BS EN 61300-2-37-2016 Fibre optic interconnecting devices and passive components Basic test and measurement procedures Tests Cable bending for fibre optic closures《纤维光学互连器件和无源元件 基本.pdf

1、Fibre optic interconnecting devices and passive components Basic test and measurement proceduresPart 2-37: Tests Cable bending for fibre optic closuresBS EN 61300-2-37:2016BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06National forewordThis British Standard is the U

2、K implementation of EN 61300-2-37:2016. It isidentical to IEC 61300-2-37:2016. It supersedes BS EN 61300-2-37:2007which is withdrawn.The UK participation in its preparation was entrusted by TechnicalCommittee GEL/86, Fibre optics, to Subcommittee GEL/86/2, Fibre opticinterconnecting devices and pass

3、ive components.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisions ofa contract. Users are responsible for its correct application. The British Standards Institution 2016.Published

4、by BSI Standards Limited 2016ISBN 978 0 580 82839 3ICS 33.180.20Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 31 August 2016.Amendments/corrigenda issued since p

5、ublicationDate Text affectedBRITISH STANDARDBS EN 61300-2-37:2016EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 61300-2-37 August 2016 ICS 33.180.20 Supersedes EN 61300-2-37:2007 English Version Fibre optic interconnecting devices and passive components - Basic test and measurement procedures

6、- Part 2-37: Tests - Cable bending for fibre optic closures (IEC 61300-2-37:2016) Dispositifs dinterconnexion et composants passifs fibroniques - Procdures fondamentales dessais et de mesures - Partie 2-37: Essais - Courbure du cble pour les botiers pour fibres optiques (IEC 61300-2-37:2016) Lichtwe

7、llenleiter - Verbindungselemente und passive Bauteile - Grundlegende Prf- und Messverfahren - Teil 2-37: Prfungen - Kabelbiegung bei Muffen (IEC 61300-2-37:2016) This European Standard was approved by CENELEC on 2016-05-25. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulation

8、s which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member

9、. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.

10、 CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Net

11、herlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung CEN-CENELEC Management

12、Centre: Avenue Marnix 17, B-1000 Brussels 2016 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members. Ref. No. EN 61300-2-37:2016 E BS EN 61300-2-37:2016EN 61300-2-37:2016 2 European foreword The text of document 86B/3975/FDIS, future edition 3 of IEC

13、 61300-2-37, prepared by SC 86B “Fibre optic interconnecting devices and passive components” of IEC/TC 86 “Fibre optics” was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN 61300-2-37:2016. The following dates are fixed: latest date by which the document has to be implemente

14、d at national level by publication of an identical national standard or by endorsement (dop) 2017-02-25 latest date by which the national standards conflicting with the document have to be withdrawn (dow) 2017-05-25 This document supersedes EN 61300-2-37:2007. Attention is drawn to the possibility t

15、hat some of the elements of this document may be the subject of patent rights. CENELEC and/or CEN shall not be held responsible for identifying any or all such patent rights. Endorsement notice The text of the International Standard IEC 61300-2-37:2016 was approved by CENELEC as a European Standard

16、without any modification. In the official version, for Bibliography, the following notes have to be added for the standards indicated: IEC 61300-2-23 NOTE Harmonized as EN 61300-2-23. IEC 61300-3-3 NOTE Harmonized as EN 61300-3-3. IEC 61753-1 NOTE Harmonized as EN 61753-1. BS EN 61300-2-37:2016EN 61

17、300-2-37:2016 3 Annex ZA (normative) Normative references to international publications with their corresponding European publications The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the e

18、dition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. NOTE 2 Up-to-date information on the lat

19、est versions of the European Standards listed in this annex is available here: www.cenelec.eu Publication Year Title EN/HD Year IEC 61300-1 - Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 1: General and guidance EN 61300-1 - IEC 61300-2-38

20、- Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-38: Tests - Sealing for pressurized fibre optic closures EN 61300-2-38 - IEC 61300-3-1 - Fibre optic interconnecting devices and passive components - Basic test and measurement procedures -

21、Part 3-1: Examinations and measurements - Visual examination EN 61300-3-1 - IEC 61300-3-28 - Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 3-28: Examinations and measurements - Transient loss EN 61300-3-28 - BS EN 61300-2-37:2016 2 IEC 6130

22、0-2-37:2016 IEC 2016 CONTENTS FOREWORD . 3 1 Scope 5 2 Normative references. 5 3 Terms and definitions 5 4 General description . 6 4.1 Device under test (DUT) 6 4.2 Test procedure 6 5 Apparatus 6 6 Procedure . 7 6.1 Preparation of the DUT 7 6.2 Pre-conditioning 7 6.3 Initial measurements . 7 6.4 Con

23、ditioning 7 6.5 Bending procedure 7 6.6 Recovery 8 6.7 Final measurements 8 7 Severity . 8 8 Details to be specified . 9 Bibliography . 10 Figure 1 Test apparatus . 6 Table 1 Test severities . 8 BS EN 61300-2-37:2016IEC 61300-2-37:2016 IEC 2016 3 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ FIBRE OPT

24、IC INTERCONNECTING DEVICES AND PASSIVE COMPONENTS BASIC TEST AND MEASUREMENT PROCEDURES Part 2-37: Tests Cable bending for fibre optic closures FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical com

25、mittees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technic

26、al Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmenta

27、l and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agre

28、ements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use

29、and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promot

30、e international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicat

31、ed in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) A

32、ll users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage

33、or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publica

34、tion. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such

35、 patent rights. International Standard IEC 61300-2-37 has been prepared by sub-committee 86B: Fibre optic interconnecting devices and passive components, of IEC technical committee 86: Fibre optics. This third edition cancels and replaces the second edition published in 2006. This edition constitute

36、s a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) substantial updating of Subclauses 4.1, 6.5, 6.7 and Figure 1; b) addition of severities which are determined by the number and direction of cable bends, test temperatur

37、e and overpressure for each environmental category according to IEC 61753-1. BS EN 61300-2-37:2016 4 IEC 61300-2-37:2016 IEC 2016 The text of this standard is based on the following documents: FDIS Report on voting 86B/3975/FDIS 86B/3981/RVD Full information on the voting for the approval of this st

38、andard can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. A list of all the parts in the IEC 61300 series, published under the general title, Fibre optic interconnecting devices and passive component

39、s Basic test and measurement procedures can be found on the IEC website. The committee has decided that the contents of this publication will remain unchanged until the stability date indicated on the IEC website under “http:/webstore.iec.ch“ in the data related to the specific publication. At this

40、date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. BS EN 61300-2-37:2016IEC 61300-2-37:2016 IEC 2016 5 FIBRE OPTIC INTERCONNECTING DEVICES AND PASSIVE COMPONENTS BASIC TEST AND MEASUREMENT PROCEDURES Part 2-37: Tests Cable bending for fibre optic closure

41、s 1 Scope This part of IEC 61300 describes a test for the effectiveness of the sealing and clamping hardware of a fibre optic closure when the cable entering or exiting the fibre optic closure is subjected to bending. 2 Normative references The following documents, in whole or in part, are normative

42、ly referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 61300-1, Fibre optic interconnecting devices and passive compo

43、nents Basic test and measurements procedures Part 1: General and guidance IEC 61300-2-38, Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 2-38: Tests Sealing for pressurized fibre optic closures IEC 61300-3-1, Fibre optic interconnecting devices

44、and passive components Basic test and measurement procedures Part 3-1: Examinations and measurements Visual examination IEC 61300-3-28, Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 3-28: Examinations and measurements Transient loss 3 Terms and

45、 definitions For the purposes of this document, the following terms and definitions apply. 3.1 closure enclosure intended to provide protection to splices and joints against water and dust ingress Note 1 to entry: Protection is provided by an overpressure/under-pressure sealing of at least 20 kPa or

46、 complete inner filling or free-breathing method. 3.2 climatic chamber chamber needed for conditioning the device under test 3.3 holding fixture fixture for mounting the DUT 3.4 bending device device for applying a controlled bending moment to the cable BS EN 61300-2-37:2016 6 IEC 61300-2-37:2016 IE

47、C 2016 4 General description 4.1 Device under test (DUT) The DUT is defined as an assembled closure with cable comprising all necessary parts for the required function. Separate DUTs for sealing performance and optical evaluation may be used. The sealing performance DUT shall be provided with an air

48、 pressure test access valve. The length of the cables extending from the DUT shall be at least 1 m. The open ends of the cables shall be sealed. Each applicable cable type with minimum and maximum cable dimensions shall be represented in the test program. Multiple DUTs may be required to accommodate

49、 these cables. The optical evaluation DUT shall be constructed in such a way that it represents all allowed functions of the product. This shall be realised by building optical circuits for each fibre separation level. Each applicable cable type with minimum and maximum cable dimensions shall be represented in the test program. 4.2 Test procedure The DUT shall be securely fixed and placed in a conditioning chamber. The cable shall be subjected to a specified