BS EN ISO 5455-1995 Technical drawings - Scales《技术制图 比例尺》.pdf

1、BRITISH STANDARD BS EN ISO 5455:1995 BS308-1.4: 1995 Technical drawings Scales The European Standard EN ISO5455:1994 has the status of a British StandardBSENISO5455:1995 This British Standard, having been prepared under the direction of the Engineering Sector Board, was published under the authority

2、 of the Standards Board and comes intoeffect on 15October1995 BSI01-1999 The following BSI references relate to the work on this standard: Committee reference TDE/4 Draft announced in BSI News August1995 ISBN0580237710 Committees responsible for this British Standard The preparation of this British

3、Standard was entrusted to Technical Committee TDE/4, Engineering drawing practice, upon which the following bodies were represented: Atomic Weapons Establishment British Gas plc British Standards Society Drawing Office Material Manufacturers and Dealers Association Electricity Association Gauge and

4、Tool Makers Association HEVAC Association Institution of Chemical Engineers Institution of Engineering Designers Power Generation Contractors Association Society of British Aerospace Companies Ltd. University of Warwick Amendments issued since publication Amd. No. Date CommentsBSENISO5455:1995 BSI 0

5、1-1999 i Contents Page Committees responsible Inside front cover National foreword ii Foreword 2 Text of EN ISO 5455 3BSENISO5455:1995 ii BSI 01-1999 National foreword This British Standard has been prepared by Technical Committee TDE/4 and is the English language version of ENISO5455:1994 Technical

6、 drawings Scales, published by the European Committee for Standardization (CEN). It is identical with ISO5455:1979, published by the International Organization for Standardization (ISO). This British Standard partially supersedes BS308-1. It is envisaged that when the full range of European Standard

7、s on technical drawing is implemented BS308 will be withdrawn. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity fr

8、om legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, theEN ISO title page, pages 2 and 3 and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amend

9、ment table on theinside front cover.EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO5455 October1994 ICS01.100.10 Descriptors: Scale (ratio), designation, engineering drawings English version Technical drawings Scales (ISO5455:1979) Dessins techniques Echelles (ISO5455:1979) Technische Zeich

10、nungen Mastbe (ISO5455:1979) This European Standard was approved by CEN on1994-10-14. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists

11、and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsi

12、bility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, P

13、ortugal, Spain, Sweden, Switzerland and United Kingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1994 Copyright reserved to CEN members Ref. No. EN ISO5455:1994 EENISO5455:1994 BS

14、I 01-1999 2 Foreword This European Standard was taken over by CEN from the work of ISO/TC10, Technical drawings, product definition and related documentation, of the International Standards Organization (ISO). The Technical Board had decided to submit the final draft for Formal Vote. The result was

15、positive. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by April1995, and conflicting national standards shall be withdrawn at the latest by April1995. According to the CEN/CENELEC Internal Regulat

16、ions, the following countries are bound to implement this European Standard: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland, United Kingdom. Contents Page Foreword 2 1 Scope and field of appl

17、ication 3 2 Definitions 3 3 Designation 3 4 Inscription 3 5 Scales 3 6 Large scale drawings 3ENISO5455:1994 BSI 01-1999 3 1 Scope and field of application This International Standard specifies recommended scales and their designation for use on all technical drawings in any field of engineering. 2 D

18、efinitions 2.1 scale ratio of the linear dimension of an element of an object as represented in the original drawing to the real linear dimension of the same element of the object itself NOTEThe scale of a print may be different from that of the original drawing. 2.2 full size a scale with the ratio

19、1 : 1 2.3 enlargement scale a scale where the ratio is larger then1 : 1. It is said to be larger as its ratio increases 2.4 reduction scale a scale where the ratio is smaller than1 : 1. It is said to be smaller as its ratio decreases 3 Designation The complete designation of a scale shall consist of

20、 the word “SCALE” (or its equivalent in the language used on the drawing) followed by the indication of its ratio, as follows: SCALE1 : 1 for full size; SCALE X : 1 for enlargement scales; SCALE1 : X for reduction scales. If there is no likelihood of misunderstanding, the word “SCALE” may be omitted

21、. 4 Inscription 4.1 The designation of the scale used on the drawing shall be inscribed in the title block of the drawing. 4.2 Where it is necessary to use more than one scale on a drawing, the main scale only shall be inscribed in the title block, and all other scales adjacent to the item reference

22、 number of the part concerned, or adjacent to the reference letter of a detail view (orsection). 5 Scales 5.1 The recommended scales for use on technical drawings are specified in the following table. NOTEIf, for special applications, there is need for a larger enlargement scale or a smaller reducti

23、on scale than those shown in the table, the recommended range of scales may be extended in either direction, provided that the required scale be derived from a recommended scale by multiplying by whole number powers of10. In exceptional cases where for functional reasons the recommended scales canno

24、t be applied, intermediate scales may be chosen. 5.2 The scale to be chosen for a drawing will depend upon the complexity of the object to be depicted and the purpose of the representation. In all cases, the selected scale shall be large enough to permit easy and clear interpretation of the informat

25、ion depicted. The scale and the size of the object, in turn, will decide the size of the drawing. 5.3 Details that are too small for complete dimensioning in the main representation shall be shown adjacent to the main representation in a separate detail view (or section) which is drawn to a larger s

26、cale. 6 Large scale drawings It is recommended that, for information, a full size view be added to the large scale representation of a small object. In this case the full size view may be simplified by showing the outlines of the object only. Category Recommended scales Enlargement 50 : 1 20 : 1 10

27、: 1 scales 5 : 1 2 : 1 Full size 1 : 1 1 : 2 1 : 5 1 : 10 Reduction 1 : 20 1 : 50 1 : 100 scales 1 : 200 1 : 500 1 : 1000 1 : 2000 1 : 5000 1 : 10000BSI 389 Chiswick High Road London W4 4AL | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |

28、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in

29、Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our p

30、roducts and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offer

31、s members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 899

32、6 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international s

33、tandards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up

34、 to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyr

35、ight, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwi

36、se without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070.