BS EN 61249-7-1-1996 Materials for interconnection structures - Sectional specification set for restraining core materials - Copper invar copper《互连接装置用材料 第7部分 芯约束用材料分规范 第1节 铜 殷钢 铜》.pdf

1、BRITISH STANDARD BS EN 61249-7-1:1996 IEC 1249-7-1: 1995 Materials for interconnection structures Part 7: Sectional specification set for restraining core materials Section 1: Copper/invar/copper The European Standard EN 61249-7-1:1995 has the status of a British Standard ICS 31.180BSEN61249-7-1:199

2、6 This British Standard, having been prepared under the direction of theElectrotechnical Sector Board, was published under the authority of the Standards Board and comesinto effect on 15 August 1996 BSI 11-1999 The following BSI references relate to the work on this standard: Committee reference EPL

3、/52 Draft announced in BSI News Update May 1996 ISBN 0 580 26031 3 Committees responsible for this British Standard The preparation of this British Standard was entrusted to Technical Committee EPL/52, Printed circuits, on which the following bodies were represented: British Telecommunications plc E

4、lectrical and Electronic Industries Association (BEAMA Ltd.) Federation of the Electronics Industries GAMBICA (BEAMA Ltd.) Institute of Metal Finishing National Supervisory Inspectorate Printed Circuit Interconnection Federation Surface Mount CIC type B Copper/Invar/copper in the ratio12,5/75/12,5 b

5、y volume percentage; CIC type C Copper/Invar/copper in the ratio20/60/20 by volume percentage. The tolerance shall be 10 % of the nominal content of each component. 3.2 Constituent materials 3.2.1 Invar Nickel-iron alloy of the following composition: 3.2.2 Copper The copper shall have a minimum puri

6、ty of 99,8 % copper (with silver content regarded as copper), excluding any “as shipped” surface treatment. Element % by weight Nickel 35,5 36,5 Phosphorus 0,025 maximum Sulphur 0,025 maximum Carbon 0,12 maximum Manganese 0,50 maximum Silicon 0,25 maximum Iron balanceEN61249-7-1:1995 4 BSI 11-1999 4

7、 Electrical properties Table 1 Electrical properties 5 Non-electrical properties 5.1 Appearance The copper-clad faces shall be free from oxide, blisters, wrinkles, pin-holes, deep scratches, and pits. 5.2 Thickness The thickness of the CIC material, measured by a micrometer, shall not depart from th

8、e nominal thickness by more than the appropriate value shown below. Table 2 Thickness tolerances 5.3 Bow and twist Table 3 Bow and twist 5.4 Tensile strength and elongation Table 4 Tensile and elongation properties Property Test method CIC type Requirement M7m Resistivity As specified in IEC 468 A 0

9、,17 0,01 B 0,07 0,01 C 0,04 0,01 Nominal thickness mm Tolerance mm 0,10 to 0,30 0,010 Over 0,30 to 0,60 0,025 Over 0,60 to 1,20 0,050 Over 1,20 to 2,40 0,10 Property Test method (sub-clause of IEC249-1) Requirement For all CIC types % Bow 3.1 0,5 max. Twist 3.3 0,5 max. Property Test method CIC type

10、 Requirement Tensile strength As specified in ISO 6892 A 380 N/mm 2to 480 N/mm 2 B 380 N/mm 2to 480 N/mm 2 C 310 N/mm 2to 480 N/mm 2 Elongation (gauge length: 50mm) As specified in ISO 6892 A 25 % min. B 20 % min. C 20 % min.EN61249-7-1:1995 BSI 11-1999 5 5.5 Modulus of elasticity Table 5 Modulus of

11、 elasticity 5.6 Thermal coefficient of expansion Table 6 Thermal coefficient of expansion 5.7 Bond strength between copper and Invar The CIC material shall be capable of being bent 180 around an arbor with a diameter equal to the thickness of the material without showing separation between the layer

12、s, at room temperature. 6 Surface treatment The sheet shall be capable of being bonded to a laminate according to the suppliers recommendations. If agreed upon between purchaser and supplier, the copper surface may be given a chemical or electrochemical treatment to enhance adhesion to the required

13、substrate. If such a treatment has been applied, it shall be substantially uniform in colour and intensity over the entire area of the surface so treated, and shall be sufficiently adherent to withstand normal handling of the material during the users manufacturing processes, including the laminatio

14、n process itself, and to meet the relevant requirements of the laminate manufactured from the CIC material. 7 Packaging and marking The material shall be packed adequately to avoid damage, bow, contamination in transit and storage. Separate sheets shall be interleaved with chemically neutral, or sui

15、tably treated paper. Each package shall be labelled with the material type designation, the manufacturers name, the nominal material thickness and the batch reference number. The package label shall also show the number of sheets. Any labels on sheets shall remain securely fixed during normal handli

16、ng but shall be capable of easy removal prior to fabrication. By agreement between purchaser and supplier, the order number may be substituted for material type designation and batch reference number, and total weight may be substituted for number of sheets. Property Test method CIC type Requirement

17、 N/mm 2 Modulus of elasticity As specified in ISO 178 A 147 10 3min. B 140 10 3min. C 135 10 3min. Property Test method (sub-clause of IEC 249-1) CIC type Requirement 10 6K 1 Machine direction Transversal direction Thermal coefficient of expansion (over the range 5 C to 125 C) 4.5 A 3,0 to 5,0 3,6 t

18、o 5,7 B 3,6 to 5,7 3,6 to 5,7 C 4,2 to 6,2 3,6 to 5,7EN61249-7-1:1995 6 BSI 11-1999 Annex ZA (normative) Normative references to international publications with their corresponding European publications This European Standard incorporates by dated or undated reference, provisions from other publicat

19、ions. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision.

20、For undated references the latest edition of the publication referred to applies (including amendments). NOTE. When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. Publication Year Title EN/HD Year IEC 249-1 1982 Base materials

21、for printed circuits EN 60249-1 a 1993 Part 1: Test methods IEC 468 1974 Method of measurement of resistivity of metallic materials ISO 6892 1984 Metallic materials Tensile testing ISO 178 1993 Plastics Determination of flexural properties a EN 60249-1 includes A1:1984 + A2:1989 + A3:1991 to IEC 249

22、-1.BSEN61249-7-1:1996 BSI 11-1999 List of references See national foreword.BS EN 61249-7-1:1996 IEC1249-7-1: 1995 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standa

23、rds in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of

24、our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers

25、members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001.

26、In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards

27、through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with s

28、tandards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of t

29、he publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior writ

30、ten permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.