1、BRITISH STANDARDBS EN ISO 10424-2:2007Petroleum and natural gas industries Rotary drilling equipment Part 2: Threading and gauging of rotary shouldered thread connectionsThe European Standard EN ISO 10424-2:2007 has the status of a British StandardICS 75.180.10g49g50g3g38g50g51g60g44g49g42g3g58g44g5
2、5g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58BS EN ISO 10424-2:2007This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 December
3、 2007 BSI 2007ISBN 978 0 580 53477 5National forewordThis British Standard is the UK implementation of EN ISO 10424-2:2007.The UK participation in its preparation was entrusted by Technical Committee PSE/17, Materials and equipment for petroleum, petrochemical and natural gas industries, to Panel PS
4、E/17/-/4, Drilling and production equipment for petroleum and natural gas industries.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for it
5、s correct application.Compliance with a British Standard cannot confer immunity from legal obligations. Amendments issued since publicationAmd. No. Date CommentsEUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN ISO 10424-2November 2007ICS 75.180.10English VersionPetroleum and natural gas industries
6、- Rotary drilling equipment- Part 2: Threading and gauging of rotary shouldered threadconnections (ISO 10424-2:2007)Industries du ptrole et du gaz naturel - quipements deforage rotary - Partie 2: Filetage et calibrage desconnexions rotary filetes paulement (ISO 10424-2:2007)Erdl- und Erdgasindustrie
7、 - Bohr- und Frderanlagen - Teil2: Verschraubungen, Kalibrierung und Prfung vondrehenden Schulteransatz-Gewindeverbindungen (ISO10424-2:2007)This European Standard was approved by CEN on 2 November 2007.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the con
8、ditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three
9、 official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austr
10、ia, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTE
11、E FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2007 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN ISO 10424-2:2007: EForeword This document (E
12、N ISO 10424-2:2007) has been prepared by Technical Committee ISO/TC 67 “Materials, equipment and offshore structures for petroleum and natural gas industries“ in collaboration with Technical Committee CEN/TC 12 “Materials, equipment and offshore structures for petroleum, petrochemical and natural ga
13、s industries” the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2008, and conflicting national standards shall be withdrawn at the latest by May 2008.
14、According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
15、Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of ISO 10424-2:2007 has been approved by CEN as a EN ISO 10424-2:2007 without any modification. EN ISO 10424-2:2007
16、Reference numberISO 10424-2:2007(E)INTERNATIONAL STANDARD ISO10424-2First edition2007-11-15Petroleum and natural gas industries Rotary drilling equipment Part 2: Threading and gauging of rotary shouldered thread connections Industries du ptrole et du gaz naturel quipements de forage rotary Partie 2:
17、 Filetage et calibrage des connexions rotary filetes paulement EN ISO 10424-2:2007ii iiiContents Page Foreword. v Introduction . vi 1 Scope 1 2 Conformance Units of measurement 1 3 Normative references 2 4 Terms, abbreviated terms, definitions and symbols2 4.1 Terms and definitions .2 4.2 Design typ
18、es and definitions4 4.3 Abbreviations and symbols6 5 Information to be supplied by purchaser8 6 Threading8 6.1 Thread profile and dimensions 8 6.2 Bevels for drill collars and tools that mate directly with drill collars.15 6.3 Low-torque feature 16 7 Product optional features .18 7.1 General18 7.2 S
19、tress-relief features .18 7.3 Benchmarks .21 7.4 Surface treatment 23 7.5 Cold working 23 7.6 Break-in.23 8 Product gauging 23 8.1 Gauging 23 8.2 Stand-off measurement.24 8.3 Gauge contact points 24 8.4 Lead measurement 25 8.5 Taper measurement.27 8.6 Thread height measurement and gauges .27 9 Gauge
20、 relationships for rotary shouldered connections 27 9.1 Gauge relationship 27 9.2 Gauge specifications.28 10 Gauge calibration.40 10.1 Calibration system.40 10.2 Acceptance criteria40 10.3 Gauge measurement methods .40 10.4 Gauge certification 46 Annex A (informative) Tables in USC units 47 Annex B
21、(informative) Care and use of regional master gauges .56 Annex C (normative) Shipment of reference master gauges .58 Annex D (normative) Care and use of working gauges 60 Annex E (informative) API gauge certification requirements .61 Annex F (informative) Other rotary shouldered connections.64 Annex
22、 G (informative) USC units conversion table .85 EN ISO 10424-2:2007iv Annex H (informative) Recommended practice for gauging new rotary shouldered connections 86 Annex I (informative) Calculations 92 Annex J (informative) API grand and regional master rotary connection gauges 96 EN ISO 10424-2:2007v
23、Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a t
24、echnical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters
25、 of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulate
26、d to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible
27、for identifying any or all such patent rights. ISO 10424-2 was prepared by Technical Committee ISO/TC 67, Materials, equipment and offshore structures for petroleum, petrochemical and natural gas industries, Subcommittee SC 4, Drilling and production equipment. ISO 10424 consists of the following pa
28、rts, under the general title Petroleum and natural gas industries Rotary drilling equipment: Part 1: Rotary drill stem elements Part 2: Threading and gauging of rotary shouldered thread connections EN ISO 10424-2:2007vi Introduction This International Standard is based on API Spec 7, Specification f
29、or rotary drill stem elements. Users of this International Standard should be aware that further or differing requirements may be needed for individual applications. This International Standard is not intended to inhibit a vendor from offering, or the purchaser from accepting, alternative equipment
30、or engineering solutions for the individual application. This may be particularly applicable where there is innovative or developing technology. Where an alternative is offered, the vendor should identify any variations from this International Standard and provide details. EN ISO 10424-2:20071Petrol
31、eum and natural gas industries Rotary drilling equipment Part 2: Threading and gauging of rotary shouldered thread connections 1 Scope This part of ISO 10424 specifies requirements on rotary shouldered connections for use in petroleum and natural gas industries, including dimensional requirements on
32、 threads and thread gauges, stipulations on gauging practice, gauge specifications, as well as instruments and methods for inspection of thread connections. These connections are intended primarily for use in drill-string components. Other supplementary specifications can be agreed between intereste
33、d parties for special tolerance requirements, qualification, testing, inspection and finishing. This part of ISO 10424 is applicable to the following preferred rotary shouldered connection designs: a) number (NC) style; b) regular (REG) style; c) full hole (FH) style. These are traceable to an inter
34、nationally supported system of gauges and calibration 2 Conformance Units of measurement In this part of ISO 10424, data are expressed in both the International System (SI) of units and the United States Customary (USC) system of units. Separate tables for data expressed in SI units and USC units ar
35、e given in the body of this part of ISO 10424 and Annex A, respectively. Figures express data in both SI and USC units. For a specific order item, it is intended that only one system of units be used, without combining data expressed in the other system. Annex G provides the conversion between SI an
36、d USC units used in this part of ISO 10424. Products manufactured to specifications expressed in either of these unit systems shall be considered equivalent and totally interchangeable. Consequently, compliance with the requirements of this part of ISO 10424 as expressed in one system provides compl
37、iance with requirements expressed in the other system. For data expressed in the SI system, a comma is used as the decimal separator and a space as the thousands separator. For data expressed in the USC system, a dot (on the line) is used as the decimal separator and a space as the thousands separat
38、or. In the text, data in SI units are followed by data in USC units in brackets. EN ISO 10424-2:20072 3 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the la
39、test edition of the referenced document (including any amendments) applies. ISO 10424-1, Petroleum and natural gas industries Rotary drilling equipment Part 1: Rotary drill stem elements ISO 119611), Petroleum and natural gas industries Steel drill pipe ISO/IEC 17025, General requirements for the co
40、mpetence of testing and calibration laboratories API Spec 7, Specification for Rotary Drill Stem Elements 4 Terms, abbreviated terms, definitions and symbols 4.1 Terms and definitions For the purposes of this document, the following terms and definitions apply. 4.1.1 bevel diameter outside diameter
41、of the contact face of the rotary shouldered connection 4.1.2 box connection box end threaded connection on oil country tubular goods with internal (female) threads 4.1.3 box thread internal (female) threads of a rotary shouldered connection 4.1.4 break-in procedure applied to newly manufactured thr
42、eads to assure correct mating 4.1.5 calibration system documented system of gauge calibration and control 4.1.6 cold working plastic deformation of the surface of the connection at a temperature low enough to induce strain hardening 4.1.7 first perfect thread thread furthest from the sealing face on
43、 a pin, or closest to the sealing face on a box, where both the crest and the root are fully formed 4.1.8 full-depth thread thread in which the thread root lies on the minor cone of an external thread or lies on the major cone of an internal thread 1) To be published. (Revision of ISO 11961:1996) EN
44、 ISO 10424-2:200734.1.9 gauge point imaginary plane, perpendicular to the thread axis of rotary shouldered connections at which the pitch diameter, C, at gauge point is measured NOTE This plane is located 15,875 mm (0.625 0 in) from the make-up shoulder of the pin thread. 4.1.10 interchange stand-of
45、f stand-off between each member of a gauge set and a corresponding gauge next higher in the ranking scheme: grand master or regional master, reference master, working gauge 4.1.11 lead distance parallel to the thread axis from a point on a thread turn and the corresponding point on the next turn, i.
46、e. the axial displacement of a point following the helix one turn around the thread axis 4.1.12 make-up shoulder sealing shoulder on a rotary shouldered connection 4.1.13 manufacturer firm, company or corporation that operates facilities capable of cutting the threads and is responsible for complian
47、ce with all the applicable provisions of this part of ISO 10424 4.1.14 master gauge gauges used for calibration of other gauges NOTE These include reference master, regional master and grand master gauges. 4.1.15 mating stand-off stand-off between the plug and ring members of a gauge set NOTE Interc
48、hange stand-off is the stand-off between each member and a gauge higher in the ranking scheme. 4.1.16 pin connection pin end threaded connection on oil country tubular goods with external (male) threads 4.1.17 pin thread external (male) threads of a rotary shouldered connection 4.1.18 pitch axial di
49、stance between successive threads, which, in a single start thread, is equivalent to lead 4.1.19 pitch cone imaginary cone whose diameter at any point is equal to the pitch diameter of the thread at the same point 4.1.20 pitch diameter diameter at which the distance across the threads is equal to the distance between the threads EN ISO 10424-2:20074 4.1.21 product drill string component with rotary shouldered connection in accordance with this part of ISO 10424 4.1.22 reference dimension dimension that is a result of two or more other dime
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1