BS EN ISO 2338-1998 Parallel pins of unhardened steel and austenitic stainless steel《未淬硬钢和奥氏体不锈钢制的平行销》.pdf

1、BRITISH STANDARD BS EN ISO 2338:1998 Parallel pins of unhardened steel and austenitic stainless steel The European Standard EN ISO 2338:1997 has the status of a British Standard ICS 21.060.50BSENISO2338:1998 This British Standard, having been prepared under the directionof the Engineering SectorBoar

2、d, was published underthe authority of the Standards Board and comes into effect on 15May1998 BSI 03-1999 ISBN 0 580 29089 1 National foreword This British Standard is the English language version of EN ISO2338:1997. It is identical with ISO2338:1997. It supersedes BSEN22338:1992 which is withdrawn.

3、 The UK participation in its preparation was entrusted by Technical Committee FME/9, Bolts, nuts and accessories, to Subcommittee FME/9/6, General puropse fasteners and accessories, which has the responsibility to: aid enquirers to understand the text; present to the responsible international/Europe

4、an committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this subcommittee can be obtained on request to its secretary.

5、Cross-references Attention is drawn to the fact that CEN and CENELEC Standards normally include an annex which lists normative references to international publications with their corresponding European publications. The British Standards which implement these international or European publications m

6、ay be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British

7、 Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, theEN ISO title page, page 2, the ISO title page, pag

8、e ii, pages 1 to 3 andaback cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Amendments issued since publication Amd. No. Date CommentsBSENISO2338:1998 BSI 03-1999 i Contents

9、Page National foreword Inside front cover Foreword 2 Foreword ii Text of EN ISO 2338 1ii blankEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 2338 November 1997 ICS 21.060.50 Supersedes EN 22338:1992 Descriptors: See ISO document English version Parallel pins, of unhardened steel and austen

10、itic stainless steel (ISO2338:1997) Goupilles cylindriques en acier non tremp et en acier inoxydable austnitique (ISO2338:1997) Zylinderstifte aus ungehrtetem Stahl und austenitischem nichtrostendem Stahl (ISO2338:1997) This European Standard was approved by CEN on 23 October 1997. CEN members are b

11、ound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the

12、 Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same statu

13、s as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CEN European Committee for Stan

14、dardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1997 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 2338:1997 EENISO2338:1997 BSI 03-1999 2 For

15、eword The text of the International Standard ISO2338:1997 has been prepared by Technical Committee ISO/TC2 “Fasteners” in collaboration with Technical Committee CEN/TC185 “Threaded and non-threaded mechanical fasteners and accessories”, the secretariat of which is held by DIN. This European Standard

16、 supersedes EN22338:1992. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May1998, and conflicting national standards shall be withdrawn at the latest by May1998. According to the CEN/CENELEC Inte

17、rnal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland

18、 and the United Kingdom. Endorsement notice The text of the International Standard ISO2338:1997 was approved by CEN as a European Standard without any modification. Contents Foreword 2 1 Scope 1 2 Normative references 1 3 Dimensions 1 4 Requirements and reference International Standards 3 5 Designat

19、ion 3 Figure 1 1 Table 1 Dimensions 2 Table 2 Requirements and reference International Standards 3ENISO2338:1997 ii BSI 03-1999 Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing Internat

20、ional Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with I

21、SO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an In

22、ternational Standard requires approval by at least75% of the member bodies casting a vote. International Standard ISO2338 was prepared by Technical Committee ISO/TC2, Fasteners. This second edition cancels and replaces the first edition (ISO2338:1986), which has been technically revised. Descriptors

23、: Fasteners, steel products, pins (mechanics), straight pins, specifications, characteristics, dimensions, designation.ENISO2338:1997 BSI 03-1999 1 1 Scope This International Standard specifies the characteristics of parallel pins of unhardened steel and austenitic stainless steel, with nominal diam

24、eters d from0,6mm to50mm inclusive. 2 Normative references The following standards contain provisions which, through reference in this text, constitute provisions of this International Standard. At the time of publication, the editions indicated were valid. All standards are subject to revision, and

25、 parties to agreements based on this International Standard are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below. Members of IEC and ISO maintain registers of currently valid International Standards. ISO 3269:1988, Fasteners Acceptance i

26、nspection. ISO 3506-1:1997, Mechanical properties of corrosion-resistant stainless steel fasteners Part1: Bolts, screws and studs. ISO 4042: 1) , Fasteners Electroplated coatings. ISO 9717:1990, Phosphate conversion coatings for metals Method of specifying requirements. 3 Dimensions See Figure 1 and

27、Table 1. 1) To be published. (Revision of ISO4042:1989) Figure 1 ENISO2338:1997 2 BSI 03-1999 Table 1 Dimensions Dimensions in millimetres d m6/h8 a 0,6 0,8 1 1,2 1,5 2 2,5 3 4 5 6 8 10 12 16 20 25 30 40 50 c = 0,12 0,16 0,2 0,25 0,3 0,35 0,4 0,5 0,63 0,8 1,2 1,6 2 2, 5 3 3, 5 4 5 6, 3 8 l b nom. mi

28、n. max. 2 1,75 2,25 3 2,75 3,25 4 3,75 4,25 5 4,75 5,25 6 5,75 6,25 8 7,75 8,25 10 9,75 10,25 12 11,5 12,5 Range 14 13,5 14,5 16 15,5 16,5 18 17,5 18,5 20 19,5 20,5 22 21,5 22,5 24 23,5 24,5 of 26 25,5 26,5 28 27,5 28,5 30 29,5 30,5 32 31,5 32,5 35 34,5 35,5 40 39,5 40,5 commercial 45 44,5 45,5 50 4

29、9,5 50,5 55 54,25 55,75 60 59,25 60,75 65 64,25 65,75 70 69,25 70,75 lengths 75 74,25 75,75 80 79,25 80,75 85 84,25 85,75 90 89,25 90,75 95 94,25 95,75 100 99,25 100,75 120 119,25 120,75 140 139,25 140,75 160 159,25 160,75 180 179,25 180,75 200 199,25 200,75 a Other tolerances as agreed between cust

30、omer and supplier. b For nominal lengths above 200 mm, steps of 20 mm.ENISO2338:1997 BSI 03-1999 3 4 Requirements and reference International Standards SeeTable 2. Table 2 Requirements and reference International Standards 5 Designation EXAMPLE 1 An unhardened steel parallel pin, with nominal diamet

31、er d=6mm, tolerance classm6 and nominal length l=30mm is designated as follows: Parallel pin ISO23386m6 30St EXAMPLE 2 An unhardened austenitic stainless steel pin of gradeA1, with nominal diameterd=6mm, tolerance classm6 and nominal length l=30mm is designated as follows: Parallel pin ISO23386m6 30

32、A1 Material a Steel (St) Austenitic stainless steel Hardness 125 HV30 to 245 HV30 A1 in accordance with ISO 3506-1, hardness 210 HV30 to 280 HV30 Plain, i.e. pins to be supplied in natural finish treated with a protective lubricant, unless otherwise specified by agreement between customer and suppli

33、er. Surface finish Preferred coatings are black oxide, phosphate coating or zinc plating with chromate conversion coating (see ISO9717 and ISO4042). Plain, i.e. pins to be supplied in natural finish. Other coatings as agreed between customer and supplier. All tolerances shall apply prior to the appl

34、ication of a plating or coating. Surface roughness For pins with tolerance class m6: R ak 0,8 4m For pins with tolerance class h8: R ak 1,6 4m Workmanship Pins shall be free of irregularities or detrimental defects. No burrs shall appear on any part of the pin. Acceptability The acceptance procedure

35、 is covered in ISO 3269. a Other materials as agreed between customer and supplier.BS EN ISO 2338:1998 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Euro

36、pe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our product

37、s and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an

38、individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response

39、 to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its

40、 Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards de

41、velopments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publicat

42、ions of the internationalstandardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permissi

43、on from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.