BS EN ISO 1927-7-2012 Monolithic (unshaped) refractory products Tests on pre-formed shapes《整体(粗制)耐火材料产品 预制件测定》.pdf

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationMonolithic (unshaped) refractory productsPart 7: Tests on pre-formed shapesBS EN ISO 1927-7:2012Copyright European Committee for Standardization Provided by IHS under license wit

2、h CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-National forewordThis British Standard is the UK implementation of EN ISO 1927-7:2012. It supersedes BS EN 1402-7:2003, which is withdrawn.The UK participation in its preparation was entrusted to Technical Commit

3、teeRPI/1, Refractory products and materials.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standa

4、rds Institution 2013.Published by BSI Standards Limited 2013.ISBN 978 0 580 65762 7 ICS 81.080Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 January 2013.Ame

5、ndments issued since publicationAmd. No. Date Text affectedBRITISH STANDARDBS EN ISO 1927-7:2012Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-EUROPEAN STANDARD NORME EUROPENNE

6、EUROPISCHE NORM EN ISO 1927-7 December 2012 ICS 81.080 Supersedes EN 1402-7:2003English Version Monolithic (unshaped) refractory products - Part 7: Tests on pre-formed shapes (ISO 1927-7:2012) Produits rfractaires monolithiques (non faonns) - Partie 7: Essais sur pices pr-formes (ISO 1927-7:2012) Un

7、geformte (monolithische) feuerfeste Erzeugnisse - Teil 7: Prfungen an Fertigteilen (ISO 1927-7:2012) This European Standard was approved by CEN on 30 November 2012. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Stand

8、ard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English

9、, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bul

10、garia, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, T

11、urkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. E

12、N ISO 1927-7:2012: EBS EN ISO 1927-7:2012Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-EN ISO 1927-7:2012 (E) 2 Contents Page Foreword . 3 BS EN ISO 1927-7:2012Copyright Europe

13、an Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-EN ISO 1927-7:2012 (E) 3 Foreword This document (EN ISO 1927-7:2012) has been prepared by Technical Committee ISO/TC 33 “Refractories“ in collabor

14、ation with Technical Committee CEN/TC 187 “Refractory products and materials” the secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2013, and conflicting na

15、tional standards shall be withdrawn at the latest by June 2013. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersed

16、es EN 1402-7:2003. According to the CEN/CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Mac

17、edonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. Endorsement notice The text of ISO 1927-7:2012 has been approved by

18、CEN as a EN ISO 1927-7:2012 without any modification. BS EN ISO 1927-7:2012Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-ISO 1927-7:2012(E) ISO 2012 All rights reserved iiiCont

19、ents Page1 Scope . 12 Normative references 13 Terms and definitions . 14 Principle 45 Apparatus . 46 Inspection by attributes 66.1 Preparation of the test piece . 66.2 Measurement of dimensions . 66.3 Measurement of angles 66.4 Measurement of warpage 76.5 Measurement of corner defects 86.6 Measureme

20、nt of edge defects . 96.7 Measurement of craters and bubbles . 106.8 Measurement of cracks . 116.9 Measurement of protrusions and indentations .116.10 Measurement of fins 126.11 Segregations . 126.12 Friability 127 Inspection by variables .127.1 Destructive test methods 127.2 Non-destructive test me

21、thods 148 Test report 19Bibliography .21BS EN ISO 1927-7:2012Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-INTERNATIONAL STANDARD ISO 1927-7:2012(E)Monolithic (unshaped) refrac

22、tory products Part 7: Tests on pre-formed shapes1 ScopeThis part of ISO 1927 specifies methods for the testing of as-delivered pre-formed shapes. It applies to shapes fabricated from dense and insulating castables and ramming materials as defined in ISO 1927-1.NOTE Acceptance values for the individu

23、al test methods described should be agreed between the parties involved.2 Normative referencesThe following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced

24、document (including any amendments) applies.ISO 1927-1, Monolithic (unshaped) refractory products Part 1 Introduction and classificationISO 1927-6, Monolithic (unshaped) refractory products Part 6: Measurement of physical properties3 Terms and definitionsFor the purposes of this document, the follow

25、ing terms and definitions apply.3.1corner defectmissing corner, defined by the three dimensions a, b and c as indicated in Figure 1 ISO 2012 All rights reserved 1BS EN ISO 1927-7:2012Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction

26、or networking permitted without license from IHS-,-,-ISO 1927-7:2012(E)cbaKeya, b and c Three dimensions defining the missing cornerFigure 1 Typical corner defect3.2edge defectmissing edge, defined by the three dimensions, e, f, and g as indicated in Figure 2 gefKeye, f, and g Three dimensions defin

27、ing the missing edgeFigure 2 Typical edge defect3.3craterclearly defined hole in the surface of a shape whose parameters, i.e. maximum diameter, minimum diameter and depth, can be measuredNOTE Its origin can be a bubble produced during manufacture.2 ISO 2012 All rights reservedBS EN ISO 1927-7:2012C

28、opyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-ISO 1927-7:2012(E)3.4hairline cracksfine cracks visible on the surface of a shape whose length can be measured and whose width is l

29、ess than or equal to 0,2 mm, see Figure 3 123Key1 Hairline crack2 Surface crazing3 Open cracksFigure 3 Typical cracks3.5surface crazingnetwork of hairline cracks confined to the surface of the shape, see Figure 33.6open crackscracks or tears on the surface whose length is more than 10 mm and whose w

30、idth is more than 0,2 mm See Figure 3.3.7protrusions and indentationsimperfections that can occur during fabrication or firing, if applicable3.8finsthin layer of material on the face of a shape that projects beyond the edge3.9segregationseparation of aggregate and fines during fabrication to leave a

31、 honeycomb appearance and/or a layer of excess fines3.10friabilitycrumbly texture due to poor consolidation and/or mould leakage3.11warpagedeviation of a plane surface from being flat ISO 2012 All rights reserved 3BS EN ISO 1927-7:2012Copyright European Committee for Standardization Provided by IHS

32、under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-ISO 1927-7:2012(E)4 PrincipleTesting of pre-formed shapes by qualitative and/or quantitative methods. These methods are of two types:a) Inspection by attributes by evaluating the integrity of a r

33、efractory shape by visual inspection of cracks or other surface defects and by conformance to dimensional tolerances;b) Inspection by variables by evaluating the quality of a refractory shape by determining physical properties using appropriate destructive or non-destructive test methods.NOTE It is

34、not obligatory to use all the test methods described in this part of ISO 1927 when determining the quality of a pre-formed shape.5 Apparatus5.1 Linear measuring devices, steel tape and/or callipers in accordance with the tolerance required and conforming to an accuracy that is twice the intended acc

35、uracy of the measurement.NOTE Where possible, linear tolerances less than 1 mm should be measured with callipers. Steel tape measurements are accurate to the millimetre (0,5 mm can be estimated) whereas callipers are accurate to 0,1 mm.5.2 Steel straightedge, at least 5 mm thick and of sufficient le

36、ngth to span the diagonal of the largest shape to be measured.5.3 Two steel measuring wedges, which shall be either:a) type 1, at least 50 mm in length and 10 mm in thickness at one end, of uniform cross-section for a length of at least 10 mm from that end and then tapering to zero thickness at the

37、other end (see for example Figure 4a), orb) type 2, up to 160 mm in length with an even taper from 4 mm to zero (see for example Figure 4b).Each wedge shall be graduated and numbered along the slope to show the thickness of the wedge between the base and the slope in increments of either 0,5 mm (typ

38、e 1) or 0,1 mm (type 2).Dimensions in millimetres108642501010a) Type 14 ISO 2012 All rights reservedBS EN ISO 1927-7:2012Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-ISO 1927-

39、7:2012(E)40383634323028262422201816141210864 2 10 354160b) Type 2Figure 4 Two types of measuring wedge5.4 Graticule, with 0,1 mm graduations and/or feeler gauges of an appropriate size and accuracy to be used for the measurement of crack width. If necessary, the gauges can be replaced by measuring w

40、edges of appropriate accuracy.5.5 Sliding bevel, for the measurement of angles.5.6 Depth gauge calibrated in millimetres of depth, having a probe of 3 mm diameter.5.7 Breakage defect sizer, with a slot uncovering 2 mm on both surfaces, for determination of minimum defect sizes for corner and edge de

41、fects, according to Figure 5.NOTE 1 One breakage defect sizer can be used together with a steel straightedge for the measurement of corner defects (see 6.5). Two breakage defect sizers can be used together with a linear measuring device for the measurement of edge defects (see 6.6).NOTE 2 A breakage

42、 defect sizer permits an objective definition of the point of departure for the measurement of the size of a broken edge.Dimensions in millimetres3303010030322Figure 5 Breakage defect sizer ISO 2012 All rights reserved 5BS EN ISO 1927-7:2012Copyright European Committee for Standardization Provided b

43、y IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-ISO 1927-7:2012(E)5.8 Balance, capable of measuring to an accuracy of 1 %.5.9 Ultrasonic pulse velocity measuring equipment.5.10 Equipment for determining the resonant frequency by mechanic

44、al shock.5.11 Rebound hammer.5.12 Drying oven, capable of being controlled at 110 C 5 C.5.13 Furnace, capable of operating at 1 050 C 25 C.6 Inspection by attributes6.1 Preparation of the test pieceThe definition of edges may be improved, after any protrusions or indentations have been measured, by

45、removing any projections such as fins or protrusions. This can normally be achieved by light abrasion.6.2 Measurement of dimensionsLinear dimensions shall be measured by means of a linear measuring device (see 5.1), and unless otherwise agreed, shall be measured to the nearest 0,5 mm.6.3 Measurement

46、 of anglesAngles shall be measured by adjusting the sliding bevel to fit the shape (see Figure 6) and the angle determined by the use of a protractor (see Figure 7).Figure 6 Positioning the sliding bevel6 ISO 2012 All rights reservedBS EN ISO 1927-7:2012Copyright European Committee for Standardizati

47、on Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-ISO 1927-7:2012(E)Figure 7 Measurement of the angle6.4 Measurement of warpageFor a concave surface, place the straightedge on edge across a diagonal of the surface being tested

48、, insert a wedge at the point of maximum warpage (ensuring that the reading is not affected by raised imperfections on the castable surface) and record the maximum obtainable reading to the nearest 0,5 mm at the point of contact between the wedge and the straightedge.For a convex surface, insert a wedge at each end of the straightedge and perpendicular to it as shown in Figure 8. Adjust the wedges, to a position not more than 15 mm from the corner of the shap