1、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BRITISH STANDARD BS EN ISO 14530-1:2000 Th
2、e European Standard EN ISO 14530-1:1999 has the status of a British Standard ICS 83.080.10 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Plastics Unsaturated-polyester powder moulding compounds (UP-PMCs) Part 1: Designation system and basis for specificationsThis British Sta
3、ndard, having been prepared under the direction of the Sector Committee for Materials and Chemicals, was published under the authority of the Standards Committee and comes into effect on 15 January 2000 BSI 01-2000 ISBN 0 580 35885 2 BS EN ISO 14530-1:2000 Amendments issued since publication Amd. No
4、. Date Comments National foreword This British Standard is the English language version of EN ISO 14530-1:1999. It is identical with ISO 14530-1:1999. The UK participation in its preparation was entrusted to Technical Committee PRI/42, Fibre reinforced thermosetting plastics and prepregs, which has
5、the responsibility to: aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in th
6、e UK. A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references Attention is drawn to the fact that CEN and CENELEC Standards normally include an annex which lists normative references to international publications with their corresponding Eu
7、ropean publications. The British Standards which implement these international or European publications may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A
8、British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a
9、front cover, an inside front cover, the EN ISO title page, the EN ISO foreword page, the ISO title page, pages ii and iii, a blank page, pages 1 to 6, an inside back cover and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued.EN ISO 14530-1
10、:1999 Referencenumber ISO14530-1:1999(E) INTERNATIONAL STANDARD ISO 14530-1 Firstedition 1999-11-15 PlasticsUnsaturated-polyesterpowder mouldingcompounds(UP-PMCs) Part1: Designationsystemandbasisfor specifications Plastiques Poudres mouler base de polyester non satur (UP-PMC) Partie 1: Systme de dsi
11、gnation et base de spcification EN ISO 14530-1:1999ISO-035411:(9991E) ISO9991 Allrgihtsresvrede.lnUesstorehwisescepfieid,noraptofthisilbupctaoinmaybeudorpercedorutziliedinnayformorbynaysnaem,electnoric ormecinahcal,inclidungtohpociypongnadmicrfoilm,wituohteprmissioninwritingfromeitehrISOattherddaess
12、leboworISOsmemebrydob inthectnuoryofthertseuqee.r ISOcirypohgtfofice aCsesoptale56 121-HC1veneGa20 leT.+41224790111 aFx+41223741097 E-mailcirypothgiso.ch Webwww.iso.ch ii DPFdcsilremia ihTsPDFfilemayctnoainemeddebdtyfepaces.InaccnadrocewithAebodslicensinglopicy,thisfilemaybepirntedorivewedubtslahlto
13、n beidetedlnuessthetyfepaceswhichareemeddebdraelicensedtonadintslaledonthecomputerfrepormingtheideting.Inodwlnidaongthis feli,trapiesaccepttierehnthesersnoptilibiyofontinfrnignigAebodslicsneniglopicy.hTeISOtneCarlSecterairatacceptsnollibaiityinthis .aera AbodeisatdaremarkofAbodeStsyemsInctaropro.de
14、teDailsofthesfotwraepudorctsusedtocrtaeetihsPDFfilecanbefnuodintheGarenelInfolerativetothefile;theP-FDcerationrapamteers weretpoimizedforpirtning.EvreycraeahseebntakentoensruethatthefileissuitlbaeforusebyISOmemebridobse.Inthelnuikleyetnev tahtaplboremleratingtoitisfdnuo,lpaeseifnormthetneCarlSectera
15、iratattheserddasgivenlebow. EN ISO 14530-1:1999ISO-035411:(9991E)iii Foreword ISO(theInternationalOrganizationforStandardization)isaworldwidefederationofnationalstandardsbodies(ISO memberbodies).TheworkofpreparingInternationalStandardsisnormallycarriedoutthroughISOtechnical committees.Eachmemberbody
16、interestedinasubjectforwhichatechnicalcommitteehasbeenestablishedhas therighttoberepresentedonthatcommittee.Internationalorganizations,governmentalandnon-governmental,in liaisonwithISO,alsotakepartinthework.ISOcollaboratescloselywiththeInternationalElectrotechnical Commission(IEC)onallmattersofelect
17、rotechnicalstandardization. InternationalStandardsaredraftedinaccordancewiththerulesgivenintheISO/IECDirectives,Part3. DraftInternationalStandardsadoptedbythetechnicalcommitteesarecirculatedtothememberbodiesforvoting. PublicationasanInternationalStandardrequiresapprovalbyatleast75%ofthememberbodiesc
18、astingavote. AttentionisdrawntothepossibilitythatsomeoftheelementsofthispartofISO14530maybethesubjectof patentrights.ISOshallnotbeheldresponsibleforidentifyinganyorallsuchpatentrights. InternationalStandardISO14530-1waspreparedbyTechnicalCommitteeISO/TC61, Plastics, Subcommittee SC12, Thermosetting
19、materials. ISO14530consistsofthefollowingparts,underthegeneraltitle Plastics Unsaturated-polyester powder moulding compounds (UP-PMCs): Part 1: Designation system and basis for specifications Part 2: Preparation of test specimens and determination of properties Part 3: Requirements for selected moul
20、ding compounds EN ISO 14530-1:1999EN ISO 14530-1:1999INTERNATIONAL STANDARD ISO 14530-1:1999(E) ISO 9991 All irhgts seredevr 1 Plastics Unsaturated-polyester powder moulding compounds (UP-PMCs) Part 1: Designation system and basis for specifications 1 Scope 1.1 This part of ISO 14530 establishes a d
21、ata block system for the designation of unsaturated-polyester powder moulding compounds (UP-PMCs). 1.2 The various types of UP-PMC are differentiated from each other by a classification system based on information about the filler/reinforcement type and content, the intended method of processing, an
22、y special properties and those of the special properties used specifically for designation purposes (designatory properties). 1.3 This part of ISO 14530 is applicable to all UP-PMCs ready for normal use in the form of powder, granules or ground material. 1.4 It is not intended to imply that material
23、s having the same designation necessarily give the same performance. This part of ISO 14530 does not provide engineering data, performance data or data on processing conditions which may be required to specify a material for a particular application and/or method of processing. If such additional pr
24、operties are required, they shall be determined in accordance with the test methods specified in ISO 14530-2, if suitable. 1.5 Whenever general requirement data, as covered by ISO 14530-3, need to be indicated, this is also done using this data block system. 1.6 To ensure that code-letters and code-
25、numbers remain unambiguous, and to avoid conflicts within the system, any new code-letters or code-numbers for use in data block 1, 2 or 3 shall be approved before use by the secretariats of ISO/TC 61/SC 1, SC 12 and SC 13. 2 Normative references The following normative documents contain provisions
26、which, through reference in this text, constitute provisions of this part of ISO 14530. For dated references, subsequent amendments to, or revisions of, any of these publications do not apply. However, parties to agreements based on this part of ISO 14530 are encouraged to investigate the possibilit
27、y of applying the most recent editions of the normative documents indicated below. For undated references, the latest edition of the normative document referred to applies. Members of ISO and IEC maintain registers of currently valid International Standards. ISO 75-2:1993, Plastics Determination of
28、temperature of deflection under load Part 2: Plastics and ebonite. ISO 179-1: 1) , Plastics Determination of Charpy impact properties Part 1: Non-instrumented impact test. 1) To be published. (Revision of ISO 179:1993) EN ISO 14530-1:1999 1ISO -035411:(9991E) 2 ISO 9991 All irhgts seredevr ISO 472:1
29、999, Plastics Vocabulary. ISO 1043-1:1997, Plastics Symbols and abbreviated terms Part 1: Basic polymers and their special characteristics. ISO 1043-2: 2) , Plastics Symbols and abbreviated terms Part 2: Fillers and reinforcing materials. ISO 14530-2:1999, Plastics Unsaturated-polyester powder mould
30、ing compounds (UP-PMCs) Part 2: Preparation of test specimens and determination of properties. ISO 14530-3:1999, Plastics Unsaturated-polyester powder moulding compounds (UP-PMCs) Part 3: Requirements for selected moulding compounds. 3 Terms and definitions For the purposes of this part of ISO 14530
31、, the terms and definitions given in ISO 472 and ISO 14530-2 apply, plus the following: 3.1 powder moulding compound powder, granules or ground material capable of flowing freely through the feed systems of processing machines, as well as moulding compounds in the form of flakes which are normally n
32、ot thought of as powders The abbreviation for powder moulding compound is PMC by analogy with bulk moulding compound (BMC) and sheet moulding compound (SMC). 3.2 UP-PMC abbreviation for powder moulding compounds based on unsaturated-polyester resins for both injection and compression moulding 4 Desi
33、gnation system 4.1 General The designation system defined in this part of ISO 14530 is based on the following standardized pattern: Designation Identity block Description ISO Individual-item block block Standard Data block 1 Data block 2 Data block 3 Data block 4 Data block 5 The designation consist
34、s of an optional description block, reading “PMC“, and an identity block comprising the International Standard number and an individual-item block. For unambiguous designation, the individual-item block is subdivided into five data blocks comprising the following information: 2) To be published. (Re
35、vision of ISO 1043-2:1988) EN ISO 14530-1:1999 2ISO -035411:(9991E) ISO 9991 All irhgts seredevr 3 Data block 1: Marking block Item 1: Identification of the basic polymer by its symbol, in accordance with ISO 1043-1; Item 2: Nature of the designatory reinforcement materials or fillers, in accordance
36、 with ISO 1043-2; Item 3: Form of the designatory reinforcement materials or fillers, in accordance with ISO 1043-2; Item 4: Nominal content of the designatory reinforcement materials or fillers, in accordance with Table 1. Data block 2: Method of processing Method of processing for which the mouldi
37、ng compound is intended, designated in accordance with Table 2. Data block 3: Properties Item 1: Special properties, in accordance with Table 3; Item 2: Designatory property No. 1 impact strength determined in accordance with ISO 179-1; Item 3: Designatory property No. 2 temperature resistance deter
38、mined in accordance with ISO 75-2. Data block 4: Further information, taken from an international, national or company standard. Data block 5 (optional): Additional requirements The first character of the individual-item block shall be a hyphen. The data blocks shall be separated from each other by
39、commas. If a data block is not used, this shall be indicated by an “X“ (= not applicable), but only if another block follows. For labelling purposes, and provided no other blocks follow, the comma between blocks 1 and 2 can be omitted. There is no need to fill in data blocks if they are not required
40、. 4.2 Data block 1 Item 1: After the hyphen, unsaturated-polyester powder moulding compounds shall be identified by the symbol UP, in accordance with ISO 1043-1. Mixtures and modifications shall be designated in accordance with ISO 1043-1:1997, subclauses 4 and 5. The following information shall be
41、restricted to designatory fillers/reinforcements used in the material in question: Item 2: Nature of filler/reinforcement, in accordance with Table 1. Item 3: Form of filler/reinforcement, in accordance with Table 1. Item 4: Nominal content (mass %) of filler/reinforcement, in accordance with Table
42、1. Note, in particular, the following: the same code-letters have different meanings when used for item 2 and item 3; whenever information needs to be indicated only for item 3, an “X“ ( = not applicable) is required for item 2. EN ISO 14530-1:1999 3ISO -035411:(9991E) 4 ISO 9991 All irhgts seredevr
43、 4.3 Data block 2 In this data block, information about the method of processing is given using the code-letters specified in Table 2. The code-letter used to indicate the intended method of processing in data block 2 shall be selected carefully. Certain brands of material can be processed in more t
44、han one way, e.g. either by compression moulding (Q) or by injection moulding (M). Such brands shall be designated “general purpose“ (G). The designation of special methods of processing shall be reserved for specially modified materials. Table 1 Code-letters and code-numbers used in data block 1 Na
45、ture of filler/reinforcement (in accordance with ISO 1043-2) Form of filler/reinforcement (in accordance with ISO 1043-2) Percentage content by mass, w % (m/m) C D E G K L1 L2 M P Q R S T W X Z Carbon Aluminium oxide trihydrate Clay Glass Calcium carbonate Cellulose Cotton Mineral Mica Silica Recycl
46、ed material Synthetic organic Talc Wood Not specified Others B C D F G S X Z Balls; beads; spheres Chips; cuttings Fines; powder Fibre Ground Scale; flakes Not specified Others 05 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 w7 , 5 7,5u w 12,5 12,5u w 17,5 17,5u w 22,5 22,5u w 27,5 27,5u w
47、32,5 32,5u w 37,5 37,5u w 42,5 42,5u w 47,5 47,5u w 52,5 52,5u w 57,5 57,5u w 62,5 62,5u w 67,5 67,5u w 72,5 72,5u w 77,5 77,5u w 82,5 82,5u w 87,5 87,5u w 92,5 92,5u w 97,5 NOTE Mixtures of materials and/or forms may be indicated by combining the relevant codes using the sign “+“ and placing the wh
48、ole between parentheses. For example, a mixture of 20 % glass fibre (GF) and 20 % mineral dust (MD) would be indicated by (GF20+MD20). Table 2 Code-letters used in data block 2 for the method of processing G General purpose T Transfer moulding M Injection moulding X Not specified Q Compression mould
49、ing Z Others EN ISO 14530-1:1999 4ISO -035411:(9991E) ISO 9991 All irhgts seredevr 5 4.4 Data block 3 4.4.1 General In this data block, the special properties (see 4.4.2) are represented by a code-letter as item 1, and the designatory properties (see 4.4.3 and 4.4.4) as items 2 and 3. Items 2 and 3 each start with an oblique stroke. If the value of a designatory property falls on or near a range limit, the manufacturer shall state which range will designate the material. If subsequent ind
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1