BS EN ISO 1119-2011 Geometrical product specifications (GPS) Series of conical tapers and taper angles《产品几何量技术规范 锥度和锥度角系列》.pdf

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN ISO 1119:2011Geometrical product specifications (GPS) Series of conical tapers and taper angles (ISO 1119:2011)Copyright European Committee for Standardization Provided by

2、IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN ISO 1119:2011 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN ISO 1119:2011. It supersedes BS EN ISO 1119:2002, which is withdrawn.The UK participa

3、tion in its preparation was entrusted to Technical Committee TDW/4, Technical Product Realization.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are respo

4、nsible for its correct application. BSI 2011 ISBN 978 0 580 69104 1 ICS 17.040.01 Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 January 2012.Amendments issu

5、ed since publicationDate Text affectedCopyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 1119 December 2011 ICS 17.040.01 Su

6、persedes EN ISO 1119:2002English Version Geometrical product specifications (GPS) - Series of conical tapers and taper angles (ISO 1119:2011) Spcification gomtrique des produits (GPS) - Srie dangles de cnes et de conicits (ISO 1119:2011) Geometrische Produktspezifikation (GPS) - Reihen von Regeln un

7、d Kegelwinkeln (ISO 1119:2011) This European Standard was approved by CEN on 14 December 2011. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-da

8、te lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation

9、 under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Fra

10、nce, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE F

11、R NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2011 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 1119:2011: ECopyright European Committee for Standardization Provided by IHS under license with CENNot for Resa

12、leNo reproduction or networking permitted without license from IHS-,-,-BS EN ISO 1119:2011 EN ISO 1119:2011 (E) 3 Foreword This document (EN ISO 1119:2011) has been prepared by Technical Committee ISO/TC 213 “Dimensional and geometrical product specifications and verification“ in collaboration with

13、Technical Committee CEN/TC 290 “Dimensional and geometrical product specification and verification” the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June

14、2012, and conflicting national standards shall be withdrawn at the latest by June 2012. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights

15、. This document supersedes EN ISO 1119:2002. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Franc

16、e, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of ISO 1119:2011 has been approved by CEN as a EN ISO 1119:20

17、11 without any modification. Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN ISO 1119:2011ISO 1119:2011(E) ISO 2011 All rights reserved iiiContents Page Foreword iv Introdu

18、ction . v 1 Scope 1 2 Normative references 1 3 Terms and definitions . 1 4 Values . 1 Annex A (informative) Relation to the GPS matrix model . 5 Bibliography 7 Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted

19、 without license from IHS-,-,-BS EN ISO 1119:2011ISO 1119:2011(E) iv ISO 2011 All rights reservedForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally car

20、ried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.

21、 ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare Interna

22、tional Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the

23、elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 1119 was prepared by Technical Committee ISO/TC 213, Dimensional and geometrical product specifications and verification. This third edition cancels and

24、 replaces the second edition (ISO 1119:1998); the tables have been corrected and updated, but not technically modified. Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN ISO

25、1119:2011ISO 1119:2011(E) ISO 2011 All rights reserved vIntroduction This International Standard is a geometrical product specification (GPS) standard and is to be regarded as a general GPS standard (see ISO/TR 14638). It influences chain links 1 and 2 of the chain of standards on angle. The ISO/GPS

26、 Masterplan given in ISO/TR 14638 gives an overview of the ISO/GPS system of which this document is a part. The fundamental rules of ISO/GPS given in ISO 8015 apply to this document and the default decision rules given in ISO 14253-1 apply to specifications made in accordance with this document, unl

27、ess otherwise indicated For more detailed information of the relation of this International Standard to other standards and the GPS matrix model, see Annex A. Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted

28、without license from IHS-,-,-BS EN ISO 1119:2011Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN ISO 1119:2011INTERNATIONAL STANDARD ISO 1119:2011(E) ISO 2011 All rights res

29、erved 1Geometrical product specifications (GPS) Series of conical tapers and taper angles 1 Scope This International Standard provides calculated values for a series of cones or conical tapers, ranging from 120 to less than 1, or ratios from 1:0,289 to 1:500, intended for general use in technical en

30、gineering. It applies only to plain conical surfaces, and excludes prismatic pieces, taper threads, bevel gears, etc. 2 Normative references The following referenced document is indispensable for the application of this document. For dated references, only the edition cited applies. For undated refe

31、rences, the latest edition of the referenced document (including any amendments) applies. ISO 3040, Geometrical product specifications (GPS) Dimensioning and tolerancing Cones 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 3040 apply. 4 Values Serie

32、s 1 and 2 initial values, as specified in Table 1, should be used in the order of preference given with the purpose of reducing the range of tools, gauges and measuring instruments required for production of conical parts. Table 2 shall be used only for the particular applications indicated in the l

33、ast column. For information, these tables give calculated values for the cone angle or the rate of taper, in order to facilitate design, production and control of conical pieces. Cones shall be dimensioned and toleranced according to ISO 3040. Copyright European Committee for Standardization Provide

34、d by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN ISO 1119:2011ISO 1119:2011(E) 2 ISO 2011 All rights reservedTable 1 Cones for general applications Nominal values Initial value Calculated values Cone angle, Rate of taper, C Serie

35、s 1 Series 2 Degrees, minutes and seconds “ Degrees Radians rad 120 2,094 395 10 1:0,288 675 1 90 1,570 796 33 1:0,500 000 0 75 1,308 996 94 1:0,651 612 7 60 1,047 197 55 1:0,866 025 4 45 0,785 398 16 1:1,207 106 8 30 0,523 598 78 1:1,866 025 4 1:3 18 55 28,719 9“ 18,924 644 42 0,330 297 35 1:4 14 1

36、5 0,117 7“ 14,250 032 70 0,248 709 99 1:5 11 25 16,270 6“ 11,421 186 27 0,199 337 30 1:6 9 31 38,220 2“ 9,527 283 38 0,166 282 46 1:7 8 10 16,440 8“ 8,171 233 56 0,142 614 93 1:8 7 9 9,607 5“ 7,152 668 75 0,124 837 62 1:10 5 43 29,317 6“ 5,724 810 45 0,099 916 79 1:12 4 46 18,797 0“ 4,771 888 06 0,0

37、83 285 16 1:15 3 49 5,897 5“ 3,818 304 87 0,066 641 99 1:20 2 51 51,092 5“ 2,864 192 37 0,049 989 59 1:30 1 54 34,857 0“ 1,909 682 51 0,033 330 25 1:50 1 8 45,158 6“ 1,145 877 40 0,019 999 33 1:100 34 22,630 9“ 0,572 953 02 0,009 999 92 1:200 17 11,321 9“ 0,286 478 30 0,004 999 99 1:500 6 52,529 5“

38、0,114 591 52 0,002 000 00 NOTE 1 For series 1, values from 120 to 1:3 are approximately in accordance with the R 10/2 series of preferred numbers, and values from 1:5 to 1:500 are in accordance with the R 10/3 series (see ISO 3). NOTE 2 The calculated values are for information only. Copyright Europ

39、ean Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN ISO 1119:2011ISO 1119:2011(E) ISO 2011 All rights reserved 3Table 2 Selection of cones for particular application Nominal values Internatio

40、nal Standard number Applications Initial value Calculated values Cone angle, Rate of taper, C Degrees, minutes and seconds “ Degrees Radians rad 7:24 16 35 39,444 3“ 16,594 290 08 0,289 625 00 1:3,428 571 4 ISO 297 Machine tool spindles, tool fits 1154 0,207 694 18 1:4,797 451 1 ISO 5237, ISO 8489-5

41、 Cones and tubes for textile industry 840 0,151 261 87 1:6,598 441 5 ISO 324 ISO 575 ISO 8489-3, ISO 8489-4, 7 0,122 173 05 1:8,174 927 7 ISO 8489-2 1:9 a6 41 34,776 9” 6,359 660 24 0,110 997 01 IEC 60095-2 Terminals of lead acid starter battery 1 : 9,98 5 44 10,550 0 5,736 263 88 0,100 116 69 ISO 1

42、2164-1 Hollow taper interface 1:12,262 4 40 12,151 4“ 4,670 042 05 0,081 507 61 ISO 239 Jacobs taper No. 2 1:12,972 4 24 52,903 9“ 4,414 695 52 0,077 050 97 ISO 239 Jacobs taper No. 1 1:15,748 3 38 13,442 9“ 3,637 067 47 0,063 478 80 ISO 239 Jacobs taper No. 33 6:100 3 26 12,177 6“ 3,436 716 00 0,05

43、9 982 01 1:16,666 666 7 ISO 594-1 ISO 595-1 ISO 595-2 Medical equipment 1:18,779 3 3 1,207 0“ 3,050 335 27 0,053 238 39 ISO 239 Jacobs taper No. 3 1:19,002 3 0 52,395 6“ 3,014 554 34 0,052 613 90 ISO 296 Morse taper No. 5 1:19,180 2 59 11,725 8“ 2,986 590 50 0,052 125 84 ISO 296 Morse taper No. 6 1:

44、19,212 2 58 53,825 5“ 2,981 618 20 0,052 039 05 ISO 296 Morse taper No. 0 1:19,254 2 58 30,421 7“ 2,975 117 13 0,051 925 59 ISO 296 Morse taper No. 4 1:19,264 2 58 24,864 4“ 2,973 573 43 0,051 898 65 ISO 239 Jacobs taper No. 6 1:19,922 2 52 31,446 3“ 2,875 401 76 0,050 185 23 ISO 296 Morse taper No.

45、 3 1:20,020 2 51 40,796 0“ 2,861 332 23 0,049 939 67 ISO 296 Morse taper No. 2 Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN ISO 1119:2011ISO 1119:2011(E) 4 ISO 2011 All

46、rights reservedTable 2 (continued) Nominal values International Standard number Applications Initial value Calculated values Cone angle, Rate of taper, C Degrees, minutes and seconds “ Degrees Radians rad 1:20,047 2 51 26,928 3“ 2,857 480 08 0,049 872 44 ISO 296 Morse taper No. 1 1:20,288 2 49 24,78

47、0 2“ 2,823 550 06 0,049 280 25 ISO 239 Jacobs taper No. 0 1:23,904 2 23 47,624 4“ 2,396 562 32 0,041 827 90 ISO 296 Brown & Sharpe taper No. 1 to 3 1:28 2 2 45,817 4“ 2,046 060 38 0,035 710 49 ISO 10651-4 Resuscitators 1:38 1 30 27,708 0“ 1,507 696 67 0,026 314 27 ISO 368 Cones and tubes for textile industry 1:36 1 35 29,209 6“ 1,591 447 11 0,027 775 99 ISO 5356-1 Anaesthetic equipment 1:40 1 25 56,351 6“ 1,432 319 89 0,024 998 70 1:64 0 53 42,822 0“ 0,895 228 34 0,015 624 68 ISO 368 Cones and tubes for textile industry aIn IEC 60095-2, the rate of taper is