BS EN ISO 1479-2011 Hexagon head tapping screws《六角头自攻螺钉》.pdf

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN ISO 1479:2011Hexagon head tapping screws(ISO 1479:2011)BS EN ISO 1479:2011 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN ISO 1479:20

2、11.It supersedes BS EN ISO 1479:1995 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee FME/9/3, Fasteners - Product Standards.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purpor

3、t to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. BSI 2011ISBN 978 0 580 68771 6ICS 21.060.10Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards

4、 Policy and Strategy Committee on 31 August 2011.Amendments issued since publicationDate Text affectedEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 1479 August 2011 ICS 21.060.10 Supersedes EN ISO 1479:1994English Version Hexagon head tapping screws (ISO 1479:2011) Vis tle tte hexagonale

5、(ISO 1479:2011) Sechskant-Blechschrauben (ISO 1479:2011) This European Standard was approved by CEN on 1 July 2011. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any

6、 alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other languag

7、e made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark,

8、Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION

9、EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2011 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 1479:2011: EBS EN ISO 1479:2011EN ISO 1479:2011 (E) 3 Foreword This document (EN ISO 1479:

10、2011) has been prepared by Technical Committee ISO/TC 2 “Fasteners“ in collaboration with Technical Committee CEN/TC 185 “Fasteners” the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endo

11、rsement, at the latest by February 2012, and conflicting national standards shall be withdrawn at the latest by February 2012. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for id

12、entifying any or all such patent rights. This document supersedes EN ISO 1479:1994. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Rep

13、ublic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of ISO 1479:2011 has b

14、een approved by CEN as a EN ISO 1479:2011 without any modification. BS EN ISO 1479:2011ISO 1479:2011(E) ISO 2011 All rights reserved iiiForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing

15、International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaiso

16、n with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of tec

17、hnical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is dra

18、wn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 1479 was prepared by Technical Committee ISO/TC 2, Fasteners, Subcommittee SC 13, Fasteners with non-metric threa

19、d. This second edition cancels and replaces the first edition (ISO 1479:1983), which has been technically revised. BS EN ISO 1479:2011BS EN ISO 1479:2011INTERNATIONAL STANDARD ISO 1479:2011(E) ISO 2011 All rights reserved 1Hexagon head tapping screws 1 Scope This International Standard specifies the

20、 characteristics of hexagon head tapping screws with thread sizes from ST 2,2 to ST 9,5 inclusive. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the lates

21、t edition of the referenced document (including any amendments) applies. ISO 225, Fasteners Bolts, screws, studs and nuts Symbols and descriptions of dimensions ISO 1478, Tapping screws thread ISO 2702, Heat-treated steel tapping screws Mechanical properties ISO 3269, Fasteners Acceptance inspection

22、 ISO 3506-4, Mechanical properties of corrosion-resistant stainless steel fasteners Part 4: Tapping screws ISO 4042, Fasteners Electroplated coatings ISO 4759-1, Tolerances for fasteners Part 1: Bolts, screws, studs and nuts Product grades A, B and C ISO 8992, Fasteners General requirements for bolt

23、s, screws, studs and nuts ISO 10683, Fasteners Non-electrolytically applied zinc flake coatings ISO 16048, Passivation of corrosion-resistant stainless-steel fasteners BS EN ISO 1479:2011ISO 1479:2011(E) 2 ISO 2011 All rights reserved3 Dimensions See Figure 1 and Table 1. Symbols and descriptions of

24、 dimensions are specified in ISO 225. a) Type C b) Type F c) Type R aShape of indentation is optional. bDimension a is to be measured at the core diameter of the first full thread. Figure 1 Hexagon head tapping screw BS EN ISO 1479:2011ISO 1479:2011(E) ISO 2011 All rights reserved 3Table 1 Dimension

25、s Dimensions in millimetres Thread size ST 2,2 ST 2,9 ST 3,5 ST 4,2 ST 4,8 ST 5,5 ST 6,3 ST 8 ST9,5Pa0,8 1,1 1,3 1,4 1,6 1,8 1,8 2,1 2,1 a max. 0,8 1,1 1,3 1,4 1,6 1,8 1,8 2,1 2,1 damax. 2,8 3,5 4,1 4,9 5,5 6,3 7,1 9,2 10,7 max. 3,20 5,00 5,50 7,00 8,00 8,00 10,00 13,00 16,00 s min. 3,02 4,82 5,32 6

26、,78 7,78 7,78 9,78 12,73 15,73 e min. 3,38 5,40 5,96 7,59 8,71 8,71 10,95 14,26 17,62 max. 1,6 2,3 2,6 3,0 3,8 4,1 4,7 6,0 7,5 k min. 1,3 2,0 2,3 2,6 3,3 3,6 4,1 5,2 6,5 kwmin. 0,9 1,4 1,6 1,8 2,3 2,5 2,9 3,6 4,5 r min. 0,10 0,10 0,10 0,20 0,20 0,25 0,25 0,40 0,40 Type C 2,0 2,6 3,2 3,7 4,3 5,0 6,0

27、7,5 8,0 Type F 1,6 2,1 2,5 2,8 3,2 3,6 3,6 4,2 4,2 y ref. Type R 2,7 3,2 3,6 4,3 5,0 6,3 lbType C and Type R Type F nom. min. max. min. max. 4,5 3,7 5,3 3,7 4,5 6,5 5,7 7,3 5,7 6,5 9,5 8,7 10,3 8,7 9,5 13 12,2 13,8 12,2 13,0 Range 16 15,2 16,8 15,2 16,0 of 19 18,2 19,8 18,2 19,0 preferred 22 21,2 22

28、,8 20,7 22,0 lengths 25 24,2 25,8 23,7 25,0 32 30,7 33,3 30,7 32,0 38 36,7 39,3 36,7 38,0 45 43,7 46,3 43,5 45,0 50 48,7 51,3 48,5 50,0 aP = pitch of the thread. bSizes with lengths marked with a dash () cannot be manufactured. BS EN ISO 1479:2011ISO 1479:2011(E) 4 ISO 2011 All rights reserved4 Spec

29、ifications and reference International Standards See Table 2. Table 2 Specifications and reference International Standards Material Steel, in accordance with ISO 2702 Stainless steel General requirements ISO 8992 Thread ISO 1478 Steel grade/ hardness class A2-20H, A4-20H, A5-20H Mechanical propertyI

30、nternational StandardISO 2702 ISO 3506-4 Product grade A Tolerances International Standard ISO 4759-1 As processed Finish Coating Requirements for electroplating are specified in ISO 4042. Requirements for non-electrolytically applied zinc flake coatings are specified in ISO 10683. Additional requir

31、ements or other finishes or coatings shall be agreed between the supplier and the purchaser. Requirements for passivation are specified in ISO 16048. Acceptability Acceptance inspection is specified in ISO 3269. 5 Designation EXAMPLE 1 A hexagon head tapping screw with thread size ST 3,5, nominal le

32、ngth l = 16 mm made of steel (St) in accordance with ISO 2702 and rounded end (Type R) is designated as follows: Tapping screw ISO 1479 - ST 3,5 16 - St - R EXAMPLE 2 A hexagon head tapping screw with thread size ST 3,5, nominal length l = 16 mm made of stainless steel (A4-20H) in accordance with IS

33、O 3506-4 and rounded end (Type R) is designated as follows: Tapping screw ISO 1479 - ST 3,5 16 - A4-20H - R BS EN ISO 1479:2011This page deliberately left blankThis page deliberately left blankBSI is the independent national body responsible for preparing British Standardsand other standards-related

34、 publications, information and services. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.British Standards Institution (BSI)raising standards worldwideBSI Group Headquarters389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 90

35、01Fax +44 (0)20 8996 Standards are updated by amendment or revision. Users of British Stan-dards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and serv-ices. We would be grateful if anyone finding an inaccur

36、acy or ambiguity whileusing this British Standard would inform the Secretary of the technical com-mittee responsible, the identity of which can be found on the inside frontcover.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001BSI offers Members an individual updating service called PLUS which ensur

37、esthat subscribers automatically receive the latest editions of standards.Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001Email: Buying standardsYou may buy PDF and hard copy versions of standards directly using acredit card from the BSI Shop on the website addition all orders for BSI, internation

38、al and foreign standards publicationscan be addressed to BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001Email: In response to orders for international standards, it is BSI policy tosupply the BSI implementation of those that have been publishedas British Standards, unless oth

39、erwise requested.Information on standardsBSI provides a wide range of information on national, Europeanand international standards through its Knowledge Centre.Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005Email: Various BSI electronic information services are also available whichgive details on

40、all its products and services. Tel: +44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048Email: BSI Subscribing Members are kept up to date with standardsdevelopments and receive substantial discounts on the purchase priceof standards. For details of these and other benefits contact Membership Ad-ministratio

41、n. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards via BritishStandards Online can be found at information about BSI is available on the BSI website at www.bsi- subsists in all BSI publications. BSI also holds the copyright,in the U

42、K, of the publications of the international standardization bodies. Ex-cept as permitted under the Copyright, Designs and Patents Act 1988 no ex-tract may be reproduced, stored in a retrieval system or transmitted in anyform or by any means electronic, photocopying, recording or otherwise without pr

43、ior written permission from BSI. This does not preclude the freeuse, in the course of implementing the standard of necessary details such assymbols, and size, type or grade designations. If these details are to be usedfor any other purpose than implementation then the prior written permissionof BSI must be obtained. Details and advice can be obtained from the Copy-right & Licensing Manager.Tel: +44 (0)20 8996 7070Email: