BS EN 62343-2013 Dynamic modules General and guidance《动态模块 总则和指引》.pdf

1、BSI Standards PublicationDynamic modules General and guidanceBS EN 62343:2013National forewordThis British Standard is the UK implementation of EN 62343:2013. It is identical to IEC 62343:2013.The UK participation in its preparation was entrusted by TechnicalCommittee GEL/86, Fibre optics, to Subcom

2、mittee GEL/86/3, Fibre optic systems and active devices.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisions ofa contract. Users are responsible for its correct application. The Brit

3、ish Standards Institution 2013.Published by BSI Standards Limited 2013ISBN 978 0 580 69784 5ICS 33.180.01; 33.180.99Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on

4、 30 September 2013.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN 62343:2013EUROPEAN STANDARD EN 62343 NORME EUROPENNE EUROPISCHE NORM August 2013 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Eu

5、ropisches Komitee fr Elektrotechnische Normung CEN-CENELEC Management Centre: Avenue Marnix 17, B - 1000 Brussels 2013 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 62343:2013 E ICS 33.180.01; 33.180.99 English version Dynamic m

6、odules - General and guidance (IEC 62343:2013) Modules dynamiques - Gnralits et lignes directrices (CEI 62343:2013) Dynamische Module - Allgemeines und Leitfaden (IEC 62343:2013) This European Standard was approved by CENELEC on 2013-07-10. CENELEC members are bound to comply with the CEN/CENELEC In

7、ternal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to a

8、ny CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the o

9、fficial versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembour

10、g, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 62343:2013EN 62343:2013 - 2 - Foreword The text of document 86C/1055/CDV, future edition 1 of IEC 62343, prepared by SC 86C “Fibre optic systems and acti

11、ve devices“ of IEC TC 86 “Fibre optics“ was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN 62343:2013. The following dates are fixed: latest date by which the document has to be implemented at national level by publication of an identical national standard or by endorsement

12、 (dop) 2014-04-10 latest date by which the national standards conflicting with the document have to be withdrawn (dow) 2016-07-10 Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC and/or CEN shall not be held responsible for

13、 identifying any or all such patent rights. Endorsement notice The text of the International Standard IEC 62343:2013 was approved by CENELEC as a European Standard without any modification. In the official version, for Bibliography, the following notes have to be added for the standards indicated: I

14、EC 61290 NOTE Harmonised as EN 61290 (series). IEC 61291 NOTE Harmonised as EN 61291 (series). IEC 61300 NOTE Harmonised as EN 61300 (series). IEC 61753 NOTE Harmonised as EN 61753 (series). IEC 62342-2 NOTE Harmonised as EN 62342-2. IEC 62343-3-1:2010 NOTE Harmonised as EN 62343-3-1:2010 (not modif

15、ied). IEC 62343-5 NOTE Harmonised as EN 62343-5 (series). BS EN 62343:2013- 3 - EN 62343:2013 Annex ZA (normative) Normative references to international publications with their corresponding European publications The following documents, in whole or in part, are normatively referenced in this docume

16、nt and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE When an international publication has been modified by common modifications, indicated by

17、 (mod), the relevant EN/HD applies. Publication Year Title EN/HD Year IEC 60050-731 - International Electrotechnical Vocabulary (IEV) - Chapter 731: Optical fibre communication - - IEC/TR 61931 - Fibre optic - Terminology - - IEC 62343-1 series Dynamic modules - Performance standards EN 62343-1 seri

18、es IEC 62343-3 series Dynamic modules - Performance specification templates EN 62343-3 series IEC Guide 107 - Electromagnetic compatibility - Guide to the drafting of electromagnetic compatibility publications - - BS EN 62343:2013 2 62343 IEC:2013(E) CONTENTS INTRODUCTION . 5 1 Scope and object 7 2

19、Normative references . 7 3 Terms and definitions . 7 3.1 General terms . 8 3.2 Dynamic module terms 8 3.3 Dynamic channel equalizer (DCE) terms . 8 3.4 Tuneable dispersion compensator (TDC) or dynamic chromatic dispersion compensator (DCDC) terms . 9 3.5 Dynamic gain tilt equalizer (DGTE) terms 10 3

20、.6 Optical channel monitor (OCM) terms 11 4 Abbreviations . 14 5 Preparation of standards 14 5.1 General . 14 5.2 Product definition 15 5.3 Tests . 15 5.4 Details . 15 5.5 Requirements 15 5.6 Sample size 15 5.7 Sample definition . 15 5.8 Groupings/sequences 15 5.9 Pass/fail criteria 15 5.10 Referenc

21、e product definition 15 5.11 Performance standard test report 15 6 Electromagnetic compatibility (EMC) requirements . 16 Bibliography 17 BS EN 62343:201362343 IEC:2013(E) 5 INTRODUCTION This International Standard applies to dynamic devices as defined in IEC/TS 62538. It contains general guidance fo

22、r the IEC 62343 series related to dynamic devices, and definitions which apply to dynamic devices. The dynamic module, or device, has two distinguishing characteristics: dynamic and module. “Dynamic” highlights the functions of the products to include “tuning, varying, switching, configuring, and ot

23、her continuous optimization,” often accomplished by electronics, firmware, software or their combinations. The dynamic device usually has a certain level of intelligence to monitor or measure the situation and make decisions for necessary (optimization) actions. The behaviour of dynamic modules may

24、be characterized by transient characteristics as the dynamic module undergoes tuning, switching, configuring and other continuous optimization. Characterization of transient characteristics will be considered in individual dynamic module standards. “Module” defines that the products covered by the s

25、tandard are the integration of active and passive components (either or both), through interconnecting materials or devices. The controlling electronics can be inside or outside the optical package (that contains all or most of the optical components and interconnection). The product can look like a

26、 small printed wiring board (PWB or child-board with mounted optical module) or a small box (housing) with optical components and electronics enclosed. In the former case, it is more like an assembly (generally not packaged in a box or housing) than a module (generally packaged in a box or housing).

27、 For historical reasons and convenience, a dynamic module or device is referred to as a dynamic module in the IEC 62343-X series. The number of dynamic modules and devices is rapidly growing as optical communications networks evolve. The following list provides some examples of the products covered

28、by the IEC 62343-X series. It should be noted that the list is not exhaustive and the products to be covered are not limited by the listed examples: channel gain equalizer; dynamic channel equalizer; dynamic gain tilt equalizer; dynamic slope equalizer; tuneable chromatic dispersion compensator; pol

29、arization mode dispersion compensator; reconfigurable optical add-drop multiplexer; switch with monitoring and controls; variable optical attenuator with monitoring and controls. The IEC 62343 series will cover performance templates, performance standards, reliability qualification requirements, har

30、dware and software interfaces, and related testing methods. A complete set of standards related to a dynamic module or device should include the following: optical performance standards; reliability qualification standards; optical performance specification templates; hardware and software interface

31、 standards; test methods; BS EN 62343:2013 6 62343 IEC:2013(E) technical reports. The safety standards related to dynamic modules are mostly optical power considerations, which are covered by IEC TC 76: Optical radiation safety and laser equipment. Only those dynamic modules for which standards are

32、complete or in preparation are included in Clause 3. To reflect the rapidly growing market for dynamic modules, additional terms and definitions will be added in subsequent revisions as the series expands. It should be noted that optical amplifiers could be regarded as dynamic modules. They are not

33、included in the IEC 62343-X series, but are covered in their own series of IEC standards. BS EN 62343:201362343 IEC:2013(E) 7 DYNAMIC MODULES GENERAL AND GUIDANCE 1 Scope and object This International Standard applies to all commercially available optical dynamic modules and devices. It describes th

34、e products covered by the IEC 62343-X series, defines terminology, fundamental considerations and basic approaches. The object of this standard is to establish uniform requirements for operation, reliability and environmental properties of DMs to be implemented in the appropriate DM standard, provid

35、e assistance to the purchaser in the selection of consistently high-quality DM products for his particular applications, as well as in the consultation of the appropriate specific DM standard(s). This standard covers performance templates, performance standards, reliability qualification requirement

36、s, hardware and software interfaces and related testing methods. Since a dynamic module integrates an optical module/device, printed wiring board, and software/firmware, the standards developed in the series will mimic appropriate existing standards. On the other hand, since “dynamic module“ is a re

37、latively new product category, the dynamic module standards series will not be bounded by the existing practices where requirements differ. The safety standards as related to dynamic modules are mostly optical power considerations, which is covered by IEC TC 76: Optical radiation safety and laser eq

38、uipment. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including

39、any amendments) applies. IEC 60050-731, International Electrotechnical Vocabulary Chapter 731: Optical fibre communication IEC/TR 61931, Fibre optic Terminology IEC 62343-1 (all parts), Dynamic modules Optical performance standards IEC 62343-3 (all parts), Dynamic modules Optical performance specifi

40、cation templates IEC Guide 107, Electromagnetic compatibility Guide to the drafting of electromagnetic compatibility publications 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. BS EN 62343:2013 8 62343 IEC:2013(E) The definitions listed in this

41、clause refer to the meaning of the terms used in the specifications of DMs. Only those parameters listed in the appropriate performance standard in the IEC 62343-1 series and performance specification templates in the IEC 62343-3 series are intended to be specified. The list of parameter definitions

42、 of DMs, given in this clause, is divided into subclauses by the type of DM. See also IEC 60050-731and IEC/TR 61931. 3.1 General terms 3.1.1optical dynamic device optical device which is designed to monitor and control dynamically some characteristics of one or more optical signals, by means of suit

43、able electronic controls, in order to improve or to maintain definite performances of the system in which it is intended to be inserted Note 1 to entry: Said characteristics may include optical paths, optical intensities, spectral characteristics, polarization states, dispersion, etc. Note 2 to entr

44、y: Optical dynamic devices may comprise optical active and optical passive elements or components. Note 3 to entry: The control/response time of optical dynamic devices is much larger than the signal time characteristics and typically may range from few microseconds to tens of seconds. SOURCE: IEC/T

45、S 62538:2008, definition 2.1.1 3.1.2optical module packaged integration of optical components and/or elements, accomplishing defined functionality, typically repairable and re-workable SOURCE: IEC/TS 62538:2008, definition 2.2.5, modified the Notes to entry in the source have been omitted 3.2 Dynami

46、c module terms The following definitions apply to all dynamic modules 3.2.1operating wavelength range specified range of wavelengths from iminto imaxabout a nominal operating wavelength I, within which a dynamic optical module is designed to operate with a specified performance 3.2.2channel frequenc

47、y range frequency range within which a device is expected to operate with a specified performance Note 1 to entry: For a particular nominal channel central frequency, fnomi, this frequency range is from fimin= (fnomi- fmax) to fimax= (fnomi+ fmax), where fmax is the maximum channel central frequency

48、 deviation. 3.2.3channel spacing centre-to-centre difference in frequency (or wavelength) between adjacent channels in a device 3.3 Dynamic channel equalizer (DCE) terms The following definitions apply to the dynamic channel equalizer BS EN 62343:201362343 IEC:2013(E) 9 3.3.1dynamic channel equalize

49、r DCE device capable of transforming, by internal or external automatic control, a multichannel input signal with time-varying averaged powers into an output signal in which all working channel powers are nominally equal or are set for a required level of pre-emphasis Note 1 to entry: This device may also provide the extinction of one or more of the input channels. SOURCE: IEC 62343-3-1:2010, definition 3.5 3.3.2channel non-uniformity difference between the powers of the