BS EN ISO 105-G01-2016 Textiles Tests for colour fastness Colour fastness to nitrogen oxides《纺织品 色牢度试验 第G01部分 耐氧化氮的色牢度》.pdf

1、BS EN ISO 105-G01:2016T e x t i l e s T e s t s f o r c o l o u rfastnessPart G01: Colour fastness to nitrogenoxides (ISO 105-G01:2016)BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06BS EN ISO 105-G01:2016 BRITISH STANDARDNational forewordThis British Standard is the

2、 UK implementation of EN ISO105-G01:2016. It supersedes BS EN ISO 105-G01:1996 which iswithdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee TCI/81, Colour fastness and colour measurement oftextiles.A list of organizations represented on this committee can beobtained

3、on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2016.Published by BSI Standards Limited 2016ISBN 978 0 580 84758 5ICS 59.080.01Compliance with a Bri

4、tish Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 30 June 2016.Amendments/corrigenda issued since publicationDate T e x t a f f e c t e dEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM

5、 EN ISO 105-G01 June 2016 ICS 59.080.01 Supersedes EN ISO 105-G01:1995English Version Textiles - Tests for colour fastness - Part G01: Colour fastness to nitrogen oxides (ISO 105-G01:2016) Textiles - Essais de solidit des teintures - Partie G01: Solidit des teintures aux oxydes dazote (ISO 105-G01:2

6、016) Textilien - Farbechtheitsprfungen - Teil G01: Farbechtheit gegen Stickoxide (ISO 105-G01:2016) This European Standard was approved by CEN on 12 May 2016. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard th

7、e status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, Fren

8、ch, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria,

9、 Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey

10、andUnited Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2016 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref.

11、No. EN ISO 105-G01:2016 EBS EN ISO 105-G01:2016EN ISO 105-G01:2016 (E) 3 European foreword This document (EN ISO 105-G01:2016) has been prepared by Technical Committee ISO/TC 38 “Textiles“ in collaboration with Technical Committee CEN/TC 248 “Textiles and textile products” the secretariat of which i

12、s held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by December 2016, and conflicting national standards shall be withdrawn at the latest by December 2016. Attention is drawn to the possib

13、ility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN ISO 105-G01:1995. According to the CEN-CENELEC Internal Regulations, the national standard

14、s organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxem

15、bourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. Endorsement notice The text of ISO 105-G01:2016 has been approved by CEN as EN ISO 105-G01:2016 without any modification. BS EN ISO 105-G01:2016ISO 105-G01:201

16、6(E)Foreword iv1 Scope . 12 Normative references 13 Principle 14 Apparatus and materials 15 Conditioning and testing atmosphere 36 Test specimens 37 Procedure. 37.1 Preliminary operations 37.2 One-cycle test . 37.3 Three-cycle test 47.4 Conditioning 48 Test report . 4Annex A (normative) Test apparat

17、us . 6Annex B (normative) Nitric oxide generation apparatus 8Bibliography .10 ISO 2016 All rights reserved iiiContents PageBS EN ISO 105-G01:2016ISO 105-G01:2016(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodi

18、es). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and

19、non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are desc

20、ribed in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).Attention is drawn t

21、o the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the

22、ISO list of patent declarations received (see www.iso.org/patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, a

23、s well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information.The committee responsible for this document is ISO/TC 38, Textiles, Subcommittee SC 1, Tests for coloured textiles and colorants.This

24、third edition cancels and replaces the second edition (ISO 105-G01:1993), which has been technically revised. It also incorporates the Technical Corrigendum ISO 105-G01:1993/Cor 1:1995. The main technical changes are the following:a) the test-control fabric dyed with Disperse Blue 3 was deleted;b) t

25、he test-control fabric dyed with Disperse Violet 1 and the test-control fabric dyed with DisperseBlue 56 were added.ISO 105 consists of many parts designated by a part letter and a two-digit serial number (e.g. A01), under the general title Textiles Tests for colour fastness. A complete list of thes

26、e is given in ISO 105-A01.iv ISO 2016 All rights reservedBS EN ISO 105-G01:2016INTERNATIONAL STANDARD ISO 105-G01:2016(E)Textiles Tests for colour fastness Part G01: Colour fastness to nitrogen oxides1 ScopeThis part of ISO 105 specifies two methods for determining the resistance of the colour of te

27、xtiles of all kinds and in all forms to the action of nitrogen oxides produced during combustion of gas, coal, oil, etc., and when air is passed over heated filaments.The two tests differ in severity; one or both of them are used, depending on the result obtained (7.2.4).2 Normative referencesThe fo

28、llowing documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 105-A02, T

29、extiles Tests for colour fastness Part A02: Grey scale for assessing change in colourISO 105-F02, Textiles Tests for colour fastness Part F02: Specification for cotton and viscose adjacent fabricsISO 139, Textiles Standard atmospheres for conditioning and testingISO 3696, Water for analytical labora

30、tory use Specification and test methods3 PrincipleSpecimens of textiles are exposed to nitrogen oxides in a closed container until either one or three test-control fabrics exposed simultaneously with the test specimens have changed in colour to a predetermined extent. The change in colour of each sp

31、ecimen is assessed with the grey scale.4 Apparatus and materials4.1 Exposure chamber, see Annex A.4.2 Nitric oxide, from a commercially supplied cylinder or a generator (see Annex B).WARNING Nitric oxide is toxic. The maximum concentration in a working room should not exceed 6,7 mg/m3.4.3 Sulfuric a

32、cid, containing 1 100 g/l of H2SO4(relative density 1,603).4.4 Sodium nitrite (NaNO2), saturated solution in grade 3 water (4.13).4.5 Sodium hydroxide, dilute solution (approximately 100 g/l of NaOH). ISO 2016 All rights reserved 1BS EN ISO 105-G01:2016ISO 105-G01:2016(E)4.6 Urea solution, containin

33、g 10 g/l of urea (NH2CONH2), buffered to pH 7 by the addition of 0,4 g/l of sodium dihydrogen orthophosphate dihydrate (NaH2PO42H2O) and 2,5 g/l of disodium hydrogen orthophosphate dodecahydrate (Na2HPO412H2O), and containing 0,1 g/l or less of a rapid-wetting surface-active agent, for example, sodi

34、um dioctyl sulfosuccinate.4.7 Test-control fabric4.7.1 Test-control fabric dyed with Disperse Violet 1A woven filament acetate is uniformly dyed in an open-width dyeing machine with 0,4 % (on mass of fabric) Cl Disperse Violet 1 (Colour Index, Third Edition) in a dye-bath containing 1 g/l of a dispe

35、rsing agent at a liquor ratio of 10:1.The fabric construction has both a taffeta and a satin side; for this test procedure, only the taffeta side will be considered.The resistance of the test-control fabric to the action of nitric oxide should not be varied between the new lots. The supplier should

36、confirm the performance of the new lot.1)4.7.2 Test-control fabric dyed with Disperse Blue 56A woven filament acetate is uniformly dyed in an open-width dyeing machine with 0,8 % (on mass of fabric) CI Disperse Blue 56 (Colour Index, Third Edition) in a dye-bath containing 0,5 ml/l of a dispersing a

37、gent at a liquor ratio of 42:1.The fabric construction has both a taffeta and a satin side; for this test procedure, only the taffeta side will be considered.The resistance of the test-control fabric to the action of nitric oxide should not be varied between the new lots. The supplier should confirm

38、 the performance of the new lot.2)4.8 Standard of fading4.8.1 Standard fading fabric for test-control fabric dyed with Disperse Violet 1The regenerated cellulose woven taffeta is a fabric of similar appearance to the test-control fabric (4.7.1), dyed to match an average of faded test-control fabric.

39、3)4.8.2 Standard of fading for test-control fabric dyed with Disperse Blue 56It is considered that the standard of fading is completed when a faded test-control fabric (4.7.2) is observed to have a contrast equal to grade 3-4 on the grey scale.4.9 Syringe, for injecting oxide into the exposure chamb

40、er (4.1).A medical syringe is best suited to the injection of the nitric oxide. For a larger exposure chamber, the gas can also be measured and transferred from the nitric oxide reservoir to the exposure chamber by means of a gas burette.4.10 Undyed fabric, of the same kind(s) of fibre as the test s

41、pecimen.1) Test-control fabric dyed with Disperse Violet 1 is commercially available from Testfabrics, Inc. This informationis given for the convenience of users of this document and does not constitute an endorsement by ISO this product.2) Test-control fabric dyed with Disperse Blue 56 is commercia

42、lly available from the Japanese StandardsAssociation. This information is given for the convenience of users of this document and does not constitute an endorsement by ISO this product.3) The standard fading fabric is commercially available from Testfabrics, Inc. This information is given for thecon

43、venience of users of this document and does not constitute an endorsement by ISO this product.2 ISO 2016 All rights reservedBS EN ISO 105-G01:2016ISO 105-G01:2016(E)4.11 Grey scale for assessing change in colour, complying with ISO 105-A02.4.12 Means for providing the standard atmosphere for testing

44、, specified in Clause 5.4.13 Grade 3 water, according to ISO 3696.5 Conditioning and testing atmosphereThe standard temperate atmosphere for testing textiles (see ISO 139), i.e. a relative humidity of (65 4) % and temperature of (20 2) C, shall be used for conditioning and testing.6 Test specimens6.

45、1 If the textile to be tested is fabric, use a test specimen measuring 40 mm 100 mm.6.2 If the textile to be tested is yarn, knit it into fabric and use a piece measuring 40 mm 100 mm or wind it closely round a frame of rigid inert material measuring 40 mm 100 mm to form, on each side, a layer havin

46、g only the thickness of the yarn.6.3 If the textile to be tested is loose fibre, comb and compress enough of it to form a sheet measuring 40 mm 100 mm and sew the sheet on a piece of cotton adjacent fabric complying with ISO 105-F02 to support the fibre.6.4 Cut a test specimen measuring 40 mm 100 mm

47、 from the test-control fabric (4.7.1 or 4.7.2) and cut test specimens measuring 40 mm 100 mm from the undyed fabric (4.10).7 Procedure7.1 Preliminary operations7.1.1 Mount each test specimen by fastening the shorter side to a radial arm of the frame of the apparatus (see Figure A.1) by means of an a

48、dhesive or clips. When an adhesive is used, this shall be allowed to dry properly.7.1.2 Up to 12 test specimens, each measuring 40 mm 100 mm, may be mounted in this way for one test. If fewer test specimens are to be tested, fill up with cuttings of undyed fabric of the same kind to the total number

49、 of 12. The test-control fabric is fastened to the holder. Condition the test specimens and test-control fabric for at least 12 h in the atmosphere specified in Clause 5.7.1.3 Place the frame with the test specimens inside the glass cylinder and then place the bell-jar on top; put the holder with the test-control fabric through the top plug-hole.7.1.4 Adjust the rotational frequency of the fan to 200 min-1to 300 min-1and shield the apparatus from bright light.7.1.5 Inject 0,65 ml of nitric oxide (4.2) for each litre of e