BS EN ISO 14583-2011 Hexalobular socket pan head screws《内六角花形盘头螺钉 》.pdf

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN ISO 14583:2011Hexalobular socket pan headscrews (ISO 14583:2011)BS EN ISO 14583:2011 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN I

2、SO14583:2011. It supersedes BS EN ISO 14583:2001 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee FME/9/3, Fasteners - Product Standards.A list of organizations represented on this committee can beobtained on request to its secretary.This publication doe

3、s not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. BSI 2011ISBN 978 0 580 71159 6ICS 21.060.10Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of

4、theStandards Policy and Strategy Committee on 30 April 2011.Amendments issued since publicationDate Text affectedEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 14583 March 2011 ICS 21.060.10 Supersedes EN ISO 14583:2001English Version Hexalobular socket pan head screws (ISO 14583:2011) Vis

5、 mtaux tte cylindrique bombe large six lobes internes (ISO 14583:2011) Flachkopfschrauben mit Innnensechsrund (ISO 14583:2011) This European Standard was approved by CEN on 31 January 2011. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for g

6、iving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three o

7、fficial versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies

8、 of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingd

9、om. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2011 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 14583:2011: EBS

10、EN ISO 14583:2011EN ISO 14583:2011 (E) 3 Foreword This document (EN ISO 14583:2011) has been prepared by Technical Committee ISO/TC 2 “Fasteners“ in collaboration with Technical Committee CEN/TC 185 “Fasteners” the secretariat of which is held by DIN. This European Standard shall be given the status

11、 of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2011, and conflicting national standards shall be withdrawn at the latest by September 2011. Attention is drawn to the possibility that some of the elements of this document may be the s

12、ubject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN ISO 14583:2001. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to impleme

13、nt this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switz

14、erland and the United Kingdom. Endorsement notice The text of ISO 14583:2011 has been approved by CEN as a EN ISO 14583:2011 without any modification. BS EN ISO 14583:2011ISO 14583:2011(E) ISO 2011 All rights reserved iiiForeword ISO (the International Organization for Standardization) is a worldwid

15、e federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that

16、 committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in ac

17、cordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard req

18、uires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 14583 was prepared by Techni

19、cal Committee ISO/TC 2, Fasteners, Subcommittee SC 10, Product standards for fasteners. This second edition cancels and replaces the first edition (ISO 14583:2001), of which it constitutes a minor revision. It also incorporates the Technical Corrigendum ISO 14583:2001/Cor.1:2004. BS EN ISO 14583:201

20、1BS EN ISO 14583:2011INTERNATIONAL STANDARD ISO 14583:2011(E) ISO 2011 All rights reserved 1Hexalobular socket pan head screws 1 Scope This International Standard specifies the characteristics of hexalobular socket pan head screws of product grade A and with thread sizes from M2 up to and including

21、M10. If, in special cases, specifications other than those listed in this International Standard are required, they can be selected from existing International Standards, for example ISO 261, ISO 888, ISO 898-1, ISO 965-2, ISO 3506-1 and ISO 4759-1. 2 Normative references The following referenced do

22、cuments are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 225, Fasteners Bolts, screws, studs and nuts Symbols and descriptions of

23、 dimensions ISO 261, ISO general-purpose metric screw threads General plan ISO 898-1, Mechanical properties of fasteners made of carbon steel and alloy steel Part 1: Bolts, screws and studs with specified property classes Coarse thread and fine pitch thread ISO 965-2, ISO general purpose metric scre

24、w threads Tolerances Part 2: Limits of sizes for general purpose external and internal screw threads Medium quality ISO 3269, Fasteners Acceptance inspection ISO 3506-1, Mechanical properties of corrosion-resistant stainless steel fasteners Part 1: Bolts, screws and studs ISO 4042, Fasteners Electro

25、plated coatings ISO 4759-1, Tolerances for fasteners Part 1: Bolts, screws, studs and nuts Product grades A, B and C ISO 6157-1, Fasteners Surface discontinuities Part 1: Bolts, screws and studs for general requirements ISO 8839, Mechanical properties of fasteners Bolts, screws, studs and nuts made

26、of non-ferrous metals ISO 8992, Fasteners General requirements for bolts, screws, studs and nuts ISO 10664, Hexalobular internal driving feature for bolts and screws ISO 10683, Fasteners Non-electrolytically applied zinc flake coatings BS EN ISO 14583:2011ISO 14583:2011(E) 2 ISO 2011 All rights rese

27、rved3 Dimensions See Figure 1 and Table 1. Symbols and descriptions of dimensions are specified in ISO 225. NOTE The shank diameter, ds, is approximately equal to the pitch diameter or equal to the major thread diameter. aAs-rolled end. Figure 1 BS EN ISO 14583:2011ISO 14583:2011(E) ISO 2011 All rig

28、hts reserved 3Table 1 Dimensions Dimensions in millimetres Thread, d M2 M2,5 M3 (M3,5)aM4 M5 M6 M8 M10 P b0,4 0,45 0,5 0,6 0,7 0,8 1,0 1,25 1,5 a max. 0,8 0,9 1 1,2 1,4 1,6 2 2,5 3 b min. 25 25 25 38 38 38 38 38 38 damax. 2,6 3,1 3,6 4,1 4,7 5,7 6,8 9,2 11,2 nom. = max. 4,0 5,0 5,6 7,00 8,00 9,50 12

29、,00 16,00 20,00 dkmin. 3,7 4,7 5,3 6,64 7,64 9,14 11,57 15,57 19,48 nom. = max. 1,60 2,10 2,40 2,60 3,10 3,70 4,6 6,0 7,50 k min. 1,46 1,96 2,26 2,46 2,92 3,52 4,3 5,7 7,14 r min. 0,1 0,1 0,1 0,1 0,2 0,2 0,25 0,4 0,4 rf 3,2 4 5 6 6,5 8 10 13 16 x max. 1,0 1,1 1,25 1,5 1,75 2,0 2,5 3,2 3,8 Socket no.

30、 6 8 10 15 20 25 30 45 50 A ref. 1,75 2,4 2,8 3,35 3,95 4,5 5,6 7,95 8,95 max. 0,77 1,04 1,27 1,33 1,66 1,91 2,42 3,18 4,02 Hexalobular socketct min. 0,63 0,91 1,01 1,07 1,27 1,52 2,02 2,79 3,62 l dnom.amin. max. Approximate mass of carbon steel screws, in kilograms per 1 000 pieces (r = 7,85 kg/dm3

31、) (for information only) 3 2,8 3,2 0,178 0,336 4 3,76 4,24 0,196 0,366 0,544 5 4,76 5,24 0,215 0,396 0,588 0,891 1,30 6 5,76 6,24 0,233 0,426 0,632 0,951 1,38 2,32 8 7,71 8,29 0,270 0,486 0,720 1,07 1,53 2,57 4,37 10 9,71 10,29 0,307 0,546 0,808 1,19 1,69 2,81 4,72 9,96 12 11,65 12,35 0,344 0,606 0,

32、896 1,31 1,84 3,06 5,07 10,6 19,8 (14) 13,65 14,35 0,381 0,666 0,984 1,43 2,00 3,31 5,42 11,2 20,5 16 15,65 16,35 0,418 0,726 1,07 1,55 2,15 3,56 5,78 11,9 21,8 20 19,58 20,42 0,492 0,846 1,25 1,79 2,46 4,05 6,48 13,2 23,8 25 24,58 25,42 0,996 1,47 2,09 2,85 4,67 7,36 14,8 26,3 30 29,58 30,42 1,69 2

33、,39 3,23 5,29 8,24 16,4 28,8 35 34,5 35,5 2,68 3,62 5,91 9,12 18,0 31,3 40 39,5 40,5 4,01 6,52 10,0 19,6 33,9 45 44,5 45,5 7,14 10,9 21,2 36,4 50 49,5 50,5 7,76 11,8 22,8 38,9 (55) 54,4 55,6 12,6 24,4 41,4 60 59,4 60,6 13,5 26,0 43,9 NOTE Preferred lengths are the ones between the solid, bold, stepp

34、ed lines. a Sizes in parentheses should be avoided, if possible. b P is the pitch of the thread. c For the acceptance of the hexalobular socket and for gauges, see ISO 10664. d Screws with nominal lengths above the discontinuous, stepped line are threaded up to the head (b = l a). BS EN ISO 14583:20

35、11ISO 14583:2011(E) 4 ISO 2011 All rights reserved4 Specifications and reference International Standards See Table 2. Table 2 Specifications and reference International Standards Material Steel Stainless steel Non-ferrous metal General requirements International Standard ISO 8992 Tolerance class 6g

36、Thread International Standard ISO 261, ISO 965-2 Property class 4.8 A2-70 A3-70 As agreed Mechanical property International Standard ISO 898-1 ISO 3506-1 ISO 8839 Product grade A Tolerance International Standard ISO 4759-1 Hexalobular socket International Standard ISO 10664 As processed As processed

37、 As processed Requirements for electroplating are specified in ISO 4042.Requirements for electroplating are specified in ISO 4042.Requirements for non-electrolytically applied zinc flake coatings are specified in ISO 10683. Finish Coating Additional requirements or other finishes or coatings shall b

38、e agreed between the supplier and the purchaser. Surface integrity Limits for surface discontinuities are specified in ISO 6157-1. Acceptability Acceptance inspection is specified in ISO 3269. 5 Designation EXAMPLE A hexalobular socket pan head screw with thread M5, nominal length l = 20 mm and prop

39、erty class 4.8 is designated as follows: Hexalobular socket pan head screw ISO 14583 - M5 20 - 4.8 BS EN ISO 14583:2011ISO 14583:2011(E) ISO 2011 All rights reserved 5Bibliography 1 ISO 888, Bolts, screws and studs Nominal lengths, and thread lengths for general purpose bolts This page deliberately

40、left blankThis page deliberately left blankBSI is the independent national body responsible for preparing British Standardsand other standards-related publications, information and services. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Ch

41、arter.British Standards Institution (BSI)raising standards worldwideBSI Group Headquarters389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards are updated by amendment or revision. Users of British Stan-dards should make sure that they possess the latest amendm

42、ents or editions.It is the constant aim of BSI to improve the quality of our products and serv-ices. We would be grateful if anyone finding an inaccuracy or ambiguity whileusing this British Standard would inform the Secretary of the technical com-mittee responsible, the identity of which can be fou

43、nd on the inside frontcover.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001BSI offers Members an individual updating service called PLUS which ensuresthat subscribers automatically receive the latest editions of standards.Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001Email: Buying standardsYou

44、may buy PDF and hard copy versions of standards directly using acredit card from the BSI Shop on the website addition all orders for BSI, international and foreign standards publicationscan be addressed to BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001Email: In response to

45、orders for international standards, it is BSI policy tosupply the BSI implementation of those that have been publishedas British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, Europeanand international standards through its Knowled

46、ge Centre.Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005Email: Various BSI electronic information services are also available whichgive details on all its products and services. Tel: +44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048Email: BSI Subscribing Members are kept up to date with standardsdevel

47、opments and receive substantial discounts on the purchase priceof standards. For details of these and other benefits contact Membership Ad-ministration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards via BritishStandards Online can

48、be found at information about BSI is available on the BSI website at www.bsi- subsists in all BSI publications. BSI also holds the copyright,in the UK, of the publications of the international standardization bodies. Ex-cept as permitted under the Copyright, Designs and Patents Act 1988 no ex-tract may be reproduced, stored in a retrieval system or transmitted in anyform or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the freeuse, in the course