BS EN ISO 1403-2008 Rubber hoses textile-reinforced for general-purpose water napplications - Specification《一般用途的输水用织物增强橡胶软管 规范》.pdf

1、BS EN ISO1403:2008ICS 23.040.70NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDRubber hoses, textile-reinforced, forgeneral-purposewater applications Specification (ISO1403:2005)This British Standardwas published under theauthority of the StandardsPolicy and Str

2、ategyCommittee on 31 December2008 BSI 2008ISBN 978 0 580 65734 4Amendments/corrigenda issued since publicationDate CommentsBS EN ISO 1403:2008National forewordThis British Standard is the UK implementation of EN ISO 1403:2008. Itis identical to ISO 1403:2005. It supersedes BS EN ISO 1403:1997 whichi

3、s withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee PRI/66, Rubber and plastics tubing, hoses and hoseassemblies.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the n

4、ecessary provisionsof a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunityfrom legal obligations.EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN ISO 1403November 2008ICS 23.040.70 Supersedes EN ISO 1403:1997 English VersionRubber h

5、oses, textile-reinforced, for general-purpose waterapplications - Specification (ISO 1403:2005)Tuyaux en caoutchouc armature textile dusage gnralpour leau - Spcifications (ISO 1403:2005)This European Standard was approved by CEN on 29 October 2008.CEN members are bound to comply with the CEN/CENELEC

6、 Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN

7、member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN membe

8、rs are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Swi

9、tzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2008 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN

10、 ISO 1403:2008: EBS EN ISO 1403:2008EN ISO 1403:2008 (E) 3 Foreword The text of ISO 1403:2005 has been prepared by Technical Committee ISO/TC 45 “Rubber and rubber products” of the International Organization for Standardization (ISO) and has been taken over as EN ISO 1403:2008 by Technical Committee

11、 CEN/TC 218 “Rubber and plastics hoses and hose assemblies” the secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2009, and conflicting national standards sh

12、all be withdrawn at the latest by May 2009. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN ISO 1403:1997.

13、 According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,

14、 Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of ISO 1403:2005 has been approved by CEN as a EN ISO 1403:2008 without any modification. BS EN ISO 1403:2008ISO 1

15、403:2005(E) ISO 2005 All rights reserved iiiContents Page Foreword iv 1 Scope 1 2 Normative references . 1 3 Terms and definitions. 2 4 Classification. 2 5 Materials and construction 2 6 Dimensions 2 6.1 Internal diameters and tolerances. 2 6.2 Concentricity . 2 6.3 Tolerance on length 2 6.4 Minimum

16、 thickness of lining and cover 2 7 Physical properties . 3 7.1 Rubber compounds 3 7.2 Finished hose 4 8 Marking. 4 BS EN ISO 1403:2008ISO 1403:2005(E) iv ISO 2005 All rights reservedForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodi

17、es (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations

18、, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the IS

19、O/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the

20、member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 1403 was prepared by Technical Committee ISO/TC 45, Rubber and rubb

21、er products, Subcommittee SC 1, Hoses (rubber and plastics). This fourth edition cancels and replaces the third edition (ISO 1403:1995), which has been technically revised. BS EN ISO 1403:2008INTERNATIONAL STANDARD ISO 1403:2005(E) ISO 2005 All rights reserved 1Rubber hoses, textile-reinforced, for

22、general-purpose water applications Specification WARNING Persons using this International Standard should be familiar with normal laboratory practice. This standard does not purport to address all the safety problems, if any, associated with its use. It is the responsibility of the user to establish

23、 appropriate health and safety practices and to ensure compliance with any national regulatory conditions. 1 Scope This International Standard specifies the requirements for three types of general-purpose textile-reinforced rubber water hose with an operating temperature range of 25 C to +70 C and a

24、 maximum working pressure of up to 25 bar 1). These hoses are not intended to be used for conveyance of potable (drinking) water, for washing-machine inlets, as firefighting hoses, for special agricultural machines or as collapsible water hoses. These hoses may be used with additives which lower the

25、 freezing point of water. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.

26、ISO 37, Rubber, vulcanized or thermoplastic Determination of tensile stress-strain properties ISO 188:1998, Rubber, vulcanized or thermoplastic Accelerated ageing and heat resistance tests ISO 1307, Rubber and plastics hoses for general-purpose industrial applications Bore diameters and tolerances,

27、and tolerances on length ISO 1402, Rubber and plastics hoses and hose assemblies Hydrostatic testing ISO 1746:1998, Rubber or plastics hoses and tubing Bending tests ISO 4671, Rubber and plastics hoses and hose assemblies Methods of measurement of dimensions ISO 4672:1997, Rubber and plastics hoses

28、Sub-ambient temperature flexibility tests ISO 7326:1991, Rubber and plastics hoses Assessment of ozone resistance under static conditions ISO 8033, Rubber and plastics hoses Determination of adhesion between components ISO 8330, Rubber and plastics hoses and hose assemblies Vocabulary 1) 1 bar = 0,1

29、 MPa BS EN ISO 1403:2008ISO 1403:2005(E) 2 ISO 2005 All rights reserved3 Terms and definitions For the purposes of this document, the terms and definitions in ISO 8330 apply. 4 Classification Hoses are designated as one of the following types depending on their pressure rating: Type 1: Low pressure

30、Designed for a maximum working pressure of 6 bar. Type 2: Medium pressure Designed for a maximum working pressure of 10 bar. Type 3: High pressure Designed for a maximum working pressure of 25 bar. 5 Materials and construction The hose shall consist of: a rubber lining; a reinforcement of natural or

31、 synthetic textile, applied by any suitable technique; a rubber cover. The lining and cover shall be of uniform thickness, concentric to comply with the minimum thickness specified, and free from holes, porosity and other defects. The cover finish may be smooth, fluted or fabric-marked. 6 Dimensions

32、 6.1 Internal diameters and tolerances When measured in accordance with ISO 4671, the internal diameters and their tolerances shall conform to the values specified in Table 1. 6.2 Concentricity When determined in accordance with ISO 4671, the concentricity, based on a total indicator reading between

33、 the internal diameter and the outside surface of the cover, shall be no greater than 1,0 mm for hoses of internal diameter up to and including 76 mm, and no greater than 1,5 mm for hoses of inside diameter greater than 76 mm. 6.3 Tolerance on length When measured in accordance with ISO 4671, the to

34、lerance on cut lengths shall be as specified in ISO 1307. 6.4 Minimum thickness of lining and cover When measured in accordance with ISO 4671, the minimum thickness of the lining plus cover shall be 1,5 mm. If the cover is fluted, the depth of the flutes shall not be greater than 50 % of the cover t

35、hickness. BS EN ISO 1403:2008ISO 1403:2005(E) ISO 2005 All rights reserved 3Table 1 Internal diameters and tolerances Internal diameter mm Tolerance mm 10 0,75 12,5 0,75 16 0,75 19 0,75 25 1,25 32 1,25 38 1,50 50 1,50 63 1,50 76 1,50 100 2,00 7 Physical properties 7.1 Rubber compounds When measured

36、by the methods listed in Table 2, the physical properties of the compounds used for the lining and cover shall conform to the values specified in Table 2. Tests shall be carried out either on samples taken from the hose or from separately vulcanized sheets 2 mm in thickness and vulcanized to the sam

37、e cure state as production hoses. Table 2 Physical properties of rubber compounds Requirements Property Lining Cover Test method Minimum tensile strength 5,0 MPa (types 1 and 2) 7,0 MPa (type 3) 5,0 MPa (types 1 and 2) 7,0 MPa (type 3) ISO 37 (dumb-bell test piece) Minimum elongation at break 200 %

38、200 % ISO 37 (dumb-bell test piece) Resistance to ageing: Change in tensile strength from original value (max.) Change in elongation at break from original value (max.) 25 % 50 % 25 % 50 % ISO 188:1998 (3 days at 100 C 1 C), air-oven method;ISO 37 (dumb-bell test piece) BS EN ISO 1403:2008ISO 1403:2

39、005(E) 4 ISO 2005 All rights reserved7.2 Finished hose When measured by the methods listed in Table 3, the physical properties of finished hoses shall conform to the values specified in Table 3. Table 3 Physical properties of finished hoses Property Requirements Test method Proof pressure at 23 C 9

40、bar (type 1) 15 bar (type 2) 50 bar (type 3) ISO 1402 Change in length at proof pressure 7 % ISO 1402 Minimum burst pressure 18 bar (type 1) 30 bar (type 2) 100 bar (type 3) ISO 1402 Adhesion between components 1,5 kN/m (min.) ISO 8033 Ozone resistance No cracking observed under 2 magnification ISO

41、7326:1991, method 1 up to 25 mm ID method 2 or 3 for other sizes Flexibility at 23 C T/D not less than 0,8 ISO 1746:1998, method A Low-temperature flexibility No cracks shall be detected and the hose shall pass the proof test specified above. ISO 4672:1997, method B, at 25 C 2 C 8 Marking The hose s

42、hall be continuously and durably marked with the following minimum information: a) the manufacturers name or identification; b) the number and year of publication of this International Standard; c) the hose type number; d) the internal diameter, in millimetres; e) the maximum working pressure, in ba

43、rs; f) the quarter and year of manufacture. EXAMPLE MAN/ISO 1403:2005/Type 2/25/10 bar/1Q05 BS EN ISO 1403:2008BS EN ISO1403:2008BSI GroupHeadquarters 389Chiswick High Road,London, W4 4AL, UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 - British Standards InstitutionBSI is the independent national bod

44、y responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at theinternational level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest ame

45、ndments oreditions.It is the constant aim of BSI to improve the quality of our products and services.We would be grateful if anyone finding an inaccuracy or ambiguity while usingthis British Standard would inform the Secretary of the technical committeeresponsible, the identity of which can be found

46、 on the inside front cover. Tel:+44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensuresthat subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards pub

47、lications should beaddressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 89967001 Email: You may also buy directly using a debit/creditcard from the BSI Shop on the Website http:/ response to orders for international standards, it is BSI policy to supply theBSI implementation of

48、those that have been published as British Standards,unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European andinternational standards through its Library and its Technical Help to ExportersService. Various BSI electronic information services

49、 are also available whichgive details on all its products and services. Contact Information Centre. Tel:+44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048 Email: Subscribing members of BSI are kept up to date with standards developmentsand receive substantial discounts on the purchase price of standards. For detailsof these and other benefits contact Membership Administrati