BS EN ISO 4796-1-2016 Laboratory glassware Bottles Screw-neck bottles《实验室玻璃器皿 瓶 螺纹颈口瓶》.pdf

1、BSI Standards PublicationBS EN ISO 4796-1:2016Laboratory glassware BottlesPart 1: Screw-neck bottlesBS EN ISO 4796-1:2016 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN ISO4796-1:2016. It supersedes BS EN ISO 4796-1:2001 which iswithdrawn.The UK participation i

2、n its preparation was entrusted to TechnicalCommittee LBI/1/2, Laboratory Equipment.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its c

3、orrectapplication. The British Standards Institution 2016.Published by BSI Standards Limited 2016ISBN 978 0 580 83097 6ICS 71.040.20; 81.040.30Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of the Standards Poli

4、cy and Strategy Committee on 29 February 2016.Amendments/corrigenda issued since publicationDate T e x t a f f e c t e dEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 4796-1 February 2016 ICS 71.040.20 Supersedes EN ISO 4796-1:2000English Version Laboratory glassware - Bottles - Part 1: Sc

5、rew-neck bottles (ISO 4796-1:2016) Verrerie de laboratoire - Flacons - Partie 1: Flacons col vis (ISO 4796-1:2016) Laborgerte aus Glas - Flaschen - Teil 1: Flaschen mit Gewindehals (ISO 4796-1:2016) This European Standard was approved by CEN on 13 December 2015. CEN members are bound to comply with

6、the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Managem

7、ent Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same statu

8、s as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,

9、 Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey andUnited Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2016 CEN Al

10、l rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 4796-1:2016 EBS EN ISO 4796-1:2016EN ISO 4796-1:2016 (E) 3 European foreword This document (EN ISO 4796-1:2016) has been prepared by Technical Committee ISO/TC 48 “Laboratory equipment“

11、 in collaboration with Technical Committee CEN/TC 332 “Laboratory equipment” the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by August 2016, and conflicting n

12、ational standards shall be withdrawn at the latest by August 2016. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document super

13、sedes EN ISO 4796-1:2000. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic

14、 of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. Endorsement notice The text of ISO 4796-1:2016 has been appro

15、ved by CEN as EN ISO 4796-1:2016 without any modification. BS EN ISO 4796-1:2016ISO 4796-1:2016(E)Foreword iv1 Scope . 12 Normative references 13 Capacities . 14 Dimensions . 15 Construction 35.1 Material . 35.2 Design . 35.3 Closures . 46 Designation 47 Marking 4 ISO 2016 All rights reserved iiiCon

16、tents PageBS EN ISO 4796-1:2016ISO 4796-1:2016(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each m

17、ember body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International

18、Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different typ

19、es of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be

20、held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents).Any trade name used in this document is informat

21、ion given for the convenience of users and does not constitute an endorsement.For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the f

22、ollowing URL: Foreword - Supplementary information.The committee responsible for this document is ISO/TC 48, Laboratory equipment.This second edition cancels and replaces the first edition (ISO 4796-1:2000), which has been technically revised to include screw-neck bottles with nominal capacities of

23、150 ml, 750 ml, and 3 500 ml.ISO 4796 consists of the following parts, under the general title Laboratory glassware Bottles: Part 1: Screw-neck bottles Part 2: Conical neck bottles Part 3: Aspirator bottlesiv ISO 2016 All rights reservedBS EN ISO 4796-1:2016INTERNATIONAL STANDARD ISO 4796-1:2016(E)L

24、aboratory glassware Bottles Part 1: Screw-neck bottles1 ScopeThis part of ISO 4796 specifies a series of screw-neck bottles suitable for the storage of fluid liquid and solid chemicals and reagents in general laboratory use. These bottles with nominal volumes ranging from 25 ml to 20 000 ml are also

25、 suitable for the preparation and storage of microbiological growth media.2 Normative referencesThe following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated refer

26、ences, the latest edition of the referenced document (including any amendments) applies.ISO 3585, Borosilicate glass 3.3 Properties3 Capacities3.1 The nominal capacities of screw-neck bottles shall be chosen from the following series: 25 ml 50 ml 100 ml 150 ml 250 ml 500 ml and 750 ml; 1 l 2 l 3,5 l

27、 5 l 10 l 15 l and 20 l.3.2 The nominal capacity of a bottle indicates the quantity of liquid which a bottle of average wall thickness shall contain when the bottle is filled to the turn of the shoulder.3.3 The design of the bottle shall be such that the total capacity to the base of the neck shall

28、be approximately 15 % greater than that to the shoulder.4 DimensionsThe dimensions and tolerances of screw-neck bottles are given in Figure 1, Figure 2, and Table 1.Table 1 DimensionsNominal capacityTotal height h1Height to shoulder h2Outside diameter d1Wall thickness sInternal neck diameter d2ml mm

29、 approx.mm approx.mm approx.mm min.mm min.25 70 41 36 1,0 12,550 87 50 46 1,0 15100 100 60 56 1,5 27150 110 70 62 1,5 27 ISO 2016 All rights reserved 1BS EN ISO 4796-1:2016ISO 4796-1:2016(E)Nominal capacityTotal height h1Height to shoulder h2Outside diameter d1Wall thickness sInternal neck diameter

30、d2ml mm approx.mm approx.mm approx.mm min.mm min.250 138 90 70 1,5 27500 176 110 86 1,5 27750 204 133 95 1,7 271 000 225 153 101 1,7 272 000 260 170 136 2,0 273 500 295 184 161 2,0 275 000 330 208 181 2,0 2710 000 410 265 227 2,7 2715 000 445 285 268 2,7 2720 000 505 330 288 3,0 27hhssg351dg351dFigu

31、re 1 Bottles with nominal capacities of 25 ml to 2 000 mlTable 1 (continued)2 ISO 2016 All rights reservedBS EN ISO 4796-1:2016ISO 4796-1:2016(E)hhsg351dg351ds190Key1 taper 1:30Figure 2 Bottles with nominal capacities of 3,5 l to 20 l5 Construction5.1 Material5.1.1 Bottles shall be constructed of cl

32、ear, colourless or amber borosilicate glass 3.3 in accordance with ISO 3585.5.1.2 Internal stress and visible defects in the glass (such as bubbles near the surface) shall be reduced to a level sufficient to minimize the possibility of fracture due to thermal or mechanical shock.5.2 Design5.2.1 The

33、base of the bottle shall be constructed so as to enable the bottle to stand firmly on a flat surface without rocking or spinning.5.2.2 The base of the bottle shall have a suitable radius so as to provide a smooth transition between the base and the side. The main portion of the side shall be cylindr

34、ical for bottles with nominal capacities of 25 ml to 2 000 ml, and slightly tapered for bottles with nominal capacities 3,5 l to 20 l with the smaller diameter at the base of the bottle.The diameters d1shall be as given in Table 1.5.2.3 The shoulder of the bottle shall have a suitable radius in orde

35、r to provide a smooth transition between the side and the conical upper proportion of the bottle. ISO 2016 All rights reserved 3BS EN ISO 4796-1:2016ISO 4796-1:2016(E)5.2.4 The upper portion of the shoulder shall be of conical shape. The transition radius from the shoulder to the neck shall be as sm

36、all as possible to be compatible with manufacturing practice.5.2.5 The bottle shall be blown so as to evenly distribute the glass in the mould avoiding sudden changes in the wall thickness. The thinnest areas shall not have a thickness less than the minimum value specified in Table 1.5.2.6 The neck

37、of the bottle shall be stoutly constructed and finished with a strengthening lip designed to facilitate pouring without liquid running down the outside of the bottle. A clip-on anti-trip ring of plastics material fitting into a slightly recessed channel on the outside of the neck is a permitted alte

38、rnative form of construction.NOTE There are suitable national standards for the dimensions and design of the thread of the screw neck.5.2.7 The outer glass surface of the bottles may be coated with a suitable plastics material as a protection and to limit leakage of liquid if the bottle is damaged.

39、The coating shall be resistant to steam sterilization at 135 C.5.3 ClosuresBottles shall be provided with closures of a suitable inert plastics material, e.g. polypropylene. Closures shall form a liquid-tight seal with the threaded bottle neck.6 DesignationIf a designation of bottles is required, th

40、is shall be by reference to this part of ISO 4796, i.e. ISO 4796-1, together with the nominal capacity of the bottle.EXAMPLE For a bottle with a nominal capacity of 500 ml, the designation would be as follows:Laboratory bottle ISO 4796-1 5007 Marking7.1 Bottles complying with this part of ISO 4796 s

41、hall be marked with the following:a) nominal capacity;b) makers and/or vendors name and/or trade mark;c) number of this International Standard, i.e. ISO 4796-1, or appropriate reference to thecorrespondending national standard.In addition, each bottle can bear an area with a surface suitable for mar

42、king with a pencil.Marks a) to c) may be moulded into the recessed base of the bottle, if the method of manufacture permits; otherwise, they may be indelibly marked, in any convenient position, by etching, sandblasting or with vitreous enamel.7.2 The closures of the bottles shall be marked with the

43、maximum permitted temperature for use or for sterilization, e.g. “max. 100 C”.NOTE Closures not marked with a temperature can only be used at ambient temperature.During sterilization, the closure may not be screwed more than one turn to enable pressure release. Otherwise, pressure increase in the bo

44、ttle can result in fracture.4 ISO 2016 All rights reservedBS EN ISO 4796-1:2016This page deliberately left blankThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services.BSI is incorporated

45、 by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.British Standards Institution (BSI)BSI Group Headquarters389 Chiswick High Road London W4 4AL UKAbout usWe bring together business, industry, government, consumers, innovators and others to

46、 shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help the

47、m achieve their goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF ver

48、sions of BSI publications, including British and adopted European and international standards, through our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer

49、 Services team.SubscriptionsOur range of subscription services are designed to make using standards easier for you. For further information on our subscription products go to British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European and international standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date. You can keep in touch with standar