BS EN ISO 13856-1-2013 Safety of machinery Pressure-sensitive protective devices General principles for design and testing of pressure-sensitive mats and pressure-sensitive floors《.pdf

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN ISO 13856-1:2013Safety of machinery Pressure-sensitive protectivedevicesPart 1: General principles for design andtesting of pressure-sensitive mats andpressure-sensitive fl

2、oors (ISO 13856-1:2013)BS EN ISO 13856-1:2013 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN ISO13856-1:2013. It supersedes BS EN 1760-1:1997+A1:2009 which iswithdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee MCE/3, Safeguardi

3、ng of machinery.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2013. Published

4、 by BSI StandardsLimited 2013ISBN 978 0 580 72191 5ICS 13.110; 29.120.50Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 30 April 2013.Amendments issued since publi

5、cationDate Text affectedEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 13856-1 April 2013 ICS 13.110 Supersedes EN 1760-1:1997+A1:2009English Version Safety of machinery - Pressure-sensitive protective devices - Part 1: General principles for design and testing of pressure-sensitive mats a

6、nd pressure-sensitive floors (ISO 13856-1:2013)Scurit des machines - Dispositifs de protection sensibles la pression - Partie 1: Principes gnraux de conception et dessai des tapis et planchers sensibles la pression (ISO 13856-1:2013) Sicherheit von Maschinen - Druckempfindliche Schutzeinrichtungen -

7、 Teil 1: Allgemeine Leitstze fr die Gestaltung und Prfung von Schaltmatten und Schaltplatten (ISO 13856-1:2013) This European Standard was approved by CEN on 7 March 2013. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this Europea

8、n Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (

9、English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgi

10、um, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzer

11、land, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2013 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref

12、. No. EN ISO 13856-1:2013: EBS EN ISO 13856-1:2013EN ISO 13856-1:2013 (E) 3 Foreword This document (EN ISO 13856-1:2013) has been prepared by Technical Committee ISO/TC 199 “Safety of machinery“ in collaboration with Technical Committee CEN/TC 114 “Safety of machinery” the secretariat of which is he

13、ld by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 2013, and conflicting national standards shall be withdrawn at the latest by October 2013. Attention is drawn to the possibility

14、that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 1760-1:1997+A1:2009. This document has been prepared under a mandate given to CEN by the Europea

15、n Commission and the European Free Trade Association, and supports essential requirements of EU Directive. For relationship with EU Directive, see informative Annex ZA, which is an integral part of this document. According to the CEN-CENELEC Internal Regulations, the national standards organizations

16、 of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, N

17、etherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. Endorsement notice The text of ISO 13856-1:2013 has been approved by CEN as EN ISO 13856-1:2013 without any modification. BS EN ISO 13856-1:2013EN ISO 13856-1:2013 (E) 4 Anne

18、x ZA (informative) Relationship between this European Standard and the Essential Requirements of EU Directive 2006/42/EC This European Standard has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association to provide a means of conforming to Essent

19、ial Requirements of the New Approach Directive Machinery 2006/42/EC. Once this standard is cited in the Official Journal of the European Union under that Directive and has been implemented as a national standard in at least one Member State, compliance with the normative clauses of this standard giv

20、en in Table ZA.1 confers, within the limits of the scope of this standard, a presumption of conformity with the corresponding Essential Requirements of that Directive and associated EFTA regulations. Table ZA.1 Correspondence between this European Standard and Directive 2006/42/EC Clause(s)/sub-clau

21、se(s) of this European Standard Essential Requirements (ERs) of Directive 2006/42/EC Qualifying remarks/Notes Clause 4 Annex I, 1.2 Control systems Annex I, 1.3 Protection against mechanical hazards Annex I, 1.4 Required characteristics of (guards and) protection devices Annex I, 1.5 Risks due to ot

22、her hazards Annex I, 1.6 Maintenance Clauses 5 and 6 Annex I, 1.7 Information WARNING Other requirements and other EU Directives may be applicable to the product(s) falling within the scope of this standard. BS EN ISO 13856-1:2013ISO 13856-1:2013(E) ISO 2013 All rights reserved iiiContents PageForew

23、ord vIntroduction vi1 Scope . 12 Normative references 13 Terms and definitions . 24 Requirements for design and testing 34.1 General . 34.2 Actuating force 54.3 Response time 74.4 Static loading 74.5 Number of operations . 74.6 Output state of sensor . 74.7 Response of output signal switching device

24、(s) to actuating force . 84.8 Access for maintenance . 84.9 Adjustments 84.10 Connections . 94.11 Environmental conditions . 94.12 Power supply . 104.13 Electrical equipment . 104.14 Enclosure 114.15 Performance levels and categories for SRP/CSs in accordance with ISO 13849-1 .114.16 Sensor fittings

25、 . 124.17 Tripping 124.18 Slip-resistance 124.19 Additional coverings of top surfaces of sensor(s) .134.20 Failure due to blocking or wedging 135 Marking .135.1 General 135.2 Marking of control unit . 135.3 Marking of sensor 135.4 Marking of other components 136 Information for use .136.1 General 13

26、6.2 Instructions for use 147 Testing 167.1 General 167.2 Sensor test sample 177.3 Test pieces for load tests 177.4 Test No. 1 Actuating force 187.5 Test No. 2 Response time . 207.6 Test No. 3 Static loading 227.7 Test No. 4 Number of operations 227.8 Test No. 5 Output state of sensor 277.9 Test No.

27、6 Response of output signal switching device to actuating force 287.10 Test No. 7 Access for maintenance 287.11 Test No. 8 Adjustments 287.12 Test No. 9 Connections . 287.13 Test No. 10 Environmental conditions . 287.14 Test No. 11 Electrical power supply . 307.15 Test No. 12 Electrical equipment 30

28、7.16 Test No. 13 Enclosure 307.17 Test No. 14 PL according to ISO 13849-1 30BS EN ISO 13856-1:2013ISO 13856-1:2013(E)iv ISO 2013 All rights reserved7.18 Test No. 15 Slip-resistance 307.19 Test No. 16 Additional coverings of top surfaces of sensor(s) 307.20 Test No. 17 Failure due to blocking or wedg

29、ing .31Annex A (normative) Timing diagrams for pressure-sensitive mats/floors with/without reset 32Annex B (informative) Application notes .35Annex C (informative) Design notes .40Annex D (informative) Installation, commissioning and testing .45Bibliography .47BS EN ISO 13856-1:2013ISO 13856-1:2013(

30、E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a

31、technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matter

32、s of electrotechnical standardization.International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated

33、 to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible fo

34、r identifying any or all such patent rights.ISO 13856-1 was prepared by Technical Committee ISO/TC 199, Safety of machinery and by Technical Committee CEN/TC 114, Safety of machinery in collaboration.This second edition cancels and replaces the first edition (ISO 13856-1:2001) which has been technic

35、ally revised.ISO 13856 consists of the following parts, under the general title Safety of machinery Pressure-sensitive protective devices: Part 1: General principles for design and testing of pressure-sensitive mats and pressure-sensitive floors Part 2: General principles for design and testing of p

36、ressure-sensitive edges and pressure-sensitive bars Part 3: General principles for design and testing of pressure-sensitive bumpers, plates, wires and similar devices ISO 2013 All rights reserved vBS EN ISO 13856-1:2013ISO 13856-1:2013(E)IntroductionThe structure of safety standards in the field of

37、machinery is as follows:a) Type-A standards (basic safety standards) giving basic concepts, principles for design, and general aspects that can be applied to all machinery;b) Type-B standards (generic safety standards) dealing with one safety aspect or one type of safeguard that can be used across a

38、 wide range of machinery: Type-B1 standards on particular safety aspects (e.g. safety distances, surface temperature, noise); Type-B2 standards on safeguards (e.g. two-hand controls, interlocking devices, pressure-sensitive devices, guards);c) Type-C standards (machine safety standards) dealing with

39、 detailed safety requirements for a particular machine or group of machines.This document is a type-B2 standard as stated in ISO 12100.The requirements of this document can be supplemented or modified by a type-C standard.For machines which are covered by the scope of a type-C standard and which hav

40、e been designed and built according to the requirements of that standard, the requirements of that type-C standard take precedence.The safeguarding of machinery (see ISO 12100:2010, 3.21) can be achieved by many different means. These means include guards which prevent access to the hazard zone by m

41、eans of a physical barrier (for example, interlocking guards according to ISO 14119 or fixed guards according to ISO 14120) and protective devices (for example, electro-sensitive protective equipment according to IEC 61496-1 or pressure-sensitive protective devices according to this part of ISO 1385

42、6).Type-C standards makers and designers of machinery/installations consider the best way to achieve the required level of safety taking into account the intended application and the results of the risk assessment (see ISO 12100).The required solution can also be to combine several of these differen

43、t means: the machinery/installation supplier and the user examine together carefully the existing hazards and constraints before making their decision on the choice of safeguarding.Pressure-sensitive protective devices are used in a wide range of applications with different conditions of use relatin

44、g, for example, to extremes of loading or electrical, physical and chemical environments. They are interfaced with machine controls to ensure that the machine reverts to a safe condition if the sensitive protective equipment is actuated.ISO 13856 is restricted to the design of pressure-sensitive pro

45、tective devices so that they can be used when the risk assessment carried out by the machine manufacturer and/or relevant type-C standard, when available, shows this to be appropriate.vi ISO 2013 All rights reservedBS EN ISO 13856-1:2013Safety of machinery Pressure-sensitive protective devices Part

46、1: General principles for design and testing of pressure-sensitive mats and pressure-sensitive floors1 ScopeThis part of ISO 13856 establishes general principles and specifies requirements for the design and testing of pressure-sensitive mats and pressure-sensitive floors normally actuated by the fe

47、et for use as devices for protecting persons from hazardous machinery. The minimum safety requirements for the performance, marking and documentation are given.This part of ISO 13856 is applicable to pressure-sensitive mats and pressure-sensitive floors, regardless of the type of energy used (e.g. e

48、lectrical, hydraulic, pneumatic or mechanical), designed to detect persons weighing more than 35 kg, and persons (e.g. children) weighing more than 20 kg.It is not applicable to the detection of persons weighing less than 20 kg.It does not specify the following because they are application-specific:

49、a) dimensions or configuration of the effective sensing area of pressure-sensitive mat(s) or pressure-sensitive floor(s) in relation to any particular application;b) when pressure-sensitive mats or floors are appropriate in a particular situation;c) performance levels (PLs) for safety-related parts of control systems (SRP/CSs) other than providing a minimum level.This part of ISO 13856 gives guidance to assist the user (i.e. machinery manufacturer and/or user of the machinery) in providing an adequate arra