BS EN ISO 3501-2015 Plastics piping systems Mechanical joints between fittings and pressure pipes Test method for resistance to pull-out under constant longitudinal force《塑料管系统 配件和.pdf

1、BSI Standards PublicationBS EN ISO 3501:2015Plastics piping systems Mechanical joints betweenfittings and pressure pipes Test method for resistanceto pull-out under constantlongitudinal forceBS EN ISO 3501:2015 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN ISO

2、 3501:2015.It supersedes BS EN 712:1995 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee PRI/88/4, Test Methods - Plastic Piping.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not pu

3、rport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2015.Published by BSI Standards Limited 2015ISBN 978 0 580 81802 8ICS 23.040.60Compliance with a British Standard cannot confer immunity fromlegal obligatio

4、ns.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 31 March 2015.Amendments issued since publicationDate T e x t a f f e c t e dEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 3501 March 2015 ICS 23.040.60 Supersedes EN 712:1993Englis

5、h Version Plastics piping systems - Mechanical joints between fittings and pressure pipes - Test method for resistance to pull-out under constant longitudinal force (ISO 3501:2015) Systmes de canalisations en plastique - Assemblages mcaniques entre raccords et tubes sous pression - Mthode dessai de

6、rsistance larrachement sous une force longitudinale constante (ISO 3501:2015) Kunststoff-Rohrleitungssysteme - Mechanische Verbindungen zwischen Fittings und Druckrohren - Prfverfahren fr den Widerstand gegen Zugbelastung bei konstanter Zugkraft (Ausreiprfung) (ISO 3501:2015) This European Standard

7、was approved by CEN on 7 February 2015. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such

8、 national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own

9、language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Gr

10、eece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUN

11、G CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2015 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 3501:2015 EBS EN ISO 3501:2015EN ISO 3501:2015 (E) 3 Foreword This document (EN ISO 3501:2015) has been pre

12、pared by Technical Committee ISO/TC 138 “Plastics pipes, fittings and valves for the transport of fluids“ in collaboration with Technical Committee CEN/TC 155 “Plastics piping systems and ducting systems” the secretariat of which is held by NEN. This European Standard shall be given the status of a

13、national standard, either by publication of an identical text or by endorsement, at the latest by September 2015, and conflicting national standards shall be withdrawn at the latest by September 2015. Attention is drawn to the possibility that some of the elements of this document may be the subject

14、 of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 712:1993. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this Euro

15、pean Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slo

16、venia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. Endorsement notice The text of ISO 3501:2015 has been approved by CEN as EN ISO 3501:2015 without any modification. BS EN ISO 3501:2015ISO 3501:2015(E)Contents PageForeword iv1 Scope . 12 Normative references 13 Principle 14 Test para

17、meters and requirements 15 Apparatus . 26 Test pieces . 27 Procedure. 38 Test report . 3Annex A (normative) Test parameters . 4 ISO 2015 All rights reserved iiiBS EN ISO 3501:2015ISO 3501:2015(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national st

18、andards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International o

19、rganizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for i

20、ts further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/d

21、irectives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in

22、the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the meaning of ISO specific terms and expressions rela

23、ted to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword Supplementary information.The committee responsible for this document is ISO/TC 138, Plastics pipes, fittings and valves for the tr

24、ansport of fluids, Subcommittee SC 5, General properties of pipes, fittings and valves of plastic materials and their accessories Test methods and basic specifications .This second edition cancels and replaces the first edition (ISO 3501:1976), which has been technically revised. The reason for modi

25、fication is for applicability to other plastics materials, other sizes and/or other test conditions and alignment with texts of other standards on test methods. This edition of ISO 3501 is prepared under the Vienna Agreement, so that the content is also aligned with EN 712:1994, which will be replac

26、ed.The modifications are: no material is mentioned; test parameters are omitted, although the original test parameters can be found in Annex A; the diameter limit is removed; no requirements are given; editorial changes have been introduced.iv ISO 2015 All rights reservedBS EN ISO 3501:2015Plastics

27、piping systems Mechanical joints between fittings and pressure pipes Test method for resistance to pull-out under constant longitudinal forceWARNING Persons using this document should be familiar with normal laboratory practice, if applicable. The use of this International Standard can involve hazar

28、dous materials, operations, and equipment. This International Standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this International Standard to establish appropriate safety and health practices and determine the a

29、pplicability of regulatory limitations prior to use.1 ScopeThis International Standard specifies a method for checking the ability of assembled uniaxial joints between fittings and plastic pressure pipes to withstand longitudinal tensile stresses. The test applies regardless of the design and materi

30、al of the fitting used for jointing plastics pipe.This test method is not applicable to fusion-welded joints.2 Normative referencesThe following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the editi

31、on cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 3126, Plastics piping systems Plastics components Determination of dimensionsISO 17456:2006, Plastics piping systems Multilayer pipes Determination of long-term strength3 Pr

32、incipleAn assembled joint is subjected to a longitudinal tensile force calculated as a function of the pipe dimensions and the maximum permissible induced hoop stress of the relevant pipe.4 Test parameters and requirementsThe test parameters of the standard which refers to this International Standar

33、d shall be used and the requirements shall be fulfilled. If one or more parameters are not given in the referring International Standard, the ones given in Annex A shall apply.The following test parameters should be given by the standard which refers to this International Standard:a) pull-out force

34、(N);b) test duration (h);c) test temperature (C);d) free length (mm).INTERNATIONAL STANDARD ISO 3501:2015(E) ISO 2015 All rights reserved 1BS EN ISO 3501:2015ISO 3501:2015(E)5 ApparatusTensile loading equipment, capable of applying a constant tensile force, with a tolerance of 2 %, along the longitu

35、dinal axis of the pipe(s) connected to the mechanical fitting being tested.The tensile force can be applied directly or via a lever arm, using dead weights or a fluid-activated loading cylinder. The test framework, as illustrated in Figure 1, shall be designed to permit the transmission of the appli

36、ed force to the joint and fitting assembly without reduction by frictional losses generated by the supporting structure.Faa123l0l0Key1 end load bearing type A end cap2 fitting to be tested3 end load bearing type A end capF applied longitudinal end load forcel0pipe free lengtha end load reaction forc

37、es generated within the loading frameworkFigure 1 Typical apparatusThe test temperature shall be maintained at 2 C of the specified temperature.6 Test piecesThe test specimen shall consist of one or more joints formed by the assembly of at least one fitting and one or more pieces of plastic pressure

38、 pipe of the size and quality for which the fitting is designed.2 ISO 2015 All rights reservedBS EN ISO 3501:2015ISO 3501:2015(E)The fittings and pipes shall not be tested until 24 h after their production. For practical reasons, the manufacturer can wait a shorter time before testing. In case of di

39、spute, a duration of 24 h shall apply.The assembly of the joint should be carried out in accordance with the manufacturers instructions.7 ProcedureDetermine the mean wall thickness of the pipe, according to ISO 3126. Secure the test specimen in the apparatus. Apply the calculated force gradually ove

40、r a period of 30 s. Hold the specimen in constant tension for the specified test period.Inspect the joint(s) for, and record any, indications of loosening of the joint or partial or complete separation from the fitting by pull-out.8 Test reportThe test report shall include the following information:

41、a) a reference to this International Standard (i.e. ISO 3501:2014) and to the referring standard;b) the nominal pressure class or S series of the components e.g. fitting(s), pipe comprising the joint(s) under test;c) all details necessary for identification of the test pieces, including the nominal

42、size of the pipes and fittings used to produce the test pieces, the type of material, and the manufacturers code;d) the test period;e) the test temperature;f) the calculated force;g) the free length (l0);h) information on the loosening of the joint or partial or complete separation of the joint by p

43、ull-out including the pressure at which a leakage occurred (if any);i) any factors which might have affected the results, such as any incidents or any operating details not specified in this International Standard;j) the date of test. ISO 2015 All rights reserved 3BS EN ISO 3501:2015ISO 3501:2015(E)

44、Annex A (normative) Test parametersA.1 GeneralThe test parameters in Table A.1 shall be used, if applicable.Table A.1 Test parametersTest duration hTest temperature C1 23The free length (l0) of each pipe shall be at least three times the nominal outside diameter (dn), with a minimum of 250 mm.If, fo

45、r pipes with dngreater than 315 mm, the specified minimum free length cannot be achieved, a shorter free length can be chosen with a minimum of two times dn, unless otherwise specified in the referring standard or specification. If a climate chamber is needed and the minimum free length cannot be ac

46、hieved, a shorter free length l0of at least 150 mm can be used.For solid wall pipes, the force (FT) shall be calculated by using Clause A.2. Co-extruded pipes are considered to be solid wall pipes.For multilayer pipes, the force (FT) shall be calculated by using Clause A.3.A.2 Solid wall pipeFrom th

47、e dimensions of the solid wall pipe, calculate the cross-section of the pipe wall, and from this figure, calculate the force (FT) necessary to produce a longitudinal stress of one and a half times the maximum permissible working stress of the material from which the pipe is made, using Formula (1).F

48、edeTTmnm= ()15, pi (1)whereTis the applicable test stress given in the referring standard (MPa);emis the mean wall thickness of the pipe (mm);dnis the nominal outside diameter of the pipe (mm).4 ISO 2015 All rights reservedBS EN ISO 3501:2015ISO 3501:2015(E)A.3 Multilayer pipeUsing the dimensions of

49、 the multilayer pipe, calculate the force (FT) using Formula (2).FpdeTTnm=()15202, pi(2)wherepTis the calculated pressure and is half of the value of the pressure (bar) at 1 h at 20 C;This can be calculated by:a) using the formula from ISO 17456:2006, Annex A, if the long-term pressure strength is calculated with Procedure I: “Calculation method” (multilayer P pipes);b) from reference curve from ISO 17456:2006, if the long-term pressure strength is deter-mined with Procedure II: “Pressure test” (mult