1、STD.BS1 BS EN IS0 4bL3-L-ENGL 3999 RI 3b24bb9 0793559 722 BRITISH STANDARD Plastics - Ethylenelvinyl acetate (ENAC) moulding and extrusion materials - Part 1: Designation and specification The European Sandard EN IS0 46131: 1999 has the status of a British Standard ICs 83.080.20 BS EN IS0 4613-k1999
2、 NO COPYING WITHOUT ES1 PERMISSION EXCEPT AS PERMITTED BY COPYRIGBr LAW STD.BSI BS EN IS0 4633-1-ENGL 1999 W 1624669 0793560 444 0 been prepared under the direction of the Sector Amd. No. Date Committee for Materials and Chemicals, was published under the authority of the Standards Committee and com
3、es into effect on 15 September 1999 O BSI 09-1999 ISBN O 580 32994 1 BS EN IS0 4613-11999 Comments National foreword This British Standard is the English language version of EN IS0 46131: 1999. It is identical with IS0 4613-1:1993. The UK participation in its preparation was entrusted to Technical C
4、ommittee PRU82, Thermoplastic materials, which has the responsibility to: - aid enquirers to understand the text; - present to the responsible internationaLEuropean committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed - monitor related internatio
5、nal and European developments and proinuigate them in the UK A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references Attention is drawn to the fact that CEN and CENELEC Standards nomially include an annex which lists normative references to
6、 international publications with their corresponding European publications. The British Standards which implement these international or European publications may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find
7、facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal ob
8、ligations. Summary of pages This document comprises a front cover, an inside front cover, the EN IS0 title page, the EN IS0 foreword page, the IS0 title page, page ii, pages 1 to 7, the annex ZA page, an inside back cover and a back cover. The BSI copyright notice displayed throughout tkis document
9、indicates when the document was last issued. H STD-BSI BS EN IS0 4bL3-L-ENGL 1999 II Lb24bb9 07915bL 380 I EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN IS046134 May 1999 ICs 83.080.20 English version Plastics - Ethylene/vinyl acetate (ENAC) moulding and extrusion materials - Part 1: Designat
10、ion and specification (IS0 4613- 1 : 1 993) Plastiques - Mathriaux base de copolymre hylndactate de vinyle (ENAC) pour moulage et extrusion - Partie 1: Dsignation et spcification (IS0 4613- 1 : 1 993) Kunststoffe - Ethylen-Vinylacetat (WAC) Formmassen - Teil 1 : Bezeichnungssystem und Basis fr Spezi
11、fikationen (IS0 461 3-1 :1993) This European Standard was approved by CEN on 16 April 1999. GEN members are bound to comply with the CENICENELEC Intemal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-todate li
12、sts and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the resp
13、onsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Ne
14、therlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMI1TEE FOR STANDARDIZATION COMITE EUROPEEN DE NORMALISATION EUROPISCHES KOMITEE FUR NORMUNG Central Secretariat: rue de Stassart, 36 8-1050 Brussels O 1999 GEN All rights of exploitation in any form and by any me
15、ans reserved worldwide for CEN national Members. Ref. No. EN IS0 4613-1:1999 E STD-BSI BS EN IS0 4bL3-3-ENGL 3999 3624669 0793562 217 m EN IS0 4613-11999 Foreword The text of the International Standard from Technical Committee ISOEC 61 “Plastics“ of the International Organization for Standardization
16、 (ISO) has been taken over as an European Standard by Technical Committee CENiTC 249 “Plastics“, the secretariat of which is held by IBN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by November 1
17、999, and conflicting national standards shall be withdrawn at the latest by November 1999. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finl
18、and, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of the International Standard IS0 4613-1:1993 has been approved by CEN as a European Standard without any modification. NOT
19、E: Normative references to International Standards are listed in annex ZA (normative). STD-BSI BS EN IS0 4633-1-ENGL 3999 1111 1624669 07915b3 153 EN IS0 4613-1:1999 I NT ER NAT I O NA L STA N DAR D IS0 4613-1 Second edition 1993-1 0-01 Plastics - Ethylene/vinyl acetate (E/VAC) moulding and extrusio
20、n materials - Part 1: Designation and specification Plastiques - Matriaux base de copolyrnre thylnelacrate de vinyle (ElVAC) pour moulage et extrusion - Partie 1: Dsignation et spcification Reference number IS0 4613-1 :1993(E) STD.BSI BS EN IS0 4613-1-ENGL 1999 II 1624669 0791564 09T 111 EN IS0 4613
21、-li1999 Foreword IS0 (the International Organization for Standardization) is a worldwide federation of national standards bodies (IS0 member bodies). The work of preparing International Standards is normally carried out through IS0 technical committees. Each member body interested in a subject for w
22、hich a technical committee has been established has the right to be represented on that committee. International organizations. governmental and non-governmental, in liaison with ISO, also take part in the work. IS0 colla borates closely with the International Electrotechnical Commission (IEC) on al
23、l matters of electrotechnical standardization. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. International Standard IS0
24、 461 3-1 was prepared by Technical Committee ISO/TC 61, Plastics, Sub-Committee SC 9, Thermoplastic materials. . This second edition cancels and replaces the first edition (IS0 4613-1:1985), which has been brought into accordance with the re- vised frame text for designation standards. IS0 4613 cons
25、ists of the following parts, under the general title Plastics - Ethylenelvinyl acetate (1 VAC) moulding and extrusion materi- SIS: - Part 1: Designation and specification - Part 2: Preparation of test specimens and determination of proper- ties Descriptors: plastics, thermoplastic resins, moulding m
26、aterials, extrusion materials, vinyl acetate copolymers, designation. data blocks. i STD-BSI BS EN IS0 4bL3-L-ENGL 2999 111 Lb24bb9 079L5b5 T26 m EN IS0 4613-1:1999 Plastics - Ethylenelvinyl acetate (EIVAC) moulding and extrusion materials - Part I: Designation and specif icatisn 1 Scope 1.1 This pa
27、rt of IS0 4613 establishes a system of designation for ethylenelvinyl acetate thermoplastic material, which may be used as the basis for specifications. 1.2 The types of E/VAC plastics are differentiated from each other by a classification system based on appro- priate levels of the designatory prop
28、erties a) vinyl acetate content b) melt flow rate and on information about intended application and/or method of processing, important properties, additives, colorants, fillers and reinforcing materials. 1.3 This part of IS0 4613 is applicable to all ethylene vinyl acetate copolymers containing from
29、 3 % (dm) to 50 % (dm) (approximately 25 % molar) of vinyl acetate. It applies to materials ready for normal use in the form of powder, granules or pellets and to materials unmodified or modified by colorants, additives, fillers, etc. 1.4 It is not intended to imply that materials having the same de
30、signation give necessarily the same perform- ance. This part of IS0 4613 does not provide engineering data, performance data or data on processing conditions which may be required to specify a material for a particular application and/or method of processing, If such additional properties are requir
31、ed, they shall be determined in accordance with the test methods specified in IS0 4613-2, if suitable. 1.5 additional requirements may be given in data block 5 (see clause 3, introductotv paragraph). In order to specify a thermoplastic material for a particular application or to ensure reproducible
32、processing, 1 STD*BSI BS EN IS0 4b13-1-ENGL 1799 lb2tbbY 077LShb 7b2 I EN IS0 4613-1:1999 Description block (OptOnal) 2 Normative references Identity block Individual-item block Data Data Data Data Data block block block block block 1 2 3 4 5 in tern at ion ai Number block Standard The following sta
33、ndards contain provisions which, through reference in this text, constitute provisions of this part of IS0 4613. At the time of publication, the editions indicated were valid. All standards are subject to revision, and parties to agreements based on this part of IS0 461 3 are encouraged to investiga
34、te the possibility of applying the most recent editions of the standards indicated below. Members of IEC and IS0 maintain registers of currently valid International Standards. IS0 1043-1 :1987, Plastics - Symbols - Part 1: Basic polymers and their special characteristics. IS0 11 33: 1991, Plastics -
35、 Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate IMVR) of thermoplastics. IS0 461 3-2: 1989, Plastics - Ethy/ene/vinyl acetate copolymer (/VACI thermoplastics - Part 2: Preparation of test specimens and determination of properties. IS0 8985:1989, Plastics - Ethylene/viny
36、l acetate copolymer (/VACI thermoplastics - Determination of vinyl acetate content. 3 Designation and specification system The designation and specification system for thermoplastics is based on the following standardized pattern: The designation consists of an optional description block, reading “T
37、hermoplastics“, and an identity block com- prising the International Standard number and an individual-item block. For unambiguous coding, the individual-item block is subdivided into 5 data blocks comprising the following information: - Data block 1: - Data block 2: Identification of the plastic by
38、 its symbol E/VAC in accordance with IS0 1043-1 and in- formation about the polymerization process or composition of the polymer (see 3.1). Position 1: intended application or method of processing (see 3.2). Positions 2 to 8: Important properties, additives and supplementary information (see 3.2). -
39、 Data block 3: - Data block 4: - Data block 5: Designatory properties (see 3.3). Fillers or reinforcing materials and their nominal content (see 3.4). For the purpose of specifications, a fifth data block may be added containing additional information. The first character of the individual-item bloc
40、k shall be a hyphen. The data blocks shall be separated from each other by commas. If a data block is not used, this shall be indicated by doubling the separation sign, .e. by two commas (,I. 2 STD-BSI BS EN IS0 Yb13-3-ENGL 3999 ea Lb2Ybb9 0793567 BT9 PIp EN IS0 4613-1:1999 3.1 Data block 1 In this
41、data block, after the hyphen, E/VAC plastics are identified by the symbol “E/VAC“. in accordance with IS0 1043-1 and, after a space, the vinyl acetate content is indicated. The vinyl acetate content, expressed as a percentage by mass, shall be determined in accordance with IS0 8985. The possible val
42、ues of vinyl acetate content are divided into 7 ranges, each represented by a 2-figure code-number as specified in table 1. 3.2 Data block 2 In this data block, information about intended application and/or method of processing is given in position 1 and information about important properties, addit
43、ives and colour in positions 2 to 8. The code-letters used are specified in table2. If information is presented in positions 2 to 8 and no specific information is given in position 1, the letter X shall be inserted in position 1. 3.3 Data block 3 In this data block, the range of the melt flow rate i
44、s represented by a letter and a 3-figure code-number (see 3.3.1). If a property value falls on or near a range limit, the manufacturer shall state which range will designate the ma- terial. If subsequent individual test values lie on, or on either side of, the limit because of manufacturing toleranc
45、es, the designation is not affected. NOTE 1 polymers. Not all the combinations of the values of the designatory properties have to be provided for currently available 3.3.1 Melt flow rate The melt mass-flow rate shall be determined in accordance with IS0 1133 under the test conditions specified in t
46、able3. Table 1 - Code-numbers used for additional information in data block 1 Codenumber WAC content % dm) 03 08 13 18 25 35 45 z 3 but Q 5 5 but G 10 10 but Q 15 15 but c 20 20 but c 30 30 but Q 40 40 but g 50 3 STD.BS1 BS EN IS0 4633-3-ENGL 1999 3624669 0773568 735 RI Adhesives EN IS0 4613-1:1999
47、A Processing stabilized Table 2 - Code-letters used in data block 2 I Code-letter 1 Position 1 I Code-letter I Positions 2 to 8 I Calendering h- C , Coloured E F I I B I Blow moulding I B I Antibiocking D Powder Extrusion E Expandable Extrusion of films F Special burning characteristics I C a P impa
48、ct modified Compression moulding Y Z I I G I Generaluse 1 G 1 Granules - increased electrical conductivity Antistatic I 1 H I Coating I H I Heat ageing stabilized Code-letter D B 2 I I K I Cable and wire coating 1 K I Metal deactivated Temperature Nominal load C kg 190 2.16 1 50 2.16 125 0,325 I L I
49、 Monofilament extrusion I L I Light or weather stabilized I I . M I Moulding I I I I 1 N I Natural (no colour added) I I Rotational moulding R Mould release agent I I I I s I Sintering I S I Lubricated I I T 1 Tape manufacture I T I Transparent I I W I Stabilized against hydrolysis I I Nindicat ion I I I I I 1 I 4 STD.BSI BS EN IS0 4b33-L-ENGL L999 i1624669 O793569 671 S EN IS0 4613-1:1999 Set of conditions B is used only for materials having an MfR greater than i00 when tested under set of conditions D. Set of condi
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1