BS EN ISO 13845-2015 Plastics piping systems Elastomeric-sealing-ring-type socket joints for use with thermoplastic pressure pipes Test method for leaktightness under internal pres.pdf

1、BSI Standards PublicationBS EN ISO 13845:2015Plastics piping systems Elastomeric-sealing-ring-typesocket joints for use withthermoplastic pressure pipes Test method for leaktightnessunder internal pressure andwith angular deflectionBS EN ISO 13845:2015 BRITISH STANDARDNational forewordThis British S

2、tandard is the UK implementation of EN ISO 13845:2015. It supersedes BS EN ISO 13845:2000 which iswithdrawn.The UK participation in its preparation was entrusted to Technical Committee PRI/88/4, Test Methods - Plastic Piping.A list of organizations represented on this committee can be obtained on re

3、quest to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2015.Published by BSI Standards Limited 2015ISBN 978 0 580 81753 3 ICS 23.040.01; 23.040.20; 91.140.60

4、Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 28 February 2015.Amendments/corrigenda issued since publicationDate T e x t a f f e c t e dEUROPEAN STANDARD NORM

5、E EUROPENNE EUROPISCHE NORM EN ISO 13845 February 2015 ICS 91.140.60; 23.040.20; 23.040.01 Supersedes EN ISO 13845:2000English Version Plastics piping systems - Elastomeric-sealing-ring-type socket joints for use with thermoplastic pressure pipes - Test method for leaktightness under internal pressu

6、re and with angular deflection (ISO 13845:2015) Systmes de canalisations en plastiques - Assemblages par emboture bague dtanchit en lastomre pour les tubes sous pression plastiques - Mthode dessai dtanchit sous pression interne et avec dviation angulaire (ISO 13845:2015) Kunststoff-Rohrleitungssyste

7、me - Steckmuffenverbindungen mit elastomeren Dichtringen fr Rohre aus Thermoplasten - Prfverfahren fr die Dichtheit unter Innendruck und Abwinkelung (ISO 13845:2015) This European Standard was approved by CEN on 24 January 2015. CEN members are bound to comply with the CEN/CENELEC Internal Regulatio

8、ns which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. T

9、his European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN me

10、mbers are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Port

11、ugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2015 CEN All rights of exploitation in any f

12、orm and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 13845:2015 EBS EN ISO 13845:2015Foreword This document (EN ISO 13845:2015) has been prepared by Technical Committee ISO/TC 138 “Plastics pipes, fittings and valves for the transport of fluids” in collaboration with Tec

13、hnical Committee CEN/TC 155 “Plastics piping systems and ducting systems” the secretariat of which is held by NEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by August 2015, and conflicting nati

14、onal standards shall be withdrawn at the latest by August 2015. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersed

15、es EN ISO 13845:2000. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of

16、Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. Endorsement notice The text of ISO 13845:2015 has been approved b

17、y CEN as EN ISO 13845:2015 without any modification. EN ISO 13845:2015 (E)BS EN ISO 13845:2015ISO 13845:2015(E)Foreword iv1 Scope . 12 Principle 13 Test parameters and requirements 14 Apparatus . 15 Test pieces preparation . 26 Procedure. 27 Test report . 3Annex A (normative) Test parameters . 5 ISO

18、 2015 All rights reserved iiiContents PageBS EN ISO 13845:2015ISO 13845:2015(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through IS

19、O technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates c

20、losely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteri

21、a needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives). Attention is drawn to the possibility that some of the elements of this document may be the subject of p

22、atent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents). Any trade name u

23、sed in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical B

24、arriers to Trade (TBT) see the following URL: Foreword - Supplementary informationThe committee responsible for this document is ISO/TC 138, Plastics pipes, fittings and valves for the transport of fluids, Subcommittee SC 5, General properties of pipes, fittings and valves of plastic materials and t

25、heir accessories Test methods and basic specifications.This second edition cancels and replaces the first edition (ISO 13845:2000) which has been technically revised. The reason for modification is for applicability to other plastics materials, other sizes, and/or other test conditions and alignment

26、 with texts of other International Standards on test methods.The modifications are the following: no material is mentioned; test parameters are omitted, although the original test parameters can be found in Annex A; editorial changes have been introduced.iv ISO 2015 All rights reservedBS EN ISO 1384

27、5:2015Plastics piping systems Elastomeric-sealing-ring-type socket joints for use with thermoplastic pressure pipes Test method for leaktightness under internal pressure and with angular deflectionWARNING Persons using this International Standard should be familiar with normal laboratory practice, i

28、f applicable. The use of this International Standard may involve hazardous materials, operations, and equipment. This International Standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this International Standard to

29、 establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.1 ScopeThis International Standard specifies a method for testing the leak tightness under internal pressure with angular deflection of assembled joints between elastomeric-seali

30、ng-ring-type sockets made of plastic or metal and plastic pressure pipes.2 PrincipleA joint assembly as test piece consisting of a plastic pipe mounted into a socket is subjected, within a specified temperature range, to a specified internal pressure regime for a specified test period while the pipe

31、 is also subject to an angular deflection in the socket. While under pressure, the test piece is monitored for signs of leakage.3 Test parameters and requirementsThe test parameters of the International Standard which refers to this test International Standard shall be used and the requirements shal

32、l be fulfilled. If one or more parameters are not given in the referring International Standard, the ones given in Annex A shall apply.NOTE The following test parameters should be given by the International Standard which refers to this test International Standard:a) test medium;b) test pressure bar

33、 or MPa;c) test duration h;d) test temperature C;e) angle of deflection () ;f) free length mm.4 Apparatus4.1 Framework, comprising at least two fixing devices, one of which is movable to allow angular deflection to be applied to the test joint. A typical arrangement is shown in Figure 1.INTERNATIONA

34、L STANDARD ISO 13845:2015(E) ISO 2015 All rights reserved 1BS EN ISO 13845:2015ISO 13845:2015(E)4.2 A pressure control device, connected to the test piece and capable of applying and maintaining a variable internal hydrostatic pressure of up to at least twice the nominal pressure of the plastic pipe

35、 and joint assembly.4.3 Pressure measuring device, capable of checking conformity to the specified static pressure values (see 6.6 and Figure A.1).Key1 starting point for measuring and adjusting the angle of deflection L free length of the pipe between the socket mouth and the end-sealdnnominal outs

36、ide diameter of the pipeFigure 1 Typical test arrangement5 Test pieces preparationThe test piece shall comprise an assembly of a plastic pipe section mounted into the socket to be tested.The fittings and pipes shall not be tested until 24 h after their production. For practical reasons, the manufact

37、urer can wait a shorter time before testing. In case of dispute, a duration of 24 h shall apply.The assembly shall be carried out in accordance with the socket manufacturers instructions.A pipe of the same nominal pressure (PN) or the same pipe series S as that of the socket shall be used for the te

38、st.The mean outside diameter, dem, of the pipe should preferably conform to the minimum specified value, and the socket dimensions (mean inside diameter, dim, and the diameter of the groove for housing the sealing ring) should preferably conform to the maximum values stated by the manufacturer, in o

39、rder to have dimensions as close as possible to the extreme limits of their relevant tolerances.6 Procedure6.1 Secure the socket, without any deformation, to the solid framework and align the pipe section with the axis of the socket.6.2 By inclining the pipe in the test apparatus, determine the free

40、 angle of deflection, free, which the joint can tolerate without the application of force.If the free angle of deflection is greater or equal to the required one, firmly anchor the pipe to maintain the deflected pipe in this position for the remainder of the test.2 ISO 2015 All rights reservedBS EN

41、ISO 13845:2015ISO 13845:2015(E)If the free angle of deflection is less than the required one, carry out the test at the required deflection measured at the starting point (see Figure 1), by forcing the pipe to that position.6.3 Fill the test piece with the test medium at the specified temperature. I

42、f water is used as test medium, ensure all air is removed and excluded from the test piece for the remainder of the procedure.6.4 Condition the test piece to ensure equalization of temperature.Minimum conditioning times are given in Table 1.Table 1 Conditioning periodsNominal wall thickness of the p

43、ipe mmMinimum conditioning period mine 10 2010 e 20 6020 e 1206.5 While testing in accordance with 6.6:a) maintain the specified temperature within 2 C;b) examine the joint during the whole test cycle and record any sign of leakage.NOTE If air is used as test medium, leakage can be detected with lea

44、k detection fluid.6.6 Apply the specified test regime so that the specified static pressures are maintained within a permitted deviation of 05+%.7 Test reportThe test report shall include the following information:a) a reference to this International Standard (i.e. ISO 13845:2015) and the referring

45、International Standard;b) the nominal pressure class or S series of the components e.g. fitting(s), pipe comprising the joint(s) under test;c) all details necessary for identification of the test pieces, including the nominal size of the pipes and fittings used to produce the test pieces, the type o

46、f material, and the manufacturers code;d) the angle of deflection, , used for the test;e) the test temperature;f) the test duration;g) the test procedure;h) the maximum test pressure;i) if any sign of leakage was observed and the pressure at which this occurred;j) information on the leak tightness o

47、f the joint including the pressure at which a leakage occurred (if any);k) any factors which may have affected the results, such as any incidents or any operating details not specified in this International Standard; ISO 2015 All rights reserved 3BS EN ISO 13845:2015ISO 13845:2015(E)l) the date of t

48、he test.4 ISO 2015 All rights reservedBS EN ISO 13845:2015ISO 13845:2015(E)Annex A (normative) Test parametersThe test parameters in Table A.1 shall be used, if applicable.Table A.1 Test parametersTest mediumTest duration minTest temperature CAngle of deflection Test pressure MPaWater See Figure A.1

49、 20 5 2 See Figure A.1The length of the pipe section shall be such that the free length, L, between the socket mouth and the end-seal is equal to five times the nominal outside diameter of the pipe with a minimum of 500 mm and a maximum of 1 500 mm.KeyX time, minY factor fFigure A.1 Pressure test regimeNOTE The pressure changes need not be at a linear rate.The test pressure ptshall be calculated by multiplying the factor f indicated in Figure A.1 by the nominal pressure PN, i.e. by using For