BS EN 61386-23-2004+A11-2010 Conduit systems for cable management Particular requirements Flexible conduit systems《电缆管理用暗线装置系统 特定要求 柔性导管系统》.pdf

1、Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 27/10/2011 07:15, Uncontrolled Copy, (c) BSIg49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58F

2、lexible conduit systemsICS 29.120.10 Conduit systems for cable management Part 23: Particular requirements BRITISH STANDARDBS EN 61386-23:2004 +A 1:20101BS EN 61386-23:2004+A11:2010Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 27/10/2011 07:15, Uncontrolled Copy, (c) BSIobtained on request

3、to its secretary.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 26 May 2004 BSI 2011ISBN 978 0 580 71474 0Amendments/corrigenda issued since publicationDate Comments 30 June 2011 Implementation of CENELEC amendment A11:2010, modification of

4、CENELEC foreword.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard cannot confer immunity from legal obligations. National forewordThis British Standard is the UK implementati

5、on of EN 61386-23:2004+A11:2010. It is identical to IEC 61386-23:2002. It supersedes BS EN 61386-23:2004, which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee PEL/213, Cable management.A list of organizations represented on this committee can be EUROPEAN ST

6、ANDARD EN 61386-23:2004+A11+A11 NORME EUROPENNE EUROPISCHE NORM December 2010 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: Avenue Marnix 17, B - 1000 Brussels 2010

7、 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 61386-23:2004 E ICS 29.120.10 Supersedes EN 50086-2-3:1995 + A11:1998English version Conduit systems for cable management Part 23: Particular requirements Flexible conduit systems (

8、IEC 61386-23:2002) Systmes de conduits pour installations lectriques Partie 23: Rgles particulires Systmes de conduits souples (CEI 61386-23:2002) Elektroinstallationsrohrsysteme fr elektrische Energie und fr Informationen Teil 23: Besondere Anforderungen fr flexible Elektroinstallationsrohrsysteme

9、(IEC 61386-23:2002) This European Standard was approved by CENELEC on 2003-09-23. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists

10、and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the resp

11、onsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hun

12、gary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. Incorporates Corrigendum April 2004 Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 27/10/2011 07:15, Uncontrolled Cop

13、y, (c) BSIForeword The text of the International Standard IEC 61386-23:2002, prepared by SC 23A, Cable management systems, of IEC TC 23, Electrical accessories, was submitted to the Unique Acceptance Procedure and was approved by CENELEC as EN 61386-23 on 2003-09-23. This European Standard supersede

14、s EN 50086-2-3:1995 + corrigendum February 2001 + A11:1998 + A11:1998/corrigendum February 2001. The following dates were fixed: latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2004-10-01 latest date by whic

15、h the national standards conflicting with the EN have to be withdrawn (dow) 2008-06-30 This part 23 supplements or modifies the corresponding clauses of EN 61386-1. Where a particular clause or subclause of part 1 is not mentioned in this part 23, that clause or subclause applies as far as is reason

16、able. Where this part 23 states “addition“, “modification“ or “replacement“, the relevant text of part 1 is to be adapted accordingly. Subclauses, tables and figures which are in addition to those in part 1 are numbered starting with 101. Additional annexes are lettered AA, BB, etc. A conduit system

17、 which complies with this standard is deemed safe for use when installed in accordance with national wiring regulations, whilst applying the manufacturers installation instructions and conduit classification. In this standard, the following print types are used: - requirements: in roman type; - test

18、 specifications: in italic type; - notes: in smaller roman type. Annexes ZAA and ZBB have been added by CENELEC. _ Endorsement notice The text of the International Standard IEC 61386-23:2002 was approved by CENELEC as a European Standard without any modification. _ Page 2This part 23, which specifie

19、s particular requirements for flexible conduit systems, is to be used in conjunction with EN 61386-1:2008; it may also be used in conjunction with EN 61386-1:2004 until EN 61386-1:2004 is withdrawn, the date of the withdrawal being no later than 2011-06-01. BS EN 61386-23:2004+A11:2010EN 61386-23:20

20、04+A11:2010 (E)Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 27/10/2011 07:15, Uncontrolled Copy, (c) BSIThis amendment (affecting only the foreword) has been issued to allow the use of EN 61386-23:2004 in conjunction with EN 61386-1:2008. Attention is drawn to the possibility that some of

21、the elements of this document may be the subject of patent rights. CEN and CENELEC shall not be held responsible for identifying any or all such patent rights. The following dates were fixed: latest date by which the amendment has to be implemented at national level by publication of an identical na

22、tional standard or by endorsement (dop) 2011-12-01 dwhsrofngwith the amendment have to be withdrawn (dow) 2013-12-01 _ Page 3BS EN 61386-23:2004+A11:2010EN 61386-23:2004+A11:2010 (E)Foreword to amendment 1This amendment to the European Standard EN 61386-23:2004 was prepared by the Technical Committe

23、e CENELEC TC 213, Cable management systems. It was submitted to the Unique Acceptance Procedure and was accepted by CENELEC as amendment A11 to EN 61386-23:2004 on 2010-12-01.Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 27/10/2011 07:15, Uncontrolled Copy, (c) BSICONTENTS 1 Scope 5 2 Norma

24、tive references .5 3 Definitions5 4 General requirements.5 5 General conditions for tests5 6 Classification5 7 Marking and documentation5 8 Dimensions 6 9 Construction.6 10 Mechanical properties 6 11 Electrical properties7 12 Thermal properties .8 13 Fire effects.8 14 External influences.8 15 Electr

25、omagnetic compatibility .8 Annex ZA (normative) Normative references to international publications with their corresponding European publications.13Figure 101 Flexing test apparatus 9 Figure 102 Gauge for checking the minimum inside diameter of the conduit system after impact and resistance to heat

26、tests . 10Figure 103 Assembly of conduit and terminating conduit fitting for bonding test 11Page 4BS EN 61386-23:2004+A11:2010EN 61386-23:2004+A11:2010 (E)Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 27/10/2011 07:15, Uncontrolled Copy, (c) BSI6831632- CEI : 2002 4 CONDUIT SYSTEMS FOR CABL

27、E MANAGEMENT Part 23: Particular requirements Flexible conduit systems 1 Scope This clause of part 1 is applicable, except as follows: Addition: This part of IEC 61386 specifies the requirements for flexible conduit systems. 2 Normative references This clause of part 1 is applicable. 3 Definitions T

28、his clause of part 1 is applicable. 4 General requirements This clause of part 1 is applicable. 5 General conditions for tests This clause of part 1 is applicable. 6 Classification This clause of part 1 is applicable, except as follows: Subclauses 6.1.3 1, 6.1.3 2 and 6.1.3 3 are not applicable. NOT

29、E Flexible conduit systems according to 6.1.1 1, 6.1.1 2, 6.1.2 1, 6.1.2 2 and classification 1X from 6.2.1, table 1 are not allowed in France. 7 Marking and documentation This clause of part 1 is applicable, except as follows: Addition: 7.1.101 The conduit shall be marked in accordance with 7.1 alo

30、ng its entire length at regular intervals of preferably 1 m but not longer than 3 m. Where this is technically impractical, the mark shall be on a label attached to the product at each end, or on the packaging. Page 5BS EN 61386-23:2004+A11:2010EN 61386-23:2004+A11:2010 (E)Licensed Copy: Wang Bin, I

31、SO/EXCHANGE CHINA STANDARDS, 27/10/2011 07:15, Uncontrolled Copy, (c) BSI6831632- CEI : 2002 5 Compliance is checked by inspection. 7.1.102 The manufacturer shall document or add to the packaging for the system the minimum inside diameter, the minimum bend radius and the classification in accordance

32、 with clause 6. Compliance is checked by inspection. 8 Dimensions Replacement: 8.1 Threads shall comply with IEC 60423. Compliance is checked by means of the gauges specified in IEC 60423. 8.2 The minimum inside diameter of the conduit system shall be as declared by the manufacturer. Compliance is c

33、hecked by measurement. 9 Construction This clause of part 1 is applicable. 10 Mechanical properties This clause of part 1 is applicable, except as follows: 10.1 Mechanical strength 10.1.1 Addition: NOTE Very light flexible conduits should not be considered as providing adequate mechanical protection

34、 and should not be used within the construction of buildings. 10.4 Bending test This subclause of part 1 is not applicable. 10.5 Flexing test 10.5.101 An assembly consisting of a conduit with a terminating conduit fitting, assembled in accordance with the manufacturers instructions, shall be subject

35、ed to a flexing test by means of the apparatus shown in figure 101. 10.5.102 The test shall be made on six samples of conduit of an appropriate length. Three of the samples shall be tested at the minimum declared transport, application and installation temperature as given in table 1 with a toleranc

36、e of 2 C. The other three samples shall be tested at the maximum declared application and installation temperature as given in table 2 with a tolerance of 2 C. Page 6BS EN 61386-23:2004+A11:2010EN 61386-23:2004+A11:2010 (E)Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 27/10/2011 07:15, Unco

37、ntrolled Copy, (c) BSI6831632- CEI : 2002 6 A manufacturer may declare that a flexible conduit is suitable for transport and installation according to table 1 but may only be suitable for flexing at ambient temperature as a minimum. In this case the test shall be carried out at (20 2) C and the 3rd

38、digit of the classification code shall be X. The manufacturer shall clearly declare in his literature both the minimum transport and installation temperature in accordance with table 1, the minimum application temperature which is ambient and the maximum installation and application temperature in a

39、ccordance with table 2. 10.5.103 The sample shall be fixed to the oscillating member by means of the terminating conduit fitting as shown in figure 101, so that when the conduit is at the middle of its travel, the axis of the conduit is vertical and passes through the axis of the oscillation. The ap

40、paratus with the sample shall be conditioned for 2 h or until the sample has attained the declared temperature, whichever period is the longer. 10.5.104 The oscillating member shall be moved backwards and forwards through a total angle of (180 5) divided equally about the vertical axis. The assembly

41、 shall be subjected to 5 000 flexings at a rate of (40 5) flexings per minute. A flexing constitutes, starting from the vertical position, one continuous cycle of movement of essentially sinusoidal forms. 10.5.105 After the test, the sample shall show no sign of disintegration, nor shall there be an

42、y cracks visible to normal or corrected vision without magnification. 10.6 Collapse test This subclause of part 1 is not applicable. 10.7 Tensile strength This subclause of part 1 is applicable, except as follows: 10.7.3 Replacement: For conduit systems where tensile strength is not declared, the te

43、nsile strength of the joint shall comply with classification 1 in table 6. 11 Electrical properties This clause of part 1 is applicable, except as follows: 11.2 Bonding test Replacement: A sample of a conduit and terminating conduit fitting shall be assembled in accordance with the manufacturers ins

44、tructions and mounted as shown in figure 103. A current of 25 A, having a frequency of 50 Hz to 60 Hz, derived from an a.c. source having a no-load voltage not exceeding 12 V, shall be passed through the assembly for (5060+) s. Then the voltage drop shall be measured between the points shown in figu

45、re 103 and the resistance calculated from the current and this voltage drop. The resistance shall not exceed 0,05 . Page 7BS EN 61386-23:2004+A11:2010EN 61386-23:2004+A11:2010 (E)Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 27/10/2011 07:15, Uncontrolled Copy, (c) BSI6831632- CEI : 2002 7

46、Where special devices are required for the coupling of conduit and conduit fittings, they shall be sufficient to remove the protective coating from the conduit, or the protective finish shall be removed in accordance with the manufacturers instructions. 12 Thermal properties This clause of part 1 is

47、 applicable, except as follows: 12.2.4 Replacement: The load is then removed and immediately after its removal it shall be possible to pass the appropriate gauge, in accordance with figure 102, through the conduit under its own weight and without any initial speed, with the sample in the vertical po

48、sition. 13 Fire effects This clause of part 1 is applicable. 14 External influences This clause of part 1 is applicable. 15 Electromagnetic compatibility This clause of part 1 is applicable. Page 8BS EN 61386-23:2004+A11:2010EN 61386-23:2004+A11:2010 (E)Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA ST

49、ANDARDS, 27/10/2011 07:15, Uncontrolled Copy, (c) BSI6831632- CEI : 2002 8 dn32dsR1R2dsY2ZBA90901Key A Conduit B Terminating fitting dsOutside diameter of conduit (A) dnInside diameter of support block: 1,1 dsR1Radius of support block: 0,5 d, R2Radius of support block: 0,25 dsY Minimum bend radius, declared by the manufacturer Z 1,5 Y 1 Oscillating member 2 Guide support block 3 Plan view of guide support block NOTE This drawing is not intended to govern design except as reg