BS EN 61169-54-2016 Radio-frequency connectors Sectional specification for coaxial connectors with 10 mm inner diameter of outer conductor nominal characteristic impedance 50 $2I s.pdf

1、Radio-frequency connectorsPart 54: Sectional specification for coaxial connectors with 10 mm inner diameter of outer conductor, nominal characteristic impedance 50 , series 4,3-10BS EN 61169-54:2016BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06National forewordThis

2、 British Standard is the UK implementation of EN 61169-54:2016. It isidentical to IEC 61169-54:2016. The UK participation in its preparation was entrusted to TechnicalCommittee EPL/46, Cables, wires and waveguides, radio frequency connectors and accessories for communication and signalling.A list of

3、 organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisions ofa contract. Users are responsible for its correct application. The British Standards Institution 2016.Published by BSI Standards Limited

4、 2016ISBN 978 0 580 87376 8ICS 33.120.30Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 31 December 2016.Amendments/corrigenda issued since publicationDate Text af

5、fectedBRITISH STANDARDBS EN 61169-54:2016EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 61169-54 December 2016 ICS 33.120.30 English Version Radio-frequency connectors - Part 54: Sectional specification for coaxial connectors with 10 mm inner diameter of outer conductor, nominal characteristic

6、 impedance 50 , series 4,3-10 (IEC 61169-54:2016) Connecteurs pour frquences radiolectriques - Partie 54: Spcification intermdiaire relative aux connecteurs coaxiaux avec diamtre intrieur du conducteur extrieur de 10 mm, impdance caractristique nominale de 50 , srie 4,3-10 (IEC 61169-54:2016) Hochfr

7、equenz-Steckverbinder - Teil 54: Rahmenspezifikation fr koaxiale Hochfrequenzsteckverbinder mit 10 mm Innendurchmesser des Auenleiters, Wellenwiderstand 50 , Typ 4,3-10 (IEC 61169-54:2016) This European Standard was approved by CENELEC on 2016-10-11. CENELEC members are bound to comply with the CEN/

8、CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Cent

9、re or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same statu

10、s as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,

11、 Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Norm

12、ung CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2016 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members. Ref. No. EN 61169-54:2016 E BS EN 61169-54:2016EN 61169-54:2016 2 European foreword The text of document 46F/348/FDIS, fut

13、ure edition 1 of IEC 61169-54, prepared by SC 46F “RF and microwave passive components“, of IEC/TC 46 “Cables, wires, waveguides, RF connectors, RF and microwave passive components and accessories“ was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN 61169-54:2016. The follow

14、ing dates are fixed: latest date by which the document has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2017-07-11 latest date by which the national standards conflicting with the document have to be withdrawn (dow) 2019-10-11 Attention

15、 is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC and/or CEN shall not be held responsible for identifying any or all such patent rights. Endorsement notice The text of the International Standard IEC 61169-54:2016 was approved by CEN

16、ELEC as a European Standard without any modification. BS EN 61169-54:2016EN 61169-54:2016 3 Annex ZA (normative) Normative references to international publications with their corresponding European publications The following documents, in whole or in part, are normatively referenced in this document

17、 and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE 1 When an International Publication has been modified by common modifications, indicated by

18、 (mod), the relevant EN/HD applies. NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here: www.cenelec.eu. Publication Year Title EN/HD Year IEC 61169-1 2013 Radio-frequency connectors - Part 1: Generic specification - General requireme

19、nts and measuring methods EN 61169-1 2013 IEC 62037-1 2012 Passive RF and microwave devices, intermodulation level measurement - Part 1: General requirements and measuring methods EN 62037-1 2012 BS EN 61169-54:2016 2 IEC 61169-54:2016 IEC 2016 CONTENTS FOREWORD . 4 INTRODUCTION . 6 1 Scope 7 2 Norm

20、ative references. 7 3 Mating face and gauge information . 7 3.1 Dimensions General connectors Grade 2 . 7 3.1.1 Connector with pin-centre contact (see Figure 1) 7 3.1.2 Connector with socket-centre contact (see Figure 2) . 10 3.1.3 Presentation of possible coupling mechanisms . 12 3.2 Gauges . 15 3.

21、2.1 Gauge pins for socket-centre contact (see Figure 6) . 15 3.2.2 Test procedure . 15 3.2.3 Gauge rings for plug outer contact (see Figure 7) . 16 3.2.4 Test procedure . 16 3.3 Dimensions Standard test connectors Grade 0 . 17 3.3.1 Connector with pin-centre contact (see Figure 8) 17 3.3.2 Connector

22、 with socket-centre contact (see Figure 9) . 19 4 Quality assessment procedure . 20 4.1 General . 20 4.2 Ratings and characteristics . 21 4.3 Test schedule and inspection requirements 24 4.3.1 Acceptance tests 24 4.3.2 Periodic tests . 25 4.4 Procedures for quality conformance . 26 4.4.1 Quality con

23、formance inspection 26 4.4.2 Quality conformance and its maintenance . 26 4.5 Test and measurement procedures 26 4.5.1 General . 26 4.5.2 Schedule of basic test groupings for acceptance and periodic tests . 26 4.6 Specifications . 27 4.6.1 Specification structures 27 4.6.2 Sectional specification (S

24、S) 27 4.6.3 Detail specification (DS) . 27 4.6.4 Blank detail specification 27 4.6.5 Blank detail specification pro-forma for 50 type 4,3-10 connectors . 28 5 Marking . 33 5.1 Marking of component . 33 5.2 Marking and contents of package 34 Figure 1 Connector with pin-centre contact (for dimensions

25、and key, see Table 1) . 8 Figure 2 Connector with socket-centre contact (for dimensions and key, see Table 2) . 10 Figure 3 Screw type . 12 Figure 4 Hand screw type. 13 Figure 5 Quick lock type . 14 Figure 6 Gauge pins for socket-centre contact (for dimensions, see Table 3). 15 BS EN 61169-54:2016IE

26、C 61169-54:2016 IEC 2016 3 Figure 7 Gauge rings for socket outer contact (for dimensions see Table 4) 16 Figure 8 Connector with pin-centre contact (for dimensions and key, see Table 5) . 17 Figure 9 Connector with socket-centre contact (for dimensions and key, see Table 6) . 19 Table 1 Dimensions o

27、f connector with pin-centre contact 9 Table 2 Dimensions of connector with socket-centre contact . 11 Table 3 Dimensions of gauge pins for socket-centre contact . 15 Table 4 Dimensions of gauge rings for socket outer contact 16 Table 5 Dimensions of connector with pin-centre contact 18 Table 6 Dimen

28、sions of connector with socket-centre contact . 20 Table 7 Climatic categories 21 Table 8 Ratings and characteristics 22 Table 9 Acceptance tests . 24 Table 10 Periodic tests 25 BS EN 61169-54:2016 4 IEC 61169-54:2016 IEC 2016 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ RADIO-FREQUENCY CONNECTORS Pa

29、rt 54: Sectional specification for coaxial connectors with 10 mm inner diameter of outer conductor, nominal characteristic impedance 50 , series 4,3-10 FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechn

30、ical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,

31、 Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, gov

32、ernmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions

33、 or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for internatio

34、nal use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order t

35、o promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly

36、 indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodi

37、es. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property

38、 damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this

39、 publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or

40、all such patent rights. International Standard IEC 61169-54 has been prepared by subcommittee 46F: RF and microwave passive components, of IEC technical committee 46: Cables, wires, waveguides, RF connectors, RF and microwave passive components and accessories. The text of this standard is based on

41、the following documents: FDIS Report on voting 46F/348/FDIS 46F/354/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. BS EN 61169

42、-54:2016IEC 61169-54:2016 IEC 2016 5 A list of all parts of the IEC 61169 series, under the general title: Radio-frequency connectors, can be found on the IEC website. The committee has decided that the contents of this publication will remain unchanged until the stability date indicated on the IEC

43、website under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. IMPORTANT The colour inside logo on the cover page of this publication indicates that it contains colours wh

44、ich are considered to be useful for the correct understanding of its contents. Users should therefore print this document using a colour printer. BS EN 61169-54:2016 6 IEC 61169-54:2016 IEC 2016 INTRODUCTION The International Electrotechnical Commission (IEC) draws attention to the fact that it is c

45、laimed that compliance with this document may involve the use of a patent concerning the design of these connectors given in 3.1.2. IEC takes no position concerning the evidence, validity and scope of this patent right. The holder of this patent right has assured the IEC that he/she is willing to ne

46、gotiate licences under reasonable and non-discriminatory terms and conditions with applicants throughout the world. In this respect, the statement of the holder of this patent right is registered with IEC. More detailed Information may be obtained from: Mrs. Julia Mayer Mrs. Katrin Groeger eMail: ju

47、lia.mayerkathrein.de eMail: katrin.groegerspinner- Phone: +49 8031 184 5084 Phone: +49 89 126010 1-3, Anton-Kathrein-St. 33, Erzgiessereistr. D-83022 Rosenheim D-80335 Muenchen Germany Germany Attention is drawn to the possibility that some of the elements of this document may be the subject of pate

48、nt rights other than those identified above. IEC shall not be held responsible for identifying any or all such patent rights. ISO (www.iso.org/patents) and IEC (http:/patents.iec.ch) maintain on-line data bases of patents relevant to their standards. Users are encouraged to consult the data bases fo

49、r the most up to date information concerning patents. BS EN 61169-54:2016IEC 61169-54:2016 IEC 2016 7 RADIO-FREQUENCY CONNECTORS Part 54: Sectional specification for coaxial connectors with 10 mm inner diameter of outer conductor, nominal characteristic impedance 50 , series 4,3-10 1 Scope This part of IEC 61169, which is a sectional specification (SS), provides information and rules for the preparation of detail specification