1、BRITISH STANDARD BS EN ISO 2162-2:1996 BS 308-1.18: 1996 Technical product documentation Springs Part 2: Presentation of data cylindrical helical compression springs The European Standard EN ISO 2162-2:1996 has the status of a British Standard ICS 01.100.20; 21.160BSEN ISO 2162-2:1996 This British S
2、tandard, having been prepared under the directionof the Engineering SectorBoard, was published underthe authority of the Standards Board and comes into effect on 15 November 1996 BSI 10-1998 The following BSI references relate to the work on this standard: Committee reference TDE/4 Draft announced i
3、n BSI News ISBN 0 580 26332 0 Committees responsible for this British Standard The preparation of this British Standard was entrusted to Technical Committee TDE/4, Engineering drawing practice, upon which the following bodies were represented: Atomic Weapons Establishment British Gas plc British Sta
4、ndards Society Drawing Office Material Manufacturers and Dealers Association Electricity Association Gauge and Tools Makers Association HEVAC Association Institution of Chemical Engineers Institution of Engineering Designers Power Generation Contractors Association Society of British Aerospace Compa
5、nies Ltd. University of Warwick Amendments issued since publication Amd. No. Date CommentsBSEN ISO 2162-2:1996 BSI 10-1998 i Contents Page Committees responsible Inside front cover National foreword ii Foreword 2 1 Scope 3 2 Normative references 3 3 Definitions 3 4 Letter symbols 3 5 Presentation of
6、 data 3 Annex A (informative) Example of the presentation of a preprinted data set for a spring 6 Annex B (informative) Bibliography 8 Annex ZA (normative) Normative references to international publications with their relevant European publications 9 Table 1 Spring design parameters and letter symbo
7、ls 4 Table 2 Types of spring ends 5 List of references Inside back coverBSEN ISO 2162-2:1996 ii BSI 10-1998 National foreword This British Standard has been prepared by Technical Committee TDE/4 and is the English language version of EN ISO 2162-2:1996 Technical product documentation Springs Part 2:
8、 Presentation of data for cylindrical helical compression springs, published by the European Committee for Standardization (CEN). It is identical with ISO 2162-2:1993 published by the International Organization for Standardization (ISO). It is envisaged that when the full range of European Standards
9、 on technical drawing is implemented BS 308 will be withdrawn. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity fr
10、om legal obligations. Cross-references Publication referred to Corresponding British Standard BS EN ISO 2162 Technical product documentation EN ISO 2162-1:1996 Springs (ISO 2162-1:1993) BS EN ISO 2162-1:1996 Simplified representation EN ISO 2162-3:1996 BS EN ISO 2162-3:1996 Vocabulary (ISO 2162-3:19
11、93) Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, theEN title page, pages 2 to 10, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amend
12、ment table on theinside front cover.EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 2162-2 July 1996 ICS 01.100.20; 21.160 Descriptors: Drawings, technical drawings, springs, helical springs, technical data sheets English version Technical product documentation Springs Part 2: Presentation
13、of data for cylindrical helical compression springs (ISO 2162-2:1993) Documentation technique de produits Ressorts Partie 2: Prsentation des donnes techniques des ressorts cylindriques de compression (ISO 2162-2:1993) Technische Produktdokumentation Federn Teil 2: Angaben fr zylindrische Schraubendr
14、uckfedern (ISO 2162-2:1993) This European Standard was approved by CEN on 1996-03-02. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists
15、and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsi
16、bility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, P
17、ortugal, Spain, Sweden, Switzerland and United Kingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1996 Copyright reserved to CEN members Ref. No. EN ISO 2162-2:1996 EENISO 2162-2:1
18、996 2 BSI 10-1998 Foreword The text of the International Standard from Technical Committee ISO/TC 10, Technical drawings, product definition and related documentation, of the International Organization for Standardization (ISO) has been taken over as a European Standard by the Technical Board of CEN
19、. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by January1997, and conflicting national standards shall be withdrawn at the latest by January1997. According to the CEN/CENELEC Internal Regulations
20、, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. NOTENor
21、mative references to International Standards are listed in annex ZA (normative).EN ISO 2162-2:1996 BSI 10-1998 3 1 Scope This part of ISO 2162 establishes a uniform system for the presentation of technical data and for the representation of cylindrical helical compression springs to be used in techn
22、ical product documentation intended for e.g. tender and/or order drawings. 2 Normative references The following standards contain provisions which through reference in this text, constitute provisions of this part of ISO 2162. At the time of publication, the editions indicated were valid. All standa
23、rds are subject to revision and parties to agreements based on this part of ISO 2162 are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below. Members of IEC and ISO maintain registers of currently valid International Standards. ISO 2162-1:1
24、993, Technical product documentation Springs Part 1: Simplified representation. ISO 2162-3:1993, Technical product documentation Springs Part 3: Vocabulary. 3 Definitions For the purposes of this part of ISO 2162, the definitions given in ISO 2162-3 apply. 4 Letter symbols See Table 1. 5 Presentatio
25、n of data 5.1 General The data presented shall comprise a) graphical representation, information on action and on the type of finish to ends; and b) design and manufacturing data. 5.2 Representation, data on the spring action and indication of the type of spring ends Graphical representation of the
26、spring shall be in accordance with ISO 2162-1. Data on the spring action shall be indicated preferably by means of a load deflection chart (or graph) showing the predominant requirements necessary for the functioning of the spring together with any additional requirements. The type of spring ends sh
27、all be indicated in accordance with Table 2. 5.3 Technical data list The technical data list presented shall include all information necessary for the manufacture of the springs. Possibilities for the adaptation of a certain spring to given requirements during manufacture shall be specified. In part
28、icular, for springs working on a rod the minimum inside diameter of the coil shall be stated, and for springs working in a cylinder the maximum outside diameter of the coil shall be stated. To aid economy in manufacture, tolerances on sizes should not be unnecessarily restrictive. An example of a pr
29、eprinted data list is given in annex A. This form provides a uniform scheme for the presentation and indication of data on helical compression springs, regardless of the method of data entry. It should be used for enquiries, offers and orders for this type of spring.ENISO 2162-2:1996 4 BSI 10-1998 T
30、able 1 Spring design parameters and letter symbols No. Parameter Unit Letter symbol (Formula) 1 outside (external) diameter of spring mm D e 2 enlargement of outside diameter of spring when loaded mm DD e 3 inside diameter of spring mm D i 4 mean diameter of coil mm 5 diameter of wire (or bar) mm d
31、6 maximum outside diameter of wire (or bar) mm d max 7 modulus of elasticity (or Young modulus) N/mm 2or MPa E 8.1 load cycle frequency Hz or s 1 f 8.2 natural frequency (both ends fixed) Hz or s 1 f e 9 spring load for the spring lengths L 1 , L 2 , L 3 , ., L n(atambient temperature of 20 C) N F 1
32、 , F 2 , F 3 , ., F n 10 spring load for the minimum test length L n N F n 11 theoretical spring load at solid length L c N F cth 12 spring load at temperatures other than 20 C, e.g.spring load F 2at 0 C N F 2/0 13 modulus of rigidity N/mm 2or MPa G 14 stress correction factor depending on D/d k 15
33、free length mm L 0 16 spring length for the loads F 1 , F 2 , F 3 , ., F n mm L 1 , L 2 , L 3 , ., L n 17 minimum acceptable test length for F n mm L n 18 solid length mm L c 19 active coils n 20 total number of coils n t 21 static axial spring rate N/mm R s 22 static transverse spring rate N/mm R t
34、r 23 lateral deflection force at defined axial force N jC 24 deflection of spring (stroke) between two loads mm s h 25 torsion stress for F 1 , F 2 , F 3 , ., F n N/mm 2 t 1 , t 2 , ., t n 26 torsion stress for L c N/mm 2 t c 27 torsion stress range (corrected) for F 1 , F 2 , F 3 , ., F n N/mm 2 t
35、k1 , t k2 , , t kn 28 torsion stress (corrected) for a given stroke s h N/mm 2 t kh 29 working temperature (minimum/maximum) C T 30 static axial flexibility (N/mm 1 ) 1/R s 31 static transverse flexibility (N/mm 1 ) 1/R t 32 working or test duration (during relaxation tests) h t 33 (required) total
36、number of cycles up to rupture N 34 permissible relaxation at defined initial stress (normally t 2 ), temperature and duration N/mm 2 dF D D e D i + 2 - = EN ISO 2162-2:1996 BSI 10-1998 5 Table 2 Types of spring ends Form Execution View A open, not ground B closed, not ground C open, ground D closed
37、, ground E closed, pigtail ends F closed and bend to the centre NOTEThe views show a right-hand (RH) spring. However, the same types of ends apply equally for left-hand (LH) springs.ENISO 2162-2:1996 6 BSI 10-1998 Annex A (informative) Example of the presentation of a preprinted data set for a sprin
38、g NOTE 1The actual size of data sheets is A4, in accordance with ISO 5457. A.1 Front side, or page 1 Title block (see ISO 7200)EN ISO 2162-2:1996 BSI 10-1998 7 A.2 Overleaf, or page 2ENISO 2162-2:1996 8 BSI 10-1998 Annex B (informative) Bibliography 1 ISO 5457:1980, Technical drawings Sizes and layo
39、ut of drawing sheets. 2 ISO 7200:1984, Technical drawings Title blocks.EN ISO 2162-2:1996 BSI 10-1998 9 Annex ZA(normative) Normative references to international publications with their relevant European publications This European Standard incorporates by dated or undated reference, provisions from
40、other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment
41、 or revision. For undated references the latest edition of the publication referred to applies. Publication Year Title EN Year ISO 2162-1 1993 Technical product documentation Springs Part 1: Simplified representation EN ISO 2162-1 1996 ISO 2162-3 1993 Technical product documentation Springs Part 3:
42、Vocabulary EN ISO 2162-3 199610 blankBS EN ISO 2162-2:1996 BSI 10-1998 List of references See national foreword.BSI 389 Chiswick High Road London W4 4AL | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
43、 | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level
44、. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be gra
45、teful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating serv
46、ice called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. In response to orders for int
47、ernational standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its
48、Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments
49、and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieva
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1