BS EN ISO 1234-1998 Split pins《开口销》.pdf

1、BRITISH STANDARD BS EN ISO 1234:1998 Split pins The European Standard ENISO1234:1997 has the status of a British Standard ICS21.060.50BSEN ISO 1234:1998 This British Standard, having been prepared under the direction of the Engineering Sector Board, was published under the authority of the Standards

2、 Board and comes into effect on 15 May 1998 BSI 03-1999 ISBN 0 580 29088 3 National foreword This British Standard is the English language version of ENISO1234:1997. It is identical with ISO1234:1997. It supersedes BS7724:1994 which is declared obsolescent. The UK participation in its preparation wa

3、s entrusted by Technical Committee FME/9, Bolts, nuts and accessories, to Subcommittee FME/9/6, General puropse fasteners and accessories, which has the responsibility to: aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpret

4、ation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this Subcommittee can be obtained on request to its secretary. Cross-references Attention is drawn to the

5、fact that CEN and CENELEC Standards normally include an annex which lists normative references to international publications with their corresponding European publications. The British Standards which implement these international or European publications maybe found in the BSI Standards Catalogue u

6、nder the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct

7、 application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, theENISO title page, page 2, the ISO title page, page ii, pages 1 to 4 and aback cover. This stan

8、dard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Amendments issued since publication Amd. No. Date CommentsBSEN ISO 1234:1998 BSI 03-1999 i Contents Page National foreword Inside front cover

9、Foreword 2 Foreword ii Text of EN ISO 1234 1ii blankEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 1234 November 1997 ICS 21.060.50 Descriptors: See ISO document English version Split pins (ISO 1234:1997) Goupilles fendues (ISO1234:1997) Splinte (ISO1234:1997) This European Standard was ap

10、proved by CEN on 23 October 1997. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such natio

11、nal standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and not

12、ified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland

13、and United Kingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1997 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No.

14、 EN ISO 1234:1997 EENISO 1234:1997 BSI 03-1999 2 Foreword The text of the International Standard ISO1234:1997 has been prepared by Technical Committee ISO/TC 2 “Fasteners” in collaboration with Technical Committee CEN/TC 185 “Threaded and non-threaded mechanical fasteners and accessories”, the secre

15、tariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 1998, and conflicting national standards shall be withdrawn at the latest by May 1998. According to the CEN/CENE

16、LEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Swi

17、tzerland and the United Kingdom. Endorsement notice The text of the International Standard ISO1234:1997 was approved by CEN as a European Standard without any modification. Contents Page Foreword 2 1 Scope 1 2 Normative references 1 3 Dimensions 1 4 Requirements and reference International Standards

18、 4 5 Designation 4 Figure 1 1 Table 1 Dimensions 2 Table 2Nominal lengths l and commercial lengths 3 Table 3 Requirements and reference International Standards 4EN ISO 1234:1997 ii BSI 03-1999 Foreword ISO (the International Organization for Standardization) is a worldwide federation of national sta

19、ndards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International or

20、ganizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. Draft International Standards adopted by the technical committees are

21、 circulated to the member bodies for voting. Publication as an International Standard requires approval by at least75% of the member bodies casting a vote. International Standard ISO1234 was prepared by Technical Committee ISO/TC 2, Fasteners. This second edition cancels and replaces the first editi

22、on (ISO 1234:1976), which has been technically revised. Descriptors: Fasteners, steel products, pins (mechanics), split pins, specifications, characteristics, dimensions, designation.ENISO1234:1997 BSI 03-1999 1 1 Scope This International Standard specifies the characteristics of split pins. 2 Norma

23、tive references The following standards contain provisions which, through reference in this text, constitute provisions of this International Standard. At the time of publication, the editions indicated were valid. All standards are subject to revision, and parties to agreements based on this Intern

24、ational Standard are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below. Members of IEC and ISO maintain registers of currently valid International Standards. ISO 3269:1988, Fasteners Acceptance inspection. ISO 4042: 1) , Fasteners Electro

25、plated coatings. ISO 9717:1990, Phosphate conversion coatings for metals Method of specifying requirements. 3 Dimensions SeeFigure 1, Table 1 andTable 2. 1) To be published. (Revision of ISO4042:1989). Figure 1 ENISO 1234:1997 2 BSI 03-1999 Table 1 Dimensions (Lengths l: seeTable 2) Dimensions in mi

26、llimetres Nominal size a 0,6 0,8 1 1,2 1,6 2 2,5 3,2 d max. 0,5 0,7 0,9 1,0 1,4 1,8 2,3 2,9 min. 0,4 0,6 0,8 0,9 1,3 1,7 2,1 2,7 a max. 1,6 1,6 1,6 2,50 2,50 2,50 2,50 3,2 min. 0,8 0,8 0,8 1,25 1,25 1,25 1,25 1,6 b 2 2,4 3 3 3,2 4 5 6,4 c max. 1,0 1,4 1,8 2,0 2,8 3,6 4,6 5,8 min. 0,9 1,2 1,6 1,7 2,4

27、 3,2 4,0 5,1 Corresponding diameters b Bolts over 2,5 3,5 4,5 5,5 7 9 11 to 2,5 3,5 4,5 5,5 7 9 11 14 Clevis pins over 2 3 4 5 6 8 9 to 2 3 4 5 6 8 9 12 Nominal size a 4 5 6,3 8 10 13 16 20 d max. 3,7 4,6 5,9 7,5 9,5 12,4 15,4 19,3 min. 3,5 4,4 5,7 7,3 9,3 12,1 15,1 19,0 a max. 4 4 4 4 6,30 6,30 6,3

28、0 6,30 min. 2 2 2 2 3,15 3,15 3,15 3,15 b 8 10 12,6 16 20 26 32 40 c max. 7,4 9,2 11,8 15,0 19,0 24,8 30,8 38,5 min. 6,5 8,0 10,3 13,1 16,6 21,7 27,0 33,8 Corresponding diameters b Bolts over 14 20 27 39 56 80 120 170 to 20 27 39 56 80 120 170 Clevis pins over 12 17 23 29 44 69 110 160 to 17 23 29 4

29、4 69 110 160 a Nominal size = diameter of the split pin hole; for the pin hole diameter the following tolerance classes are recommended. H13 for nominal size # 1,2 H14 for nominal size 1,2 b For railway applications and in cases where split pins in clevis pins are subjected to alternating transverse

30、 forces, it is recommended to use the next larger split pin size to that specified in this table.ENISO1234:1997 BSI 03-1999 3 Table 2 Nominal lengths l and commercial lengths Dimensions in millimetres Length l Nominal size nom. min. max. 0,6 0,8 1 1,2 1,6 2 2,5 3,2 4 5 6,3 8 10 13 16 20 4 3,5 4,5 5

31、4,5 5,5 6 5,5 6,5 8 7,5 8,5 10 9,5 10,5 12 11 13 14 13 15 16 15 17 Range of 18 17 19 20 19 21 22 21 23 25 24 26 28 27 29 32 30,5 33,5 commercial 36 34,5 37,5 40 38,5 41,5 45 43,5 46,6 lengths 50 48,5 51,5 56 54,5 57,5 63 61,5 64,5 71 69,5 72,5 80 78,5 81,5 90 88 92 100 98 102 112 110 114 125 123 127

32、 140 138 142 160 158 162 180 178 182 200 198 202 224 222 226 250 248 252 280 278 282ENISO 1234:1997 4 BSI 03-1999 4 Requirements and reference International Standards SeeTable 3. Table 3 Requirements and reference International Standards 5 Designation A split pin of nominal size5mm, nominal lengthl=

33、50mm, made of steel (St) is designated as follows: Split pin ISO12345 50St Material Steel (St) Copper-zinc alloy (Cu Zn) Copper (Cu) Aluminium alloy (Al) Austenitic stainless steel (A) Other materials as agreed between customer and supplier. Ductility Each leg of the split pin shall be capable of wi

34、thstanding being bent back upon itself once, with no visible indication of fracture occuring at the point of bend. Surface finish Plain i.e.parts to be supplied in natural finish, treated with a protective lubricant, or with other coatings as agreed between customer and supplier. For electroplated c

35、oatings, see ISO4042. For phosphate coating see ISO 9717. Workmanship Pins shall be free of burrs, irregularities and detrimental defects. The eye shall be as circular as possible. The cross-section of the two straight legs together shall be circular. Acceptability For acceptance procedure, see ISO

36、3269.5 blankBS EN ISO 1234:1998 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.

37、 Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or

38、 ambiguity while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers

39、automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the

40、BSI implementation of those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI elect

41、ronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of s

42、tandards. For details of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the internationalstandardization bodies. Except as permitted un

43、der the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of impl

44、ementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.