1、 g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58monomeric diisocyanates in isocyanate resinsThe European Standard EN ISO 10283:2007 has the status
2、of a British StandardICS 87.060.20Binders for paints and varnishes Determination of BRITISH STANDARDBS EN ISO 10283:2007BS EN ISO 10283:2007This British Standard was published under the authority of the Standards Policy and Strategy Committe on 28 September 2007 BSI 2007ISBN 978 0 580 59009 2Amendme
3、nts issued since publicationAmd. No. Date Commentscontract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.National forewordThis British Standard is the UK implementation of EN ISO 10283:2007. It supersedes BS EN ISO
4、 10283:2006 which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee STI/3, Paints, media and related products.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the
5、 necessary provisions of a EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN ISO 10283September 2007ICS 87.060.20English VersionBinders for paints and varnishes - Determination of monomericdiisocyanates in isocyanate resins (ISO 10283:2007)Liants pour peintures et vernis - Dtermination desdiisocyana
6、tes monomres dans les rsines isocyanates(ISO 10283:2007)Bindemittel fr Beschichtungsstoffe - Bestimmung vonmonomeren Diisocyanaten in Isocyanatharzen (ISO10283:2007)This European Standard was approved by CEN on 21 August 2007.CEN members are bound to comply with the CEN/CENELEC Internal Regulations
7、which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European S
8、tandard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national st
9、andards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Ki
10、ngdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2007 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN ISO 10283:2007: E3 Fo
11、reword This document (EN ISO 10283:2007) has been prepared by Technical Committee ISO/TC 35 “Paints and varnishes“ in collaboration with Technical Committee CEN/TC 139 “Paints and varnishes“, the secretariat of which is held by DIN. This European Standard shall be given the status of a national stan
12、dard, either by publication of an identical text or by endorsement, at the latest by March 2008, and conflicting national standards shall be withdrawn at the latest by March 2008. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are b
13、ound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden,
14、 Switzerland and the United Kingdom. Endorsement notice The text of ISO 10283:2007 has been approved by CEN as a EN ISO 10283:2007 without any modification. EN ISO 10283:2007Reference numberISO 10283:2007(E)INTERNATIONAL STANDARD ISO10283Second edition2007-09-01Binders for paints and varnishes Deter
15、mination of monomeric diisocyanates in isocyanate resins Liants pour peintures et vernis Dtermination des diisocyanates monomres dans les rsines isocyanates EN ISO 10283:2007ii iiiContents Page Foreword iv Introduction v 1 Scope . 1 2 Normative references . 1 3 Terms and definitions. 1 4 Principle.
16、2 5 Reagents 2 6 Apparatus 2 7 Sampling 3 8 Procedure 3 8.1 Operating conditions 3 8.2 Column conditioning 8 8.3 Gas-chromatographic determination 8 9 Expression of results . 9 9.1 Determination of calibration factor. 9 9.2 Calculation of the monomeric diisocyanate content 9 10 Precision 9 10.1 Repe
17、atability (r). 9 10.2 Reproducibility (R) 10 11 Test report . 10 EN ISO 10283:2007iv Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out thr
18、ough ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collabo
19、rates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Stand
20、ards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of
21、this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 10283 was prepared by Technical Committee ISO/TC 35, Paints and varnishes, Subcommittee SC 10, Test methods for binders for paints and varnishes. This second editio
22、n cancels and replaces the first edition (ISO 10283:1997), in which the normative references clause has been updated. EN ISO 10283:2007vIntroduction It is well-known fact that, due to the production methods used, all the commercial isocyanate resins named in this standard contain a certain amount of
23、 volatile monomeric isocyanates. This amount is generally less than 0,5 % relative to the resin as supplied. In view of the regulations relating to the handling of hazardous substances, it has become a matter of special concern that a generally accepted and applicable method of determination should
24、be available. This standard is not intended to present a method suitable for the analytical determination of volatile isocyanates in any form and in any quantity. The standard specifies a method confined to determining the amounts of volatile isocyanates which occur in practice in isocyanate resins,
25、 namely about 0,1 % to 0,4 %. A further objective of the standard was to develop a method for determining with adequate accuracy as many as possible of the monomeric isocyanates which occur in isocyanate resins. It detects the principle isocyanates, namely toluene diisocyanate (TDI), hexamethylene d
26、iisocyanate (HDI), diphenylmethane diisocyanate (MDI) and isophorone diisocyanate (IPDI), and is a method considered by industry, authorities and institutes alike to be the state of the art. EN ISO 10283:2007blank1Binders for paints and varnishes Determination of monomeric diisocyanates in isocyanat
27、e resins 1 Scope This International Standard specifies a gas-chromatographic method for determining monomeric diisocyanates such as toluene diisocyanate1), hexamethylene diisocyanate, isophorone diisocyanate2), diphenylmethane diisocyanate3)and other diisocyanates in isocyanate resins as defined in
28、Clause 3 and in solutions prepared from such resins, insofar as these are used in the formulation of paints and similar coating materials. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited ap
29、plies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 15528, Paints, varnishes and raw materials for paints and varnishes Sampling 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1
30、isocyanate resin synthetic resin, with or without solvent, based on aromatic, aliphatic or cycloaliphatic isocyanates containing isocyanate (NCO) groups NOTE For the purposes of this International Standard, such isocyanate resins comprise: those which are manufactured from any diisocyanate, in parti
31、cular toluene diisocyanate (TDI), hexamethylene diisocyanate (HDI), isophorone diisocyanate (IPDI) or diphenylmethane diisocyanate (MDI), and which contain urethane and/or biuret and/or isocyanurate groups; those which are prepared from mixtures of the isocyanate resins given above. 1) The term “tol
32、uene diisocyanate” is used here and in the following text for 4-methyl-1,3-phenylene diisocyanate (2,4-toluene diisocyanate) and 2-methyl-1,3-phenylene diisocyanate (2,6-toluene diisocyanate). 2) The term “isophorone diisocyanate” is used here and in the following text for 2-isocyanatomethyl)-3,5,5-
33、trimethylcyclohexylisocyanate. The stereoisomers are identified at the appropriate points in the text by (I) and (II). 3) The term “diphenylmethane diisocyanate” is used here and in the following text for 4,4-diisocyanatodiphenylmethane, 2,4-diisocyanatodiphenylmethane and 2,2-diisocyanatodiphenylme
34、thane. EN ISO 10283:20072 4 Principle The content of monomeric diisocyanate in isocyanate resins is determined by gas chromatography, using tetradecane or, in the case of diisocyanates of low volatility, anthracene as the internal standard. 5 Reagents During the analysis, use only reagents of recogn
35、ized analytical grade. 5.1 Ethyl acetate, anhydrous (dried with 0,5 nm molecular sieve) and ethanol-free (ethanol content 0,5 but u 1 1 1 but u 2 0,5 2 but u 4 0,2 4 0,1 Weigh the test sample to the nearest 0,1 mg (mass m0) into a conical flask (6.2). Using the pipette (6.3), add 10 ml of the intern
36、al-standard solution (5.7)4). Add about 25 ml of ethyl acetate, close the conical flask and shake well to dissolve the test sample. NOTE The test sample can also be weighed to the nearest 0,1 mg into a 50 ml sample bottle fitted with a septum seal. Add about (15 0,1) mg of the internal standard to t
37、he sample bottle. Dissolve the sample in 40 ml of ethyl acetate. Examine 1 l of this solution (test solution) by gas chromatography. The following sequence shall be observed for each determination: inject calibration solution at least twice; inject test solution twice. 4) Approx. 15 mg of the intern
38、al standard weighed to an accuracy of 0,1 mg can be used instead of the standard solution. EN ISO 10283:200799 Expression of results 9.1 Determination of calibration factor From each calibration chromatogram, calculate the calibration factor f, using the following equation: DI StSt DImAfmA=where mSt
39、is the mass of internal standard (tetradecane or anthracene) in the internal-standard solution (5.7); mDIis the mass of monomeric diisocyanate in the reference solution (5.8); ADIis the peak area for the monomeric diisocyanate contained in the reference solution; AStis the peak area for the internal
40、 standard. 9.2 Calculation of the monomeric diisocyanate content Calculate the content of monomeric diisocyanate wDIfrom the peak areas, using the following equation: 12DI21mA fwmA=where m1is the mass of internal standard in the test solution; m2is the mass of test sample; A2is the peak area for the
41、 monomeric diisocyanate in the test solution; A1is the peak area for the internal standard in the test solution. Calculate the mean of two determinations, this mean being corrected by the average value of the calibration factor f calculated for each determination. Detection limit: 0,01 % (by mass) o
42、f the monomeric diisocyanate under the conditions specified in 8.1. 10 Precision for a content of monomeric diisocyanate of (0,50 0,05) % (by mass). 10.1 Repeatability (r) The value below which the absolute difference between two single test results, each the mean of duplicates, obtained on identica
43、l material by one operator in one laboratory within a short interval of time using the standardized test method may be expected to lie with a 95 % probability is 0,02 %. EN ISO 10283:200710 10.2 Reproducibility (R) The value below which the absolute difference between two test results, each the mean
44、 of duplicates, obtained on identical material by operators in different laboratories using the standardized test method may be expected to lie with a 95 % probability is 0,05 %. 11 Test report The test report shall contain at least the following information: a) all details necessary to identify the
45、 product tested; b) a reference to this International Standard (ISO 10283); c) the individual values and means of the content of monomeric diisocyanates (as indicated in 9.2); d) any deviation from the method specified; e) the date of the test. EN ISO 10283:2007blankBS EN ISO BSI389 Chiswick High Ro
46、adLondonW4 4AL10283:2007BSI British Standards InstitutionBSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amen
47、dment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard wo
48、uld inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the lat
49、est editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-.In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested.Information o
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1