BS EN 61988-2-1-2012 Plasma display panels Measuring methods Optical and optoelectrical《等离子体显示板 测量方法 光学和光电》.pdf

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationPlasma display panelsPart 2-1: Measuring methods Optical and optoelectricalBS EN 61988-2-1:2012National forewordThis British Standard is the UK implementation of EN 61988-2-1:201

2、2. It isidentical to IEC 61988-2-1:2012. It supersedes BS EN 61988-2-1:2002 and BSEN 61988-2-2:2003, which are withdrawn.The UK participation in its preparation was entrusted to Technical CommitteeEPL/47, Semiconductors.A list of organizations represented on this committee can be obtained onrequest

3、to its secretary.This publication does not purport to include all the necessary provisions of acontract. Users are responsible for its correct application. The British Standards Institution 2012Published by BSI Standards Limited 2012ISBN 978 0 580 65877 8ICS 31.260 Compliance with a British Standard

4、 cannot confer immunity fromlegal obligations.This British Standard was published under the authority of the StandardsPolicy and Strategy Committee on 30 April 2012.Amendments issued since publicationAmd. No. Date Text affectedBRITISH STANDARDBS EN 61988-2-1:2012EUROPEAN STANDARD EN 61988-2-1 NORME

5、EUROPENNE EUROPISCHE NORM March 2012 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Management Centre: Avenue Marnix 17, B - 1000 Brussels 2012 CENELEC - All rights of exploitation in an

6、y form and by any means reserved worldwide for CENELEC members. Ref. No. EN 61988-2-1:2012 E ICS 31.260 Supersedes EN 61988-2-1:2002, EN 61988-2-2:2003English version Plasma display panels - Part 2-1: Measuring methods - Optical and optoelectrical (IEC 61988-2-1:2012) Panneaux daffichage plasma - Pa

7、rtie 2-1: Mthodes de mesure - Mesures optiques et opto-lectriques (CEI 61988-2-1:2012) Plasmabildschirme - Teil 2-1: Messverfahren Optisch und opto-elektrisch (IEC 61988-2-1:2012) This European Standard was approved by CENELEC on 2012-02-28. CENELEC members are bound to comply with the CEN/CENELEC I

8、nternal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to

9、any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the

10、official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Pol

11、and, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 61988-2-1:2012EN 61988-2-1:2012 - 2 - Foreword The text of document 110/337/FDIS, future edition 2 of IEC 61988-2-1, prepared by IEC TC 110, “Flat panel display devices“ was submitted to the

12、IEC-CENELEC parallel vote and approved by CENELEC as EN 61988-2-1:2012. The following dates are fixed: latest date by which the document has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2012-11-28 latest date by which the national stand

13、ards conflicting with the document have to be withdrawn (dow) 2015-02-28 This document supersedes EN 61988-2-1:2002 and EN 61988-2-2:2003. EN 61988-2-1:2012 includes the following significant technical changes with respect to EN 61988-2-1:2002: EN 61988-2-1:2002 and EN 61988-2-2:2003 were combined a

14、nd reconstructed in this document. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC and/or CEN shall not be held responsible for identifying any or all such patent rights. Endorsement notice The text of the International St

15、andard IEC 61988-2-1:2012 was approved by CENELEC as a European Standard without any modification. In the official version, for Bibliography, the following notes have to be added for the standards indicated: IEC 61988-2-1 NOTE Harmonized as EN 61988-2-1. IEC 61988-2-2 NOTE Harmonized as EN 61988-2-2

16、. BS EN 61988-2-1:2012- 3 - EN 61988-2-1:2012 Annex ZA (normative) Normative references to international publications with their corresponding European publications The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. Fo

17、r dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. Publication

18、Year Title EN/HD Year IEC 60068-1 - Environmental testing - Part 1: General and guidance EN 60068-1- IEC 60107-1 - Methods of measurement on receivers for television broadcast transmissions - Part 1: General considerations - Measurements at radio and video frequenciesEN 60107-1 - IEC 61988-1 - Plasm

19、a display panels - Part 1: Terminology and letter symbols EN 61988-1 - IEC 62087 - Methods of Measurement for the power consumption of audio, video and related equipment EN 62087 - CIE 15 - Colorimetry - - BS EN 61988-2-1:2012 2 61988-2-1 IEC:2012 CONTENTS 1 Scope . 6 2 Normative references . 6 3 Te

20、rms and definitions . 6 4 Structure of measuring equipment 7 5 Standard measuring conditions . 7 5.1 Environmental conditions 7 5.2 Set-up conditions 7 5.2.1 General . 7 5.2.2 Measuring layout . 8 5.2.3 Field frequency 8 5.2.4 Adjustment of PDP modules 9 5.2.5 Warm-up condition of PDP modules 9 5.3

21、Lighting conditions 9 5.3.1 Dark-room conditions 9 5.3.2 Bright-room conditions . 9 6 Measuring methods 11 6.1 Measuring methods of 4 % window luminance . 11 6.1.1 Purpose . 11 6.1.2 Measuring equipment 11 6.1.3 Measurement. 11 6.2 Measuring method of luminance uniformity 12 6.2.1 Purpose . 12 6.2.2

22、 Measuring equipment 12 6.2.3 Measurement. 12 6.3 Measuring method of dark-room contrast ratio . 13 6.3.1 Purpose . 13 6.3.2 Measuring equipment 13 6.3.3 Measurement. 14 6.4 Measuring method of bright-room contrast ratio 100/70 . 15 6.4.1 General . 15 6.4.2 Purpose . 15 6.4.3 Measuring equipment 15

23、6.4.4 Measurement. 15 6.5 Measuring method of white chromaticity and chromatic uniformity . 16 6.5.1 Purpose . 16 6.5.2 Measuring equipment 16 6.5.3 Measurement. 16 6.6 Measuring method of colour gamut 17 6.6.1 Purpose . 17 6.6.2 Measuring equipment 17 6.6.3 Measurement. 17 6.7 Measuring method of m

24、odule power and current consumption . 18 6.7.1 Purpose . 18 6.7.2 Measuring equipment 18 6.7.3 Measurement. 19 BS EN 61988-2-1:201261988-2-1 IEC:2012 3 6.8 Measuring method of module power consumption using video signal . 21 6.8.1 General . 21 6.8.2 Measuring equipment 21 6.8.3 Applied digital video

25、 signal 21 6.8.4 Image processing board 21 6.8.5 Measurement. 22 6.9 Measuring method of module luminous efficacy . 23 6.9.1 Purpose . 23 6.9.2 Measuring equipment 23 6.9.3 Measurement. 23 6.10 Measuring method of panel luminous efficacy . 24 6.10.1 Purpose . 24 6.10.2 Measuring equipment 24 6.10.3

26、Panel conditions 25 6.10.4 Driving waveform . 26 6.10.5 Applied display patterns 27 6.10.6 Measurement. 27 Annex A (informative) Clause cross-references from the previous edition of IEC 61988-2-1:2002 and IEC 61988-2-2:2003 to IEC 61988-2-1:2011. 31 Bibliography 33 Figure 1 Measuring layout (side vi

27、ew) 8 Figure 2 Example of bright-room conditions . 10 Figure 3 4 % window luminance measuring pattern 11 Figure 4 Measuring points 13 Figure 5 Minimum luminance measuring pattern 15 Figure 6 Example of the colour gamut measurement 18 Figure 7 Example of power and current measuring diagram . 19 Figur

28、e 8 System diagram of sustain power measurement . 25 Figure 9 Driving system and waveform . 27 Table 1 Example of luminance uniformity measurement . 13 Table 2 Example of chromaticity measurement 17 Table 3 Example of power and current measurements (for a module that includes an AC input) 20 Table 4

29、 Example of power and current measurement (for a module with DC inputs only) . 20 Table 5 Example of measurement results of module power consumption using video signal 22 Table A.1 Clause cross-references . 32 BS EN 61988-2-1:2012 6 61988-2-1 IEC:2012 PLASMA DISPLAY PANELS Part 2-1: Measuring method

30、s Optical and optoelectrical 1 Scope This part of IEC 61988 determines the following measuring methods for characterizing the performance of plasma display modules (PDP modules): a) four per cent (4 %) window luminance; b) luminance uniformity; c) dark-room contrast ratio; d) bright-room contrast ra

31、tio 100/70; e) white chromaticity and chromatic uniformity; f) colour gamut in the centre box; g) module power and current consumption; h) module power consumption using video signal; i) module luminous efficacy, and j) panel luminous efficacy. 2 Normative references The following documents, in whol

32、e or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60068-1, Environmental Testing Part

33、 1: General and guidance IEC 60107-1, Methods of measurement on receivers for television broadcast transmissions Part 1: General considerations Measurements at radio and video frequencies IEC 61988-1, Plasma display panels Part 1: Terminology and letter symbols IEC 62087, Methods of measurement for

34、the power consumption of audio, video and related equipment CIE 15:2004, Colorimetry 3 Terms and definitions For the purposes of this document, the terms and definitions given in IEC 61988-1, IEC 60068-1, and IEC 60107-1, as well as the following, apply. BS EN 61988-2-1:201261988-2-1 IEC:2012 7 3.1

35、4 % window panel luminous efficacy p0,04panel luminous efficacy measured by displaying the patterns of 4 % white window and full screen black NOTE Ohmic loss is smaller than that of full screen panel luminous efficacy (see 3.4). 3.2 full screen panel luminous efficacy p,fspanel luminous efficacy mea

36、sured by displaying the patterns of full screen white and full screen black NOTE Ohmic loss is larger than that of 4 % window panel luminous efficacy (see 3.4). 3.3 panel checker system used to drive and test plasma display panel NOTE Panel checker includes the same or the equivalent electric circui

37、ts as a PDP module. 3.4 panel luminous efficacy luminous efficacy incremental luminous flux (measured as the luminous flux of a white display minus the luminous flux of a black display) divided by the incremental power input applied to the sustain driver for operating the panel (measured as the whit

38、e display power minus the black display power) NOTE Expressed in lumens/watt. 4 Structure of measuring equipment The system diagrams and/or driving conditions of the measuring equipment shall comply with the structure specified in each item. 5 Standard measuring conditions 5.1 Environmental conditio

39、ns Measurements shall be carried out under the standard environmental conditions, i.e. at a temperature of 25 C 3 C, a relative humidity of 25 % to 85 %, and a pressure of 86 kPa to 106 kPa. When different environmental conditions are used, these shall be noted on the report. 5.2 Set-up conditions 5

40、.2.1 General The following standard set-up conditions shall be used. Each condition shall be noted on the relevant specification whenever any different conditions other than the standard set-up conditions are applied. BS EN 61988-2-1:2012 8 61988-2-1 IEC:2012 5.2.2 Measuring layout 5.2.2.1 General M

41、easurements shall be carried out at the standard measuring layout shown in Figure 1. When a different measuring layout is used, this shall be noted on the report. 5.2.2.2 Position of light measuring device The light measuring device shall be aligned perpendicular to the area to be measured on the sc

42、reen of the PDP module. 5.2.2.3 Standard measuring distance The standard measuring distance xois 2,5 V, where V is the screen height or the short side length of the screen. The measuring distance shall be between 1,6 V and 2,8 V. The measuring distance shall be noted on the report. 5.2.2.4 Aperture

43、angle of light measuring device The light measuring device shall be set at a proper aperture angle less than or equal to 2 degrees, and shall measure an area of at least 500 pixels which has an extent less than 10 % of the screen height. This area corresponds to including a circular measurement area

44、 of at least 26 lines in diameter in the case of a display panel having a square pixel consisting of 3 subpixels. The measuring distance and the aperture angle may be adjusted to achieve a viewing area greater than 500 pixels, which has an extent less than 10 % of the screen height if setting the ab

45、ove aperture angle is difficult. Such deviations from standard conditions shall be noted on the report. Key X0standard measuring distance = 2,5 V, where V is the screen height or short side length of screen. Figure 1 Measuring layout (side view) 5.2.3 Field frequency The standard field frequency of

46、the driving signal equipment shall be 60 Hz, unless the module is intended to be used at a significantly different frequency. In any case, the field frequency used shall be noted on the report. Driving signal equipment Driving power source Light measuring device Display surface Plasma display module

47、 XoMeasuring point Perpendicular to screen IEC 44/12 BS EN 61988-2-1:201261988-2-1 IEC:2012 9 5.2.4 Adjustment of PDP modules For contrast adjustable PDP modules, adjust the contrast to the maximum value under the standard environmental conditions. Automatic control functions such as auto-power cont

48、rol (APC), image sticking prevention function, etc. by which the display luminance could change during the measurement shall be turned off or the activation of these functions shall be avoided by some measuring procedures described below. When the displayed luminance could be changed by some automat

49、ic control functions included in the PDP module and turning off these functions is not convenient, a procedure using sequentially changing input images or a procedure using a turn-on, measure and turn-off sequence shall be applied. For the procedure of sequentially changing input images, the input signals shall be changed just before the display luminance is changed and the measurement shall be carried out when the measured image is displayed. The input signa