 61169-1) . 14H14 4.3 Test schedule and inspection requirements 15H17 4.3.1 Acceptance tests . 16H17 4.3.2 Periodic tests . 17H18 4.4 Procedures. 18H19 4.4.1 Quality conformance inspection . . 19H19 4.4.2 Qualification approval and its maintenance. 20H19 5 Instructions for preparation of de

21、tail specifications . 21H19 5.1 General . . 22H19 5.2 Identification of the detail specification 23H20 5.3 Identification of the component. 24H20 5.4 Performance. 25H20 5.5 Marking, ordering information and related matters . . 26H20 5.6 Selection of tests, test conditions and severities 27H20 5.7 Bl

22、ank detail specification pro-forma for type CQM connector . . 28H21 Bibliography. 29H26 Figure 1 Connector with pin-centre contact (for dimensions, see Table 1) .30H7 Figure 2 Connector with socket-centre contact (for dimensions, see Table 2) . . 31H8 Figure 3 Gauge for outer contact of socket conne

23、ctor (for dimensions, see Table 3) . 32H9 Figure 4 Gauge pin for socket contact (for dimensions, see Table 4) . 33H9 Figure 5 Connector of pin-centre contact (for dimensions, see Table 5). 34H11 Figure 6 Standard test connector with socket-centre contact (for dimensions, see Table 6) . 35H13 Table 1

24、 Dimensions of connector with pin-centre contact .36H7 Table 2 Dimensions of connector with socket-centre contact. 37H8 Table 3 Dimensions of gauge for outer contact of socket connector . 38H9 Table 4 Dimensions of gauge pin for socket contact 39H10 Table 5 Dimensions of connector with pin-centre co

25、ntact . 40H12 BS EN 61169-39:201161169-39 IEC:2009(E) Table 6 Dimensions of standard test connector with socket-centre contact . . 41H14 Table 7 Ratings and characteristics . 42H15 Table 8 Acceptance tests . 43H17 Table 9 Periodic tests . . 44H18 BS EN 61169-39:2011 6 61169-39 IEC:2009(E) RADIO-FREQ

26、UENCY CONNECTORS Part 39: Sectional specification for CQM series quick lock RF connectors 1 Scope CQM series quick lock connectors with characteristic impedance 50 are used for high power microwave applications, connecting with RF cables or microstrips. The operating frequency limit is at least 4 GH

27、z. This sectional specification provides information and rules for the preparation of detail specifications for CQM series quick lock RF connectors together with the pro forma blank detail specification (DS). It also prescribes mating interface dimensions for general purpose connectors, dimensional

28、details of standard test connectors grade 0, gauging information and tests selected from IEC 61169-1, applicable to all detail specifications relating to CQM series connectors. This specification indicates the recommended performance characteristics to be considered when writing a detail specificati

29、on and it covers test schedules and inspection requirements for assessment levels M and H. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest editio

30、n of the referenced document (including any amendments) applies. IEC 61169-1:1992, Radio-frequency connectors Part 1: Generic specification General requirements and measuring methods 3 Mating interface and gauge information All undimensioned pictorial configurations are for reference purposes only.

31、BS EN 61169-39:201161169-39 IEC:2009(E) 7 3.1 Dimensions-General connectors Grade 2 3.1.1 Connector with pin-centre contact Note 1Note 2 Note 4 R1,5 +0,10 Note 3pmnhib a sec dlf gkju v t IEC 993/09 Figure 1 Connector with pin-centre contact (for dimensions, see Table 1) Table 1 Dimensions of connect

32、or with pin-centre contact Reference mm Note min max a 5,96 6,04 Diameter b 7(nominal) Diameter c 15,85 16,25 Diameter d 16,90 17,10 Diameter e 18,00 18,20 Diameter f 21,00 21,20 Diameter g 21,90 22,10 Diameter h 8,90 9,20 i 3,70 3,90 j 4,30 4,50 k - 9,80 l 0,30 0,50 m 8,80 9,00 n 7,20 7,40 p 4,20 4

33、,40 s 23,20 23,30 Diameter t 35,00 35,20 Diameter u 2,10 2,30 v 26,9 27,2 Diameter NOTE 1 Mechanical reference plane. NOTE 2 The spring force is 50 N to 60 N max. NOTE 3 Tolerances of dimensions are to meet the requirements of characteristic impedances. NOTE 4 Ring. BS EN 61169-39:2011 8 61169-39 IE

34、C:2009(E) 3.1.2 Connectors with socket-centre contact Note 6 Note 5 Note 4Note 3Note 2Note 1gfuij hn em abc d q pl kr s1,5 45 IEC 994/09 Figure 2 Connector with socket-centre contact (for dimensions, see Table 2) Table 2 Dimensions of connector with socket-centre contact Reference mm Note min max a

35、7（ nominal） Diameter (Note 1) b 15,85 16,25 Diameter c 16,70 16,90 Diameter d 17,80 18,00 Diameter e 22,10 22,30 Diameter f 6,30 6,50 g 9,10 9,30 h 12,75 12,85 i 0,20 0,40 j - 0,20 k 7,00 7,50 l 8,50 9,00 m 23,60 23,80 Diameter n 35,20 35,40 Diameter p 0,80 1,00 q 1,10 1,30 r 1,60 - s 2,60 - u 4,90

36、5,20 NOTE 1 Design for slotting optional, closed contacts should meet electrical and mechanical requirements. NOTE 2 Design for slotting optional, flared contacts d should be flared to 18,4 18,5. NOTE 3 Mechanical reference plane. NOTE 4 Three steel balls, 3. NOTE 5 The spring force is 2 N to 6 N, m

37、ovement is 1,60 mm min. NOTE 6 Ring. BS EN 61169-39:201161169-39 IEC:2009(E) 9 3.2 Gauges 3.2.1 Connectors with socket-centre contact 3.2.1.1 Gauge for outer contact of socket connector v w s t u IEC 995/09Figure 3 Gauge for outer contact of socket connector (for dimensions, see Table 3) Table 3 Dim

38、ensions of gauge for outer contact of socket connector Gauge A (for sizing purposes) Gauge B (for measurement of gauge retention force for outer conductor) Mass (weight) of gauge: 200 g 5 g mm mm Ref. min max min max Note s 18,05 18,10 18,15 18,18 t 18,70 18,80 18,70 18,80 u 20,00 20,80 20,00 20,80

39、v 9,50 9,60 9,40 9,50 w 1,30 1,50 1,30 1,50 NOTE Material: steel, polished, surface roughness: Ra 0,4 m. 3.2.1.2 Test sequence Gauge A shall be placed over the outer contact of the connector once. This is a sizing operation. After this, gauge B shall be placed over the outer contact in a vertical po

40、sition. The gauge shall be retained. 3.2.1.3 Gauge pin for socket-centre contact a5,6 mm min.7,6 mm max.IEC 996/09 Figure 4 Gauge pin for socket contact (for dimensions, see Table 4) BS EN 61169-39:2011 10 61169-39 IEC:2009(E) Table 4 Dimensions of gauge pin for socket contact Gauge C (for sizing pu

41、rposes) Gauge D (for measurement of gauge retention force for centre contact) Mass (weight) of gauge: 600 g 5 g mm mm Ref. min max min max a 6,05 6,10 5,95 6,00 NOTE Material: steel, polished, surface roughness: Ra 0,4 m.3.2.1.4 Test sequence Test pin gauge C shall be inserted into the centre contac

42、t three times with a minimum depth of 5,6 mm. This is a sizing operation and should only be carried out when the socket centre contact is removed from the connector. After this, gauge D shall be inserted and held in the vertical position. The gauge shall be retained. This test can also be carried ou

43、t on connector when the socket centre contact is not removed once the sizing operation has been carried out on the contact whilst it was removed from the connector. BS EN 61169-39:201161169-39 IEC:2009(E) 11 3.3 Dimensions standard test connectors Grade 0 3.3.1 Connector with pin-centre contact y x

44、abj kg tfl n m dc e si h vNote 1 Note 3 R1,5 +0,10 Note 2 BA0,05 mm BR0,5u 0,05 mm A 8 10IEC 997/09 Figure 5 Connector of pin-centre contact (for dimensions, see Table 5) BS EN 61169-39:2011 12 61169-39 IEC:2009(E) Table 5 Dimensions of connector with pin-centre contact Reference mm Note min max a 5

45、,99 6,00 Diameter b 6,97 6,98 Diameter c 16,05 16,07 Diameter d 16,96 17,04 Diameter e 18,05 18,15 Diameter f 21,05 21,15 Diameter g 21,95 22,05 Diameter h 9,02 9,08 i 3,77 3,83 j 4,35 4,45 k 9,70 9,80 l 0,30 0,50 m 8,86 8,94 n 7,27 7,33 s 22,20 22,25 Diameter t 23,04 23,10 Diameter u 2,15 2,25 v 27

46、,00 27,10 Diameter x 4,20 4,40 y 7,20 7,40 NOTE 1 Mechanical reference plane. NOTE 2 The spring force is 50 N to 60 N. NOTE 3 Ring. BS EN 61169-39:201161169-39 IEC:2009(E) 13 3.3.2 Connector with socket-centre contact guh j i fd c bm e n r sp q w vR0,3 Note 5 Note 6 Note 3 Note 1 Note 2Note 41,5 45

47、0,05 mm A x y AIEC 998/09 Figure 6 Standard test connector with socket-centre contact (for dimensions, see Table 6) BS EN 61169-39:2011 14 61169-39 IEC:2009(E) Table 6 Dimensions of standard test connector with socket-centre contact Reference mm Note min max b 16,05 16,07 Diameter c 16,92 16,96 Diam

48、eter d 18,01 18,05 e 22,18 22,25 Diameter f 6,35 6,42 g 9,18 9,25 h 12,78 12,81 i 0,28 0,32 j - 0,20 m 23,68 23,75 Diameter n 35,25 35,35 Diameter p 0,88 0,96 q 1,06 1,14 r 1,60 - s 2,60 - u 4,95 5,05 v See Note 4 w 6,97 7,00 Diameter x 7,00 7,20 y 8,50 9,00 NOTE 1 Three steel balls, 3. NOTE 2 Desig

49、n for slotting optional, flared contacts d should be flared to 18,40 18,50. NOTE 3 Mechanical reference plane. NOTE 4 When a gauge pin with diameter of 5,99 mm min 6 mm max is inserted into a depth of 5,00 mm min, dimension v should meet the requirements of dimension w. NOTE 5 The spring force is 2 N to 6 N, movement is 1,60 mm min. NOTE 6 Ring. 4 Quality asses