BS EN ISO 13397-3-1997 Periodontal curettes dental scalers and excavators Dental scalers H-type《牙周刮匙 牙刮除器和牙挖器 洗牙器 H型》.pdf

1、BRITISH STANDARD BS EN ISO 13397-3:1997 Periodontal curettes, dental scalers and excavators Part 3: Dental scalers H-type The European Standard EN ISO 13397-3:1996 has the status of a British Standard ICS 11.060.20BSEN ISO 13397-3:1997 This British Standard, having been prepared under the direction

2、of the Health and Environment Sector Board, was published under the authority of the Standards Board and comes into effect on 15 April 1997 BSI 12-1998 The following BSI references relate to the work on this standard: Committee reference CH/52 Draft for comment 94/504198 DC ISBN 0 580 26681 8 Commit

3、tees responsible for this British Standard The preparation of this British Standard was entrusted to Technical Committee CH/52, Dental instruments, upon which the following bodies were represented: British Dental Association British Dental Trade Association British Endodontic Society British Society

4、 for Restorative Dentistry British Society for the Study of Prosthetic Dentistry Department of Health Ministry of Defence Amendments issued since publication Amd. No. Date CommentsBS EN ISO 13397-3:1997 BSI 12-1998 i Contents Page Committees responsible Inside front cover National foreword ii Forewo

5、rd 2 Text of EN ISO 13397-3 1 List of references Inside back coverBSEN ISO 13397-3:1997 ii BSI 12-1998 National foreword This British Standard has been prepared by Technical Committee CH/52 and is the English language version of EN ISO 13397-3:1996 Periodontal curettes, dental scalers and excavators

6、 Part 3: Dental scalers H-type, published by the European Committee for Standardization (CEN). It is identical with ISO 13397-3:1996 published by the International Organization for Standardization (ISO). EN ISO 13397-3 was produced as a result of international discussion in which the United Kingdom

7、took an active part. BS EN ISO 13397 supersedes BS 2965:1970, which was withdrawn on the publication of BS EN ISO 13397-1. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance w

8、ith a British Standard does not of itself confer immunity from legal obligations. Cross-references Publication referred to Corresponding British Standard ISO 1942-3:1989 BS EN 21942 Dental vocabulary Part 3:1994 Dental instruments ISO 13397-1:1995 BS EN ISO 13397-1:1996 Periodontal curettes, dental

9、scalers and excavators Part 1: General requirements Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, theEN ISO title page, page 2, the ISO title page, pages ii to iv, pages 1 to 6, aninside back cover and a back cover. This standard has been updated (see

10、 copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on theinside front cover.EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 13397-3 September 1996 ICS 11.060.00 Descriptors: Dentistry, dental equipment, dental instruments, dimensions, di

11、mensional measurements English version Periodontal curettes, dental scalers and excavators Part 3: Dental scalers, H-type (ISO 13397-3:1996) Curettes parodontales, instruments dentaires pour dtartrage et excavateurs dentaires Partie 3: Instruments dentaires pour dtartrage (ISO 13397-3:1996) Parodont

12、alkretten, Zahnreiniger und Exkavatoren Teil 3: Zahnreiniger H-Typ (ISO 13397-3:1996) This European Standard was approved by CEN on 1996-06-01. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a n

13、ational standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in

14、 any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Denmark, Finland, France, Germany, Greece, I

15、celand, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1996 Copyright reserved

16、to CEN members Ref. No. EN ISO 13397-3:1996 EENISO 13397-3:1996 BSI 12-1998 2 Foreword The text of the International Standard ISO 13397-3:1996 has been prepared by Technical Committee ISO/TC 106, Dentistry, in collaboration with Technical Committee CEN/TC 55 Dentistry, the secretariat of which is he

17、ld by DIN. ISO 13397 consists of the following parts, under the general title Periodontal curettes, dental scalers and excavators: Part 1: General requirements; Part 2: Periodontal curettes Gr-type; Part 3: Dental scalers H-type; Part 4: Dental excavators Discoid-type. It is anticipated that additio

18、nal types of instruments will form the subject of future parts. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by March 1997, and conflicting national standards shall be withdrawn at the latest by M

19、arch 1997. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal

20、, Spain, Sweden, Switzerland and the United Kingdom.EN ISO 13397-3:1996 ii BSI 12-1998 Contents Page Foreword iii 1 Scope 1 2 Normative references 1 3 Definitions 1 4 Design and dimensions 1 Figure 1 Dental scalers H-types 3 and 4 (chisel) 2 Figure 2 Dental scalers H-type 5 (cleoid) 2 Figure 3 Denta

21、l scalers H-types 6 and 7 (sickle) 3 Figure 4 Dental scalers H-type 8 (cleoid) 4 Figure 5 Dental scalers H-type 9 (cleoid) 5 Table 1 Dimensions of H-type scalers 5 Table 2 Points of measurement for H-type scalers 6EN ISO 13397-3:1996 BSI 12-1998 iii Foreword ISO (the International Organization for S

22、tandardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the ri

23、ght to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. Draft Intern

24、ational Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75% of the member bodies casting a vote. International Standard ISO 13397-3 was prepared by Technical Committee ISO/TC 106, Den

25、tistry, Subcommittee SC 4, Dental instruments. ISO 13397 consists of the following parts, under the general title Periodontal curettes, dental scalers and excavators: Part 1: General requirements; Part 2: Periodontal curettes Gr-type; Part 3: Dental scalers H-type; Part 4: Dental excavators Discoid-

26、type. It is anticipated that additional types of instruments will form the subject of future parts.iv blankEN ISO 13397-3:1996 BSI 12-1998 1 1 Scope This part of ISO13397 specifies the dimensions for H-type dental scalers. 2 Normative references The following standards contain provisions which, thro

27、ugh reference in this text, constitute provisions of this part of ISO 13397. At the time of publication, the editions indicated were valid. All standards are subject to revision, and parties to agreements based on this part of ISO 13397 are encouraged to investigate the possibility of applying the m

28、ost recent editions of the standards indicated below. Members of IEC and ISO maintain registers of currently valid International Standards. ISO 1942-3:1989, Dental vocabulary Part 3: Dental instruments. ISO 13397-1:1995, Periodontal curettes, dental scalers and excavators Part 1: General requirement

29、s. 3 Definitions For the purposes of this part of ISO 13397, the definitions given in ISO 1942-3 and the following definitions apply. 3.1 dental scaler hand instrument for removing calculus and other accretions from the surface of teeth 3.2 glaze surface working surface of the instrument formed duri

30、ng production of the cutting edge(s) 4 Design and dimensions General requirements for dental scalers are specified in ISO 13397-1. Dental scalers shall have the designs shown in Figure 1 to Figure 5 and the dimensions as given in Table 1. The points of measurement associated with the dimensions are

31、listed in Table 2. Annex A of ISO 13397-1 provides details of one method of measurement applicable to most types of dental hand instrument. 4.1 Overall length The maximum overall length, irrespective of the design of the instrument, shall be 178 mm.EN ISO 13397-3:1996 2 BSI 12-1998 Figure 1 Dental s

32、calers H-types 3 and 4 (chisel) Figure 2 Dental scalers H-type 5 (cleoid)EN ISO 13397-3:1996 BSI 12-1998 3 Figure 3 Dental scalers H-types 6 and 7 (sickle)EN ISO 13397-3:1996 4 BSI 12-1998 Figure 4 Dental scalers H-type 8 (cleoid)EN ISO 13397-3:1996 BSI 12-1998 5 Table 1 Dimensions of H-type scalers

33、 Figure 5 Dental scalers H-type 9 (cleoid) Dimensions in millimetres (angular dimensions in degrees) Type b 1 0,15 b 2 0,1 b 3 h 1 0,3 h 2 0,5 l 1 0,7 r 1 a 5 b 3 H3 (chisel) 2 0,4 12 min. 1,5 6 50 H4 (chisel) 1,5 0,4 12 min. 1,2 6 50 H5 (cleoid) 0,7 1 3,2 0,3 3,8 5 10,7 120 H6 (sickle) 1 0,9 7 min.

34、 2,8 4 5,7 5 17 H7 (sickle) 1 0,9 7 min. 2,8 4 5,7 5 17 H8 (cleoid) 0,7 1 3,2 0,3 5,5 10,1 120 H9 (cleoid) 0,7 1 3,2 0,3 5,5 10,1 120 EN ISO 13397-3:1996 6 BSI 12-1998 Table 2 Points of measurement for H-type scalers Dimension Point of measurement b 1 Blade width Measured at the widest point, unless

35、 a specific cross-section is indicated by AA, BB, ., ZZ at a set distance from the datum point. b 2 Blade thickness Measured at the thickest point, unless a specific cross-section is indicated by AA, BB, ., ZZ at a set distance from the datum point. b 3 Blade length Distance measured from the extrem

36、e tip of the blade, parallel to the centreline of the blade, to the blade/shank interface. h 1 Blade height Distance measured from the datum point, at right angles to the centreline of the instrument, to the farthest extremity of the blade. h 2 Shank height Distance measured from the datum point, at

37、 right angles to the centreline of the instrument, to the farthest external surface of the first bend of the shank. l 1 Length to first bend Distance measured from the datum point, parallel to the centreline of the instrument, to the highest point on the first bend. r 1 Radius of blade Radius of cur

38、vature of the inside of the blade (reference dimension only). a Blade angle Angle of glaze surface to the centreline of the blade, shank or instrument, whichever is appropriate. b Offset angle With the instrument viewed at 90 to the standard position (i.e. a plan view) the angle between the centreli

39、ne of the shank and a line, parallel to the centreline of the instrument, forming a tangent with the first bend of the instrument.BS EN ISO 13397-3:1997 BSI 12-1998 List of references See national foreword.BSI 389 Chiswick High Road London W4 4AL | | | | | | | | | | | | | | | | | | | | | | | | | | |

40、 | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BSI British Standards Institution BSI is the independent national body responsible for preparing Br

41、itish Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It i

42、s the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front

43、 cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be address

44、ed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range

45、 of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. F

46、ax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Copyright Copyright s

47、ubsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by

48、 any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070.