1、Petroleum and natural gas industries - Glass-reinforced plastics (GRP) pipingPart 3: System design (ISO 14692-3:2017)BS EN ISO 14692-3:2017BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 14692-3 September 2017
2、ICS 75.200; 83.140.30 Supersedes EN ISO 14692-3:2002English Version Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - Part 3: System design (ISO 14692-3:2017) Industries du ptrole et du gaz naturel - Canalisations en plastique renforc de verre (PRV) - Partie 3: Concepti
3、on des systmes (ISO 14692-3:2017) Erdl- und Erdgasindustrie - Glasfaserverstrkte Kunststoffrohrleitungen (GFK) - Teil 3: Systemauslegung (ISO 14692-3:2017) This European Standard was approved by CEN on 22 June 2017. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stip
4、ulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European
5、Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the
6、 national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania
7、, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2017 CEN All rights of exploitation in any form a
8、nd by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 14692-3:2017 ENational forewordThis British Standard is the UK implementation of EN ISO 14692-3:2017. It is identical to ISO 14692-3:2017. It supersedes BS EN ISO 14692-3:2002, which is withdrawn.The UK participation in its
9、 preparation was entrusted to Technical Committee PSE/17/-/6, Processing equipment and systems for petroleum and natural gas industries.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary pro
10、visions of a contract. Users are responsible for its correct application. The British Standards Institution 2017 Published by BSI Standards Limited 2017ISBN 978 0 580 94760 5ICS 75.200; 83.140.30Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard wa
11、s published under the authority of the Standards Policy and Strategy Committee on 31 October 2017.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN ISO 146923:2017EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 14692-3 September 2017 ICS 75.200; 83.140.30
12、 Supersedes EN ISO 14692-3:2002English Version Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - Part 3: System design (ISO 14692-3:2017) Industries du ptrole et du gaz naturel - Canalisations en plastique renforc de verre (PRV) - Partie 3: Conception des systmes (ISO 1
13、4692-3:2017) Erdl- und Erdgasindustrie - Glasfaserverstrkte Kunststoffrohrleitungen (GFK) - Teil 3: Systemauslegung (ISO 14692-3:2017) This European Standard was approved by CEN on 22 June 2017. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions
14、for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in th
15、ree official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards b
16、odies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, S
17、lovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2017 CEN All rights of exploitation in any form and by any means reser
18、ved worldwide for CEN national Members. Ref. No. EN ISO 14692-3:2017 EBS EN ISO 146923:2017EN ISO 14692-3:2017 (E) 3 European foreword This document (EN ISO 14692-3:2017) has been prepared by Technical Committee ISO/TC 67 “Materials, equipment and offshore structures for petroleum, petrochemical and
19、 natural gas industries“ in collaboration with Technical Committee CEN/TC 12 “Materials, equipment and offshore structures for petroleum, petrochemical and natural gas industries” the secretariat of which is held by NEN. This European Standard shall be given the status of a national standard, either
20、 by publication of an identical text or by endorsement, at the latest by March 2018 and conflicting national standards shall be withdrawn at the latest by March 2018. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not b
21、e held responsible for identifying any or all such patent rights. This document supersedes EN ISO 14692-3:2002. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria
22、, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland
23、, Turkey and the United Kingdom. Endorsement notice The text of ISO 14692-3:2017 has been approved by CEN as EN ISO 14692-3:2017 without any modification. ISO 14692-3:2017(E)Foreword vIntroduction vi1 Scope . 12 Normative references 23 Terms and definitions . 34 Layout requirements 34.1 General . 34
24、.2 Space requirements 44.3 System supports. 44.3.1 General 44.3.2 Pipe-support contact surface 54.4 Isolation and access for cleaning . 54.5 Vulnerability 54.5.1 Point loads . 54.5.2 Abuse 54.5.3 Dynamic excitation and interaction with adjacent equipment and piping . 64.5.4 Exposure to light and ult
25、raviolet radiation . 64.5.5 Low temperatures and requirements for insulation 64.6 Fire and blast 65 Hydraulic design . 75.1 General . 75.2 Flow characteristics 75.3 General velocity limitations . 75.4 Erosion . 85.4.1 General 85.4.2 Particulate content . 85.4.3 Piping configuration . 85.4.4 Cavitati
26、on . 85.5 Water hammer 86 Generation of design envelopes 96.1 Partial factors . 96.1.1 Design life . 96.1.2 Chemical degradation 96.1.3 Fatigue and cyclic loading 96.2 Part factor, f2106.3 Combinations of part factor and partial factors 116.4 Design envelope 117 Stress analysis 137.1 Analysis method
27、s . 137.2 Pipe stress analysis software . 147.3 Analysis requirements . 147.4 Flexibility factors 147.5 Stress intensification factors 147.6 Modelling fittings . 157.7 Allowable deflections . 157.7.1 Vertical deflection in aboveground piping systems 157.7.2 Vertical deflection in buried piping syste
28、ms 157.8 Allowable stresses . 167.9 External pressure . 197.10 Axial compressive loading (buckling) 207.10.1 Shell buckling .207.10.2 Euler buckling . 20 ISO 2017 All rights reserved iiiContents PageBS EN ISO 146923:2017ISO 14692-3:2017(E)Foreword vIntroduction vi1 Scope . 12 Normative references 23
29、 Terms and definitions . 34 Layout requirements 34.1 General . 34.2 Space requirements 44.3 System supports. 44.3.1 General 44.3.2 Pipe-support contact surface 54.4 Isolation and access for cleaning . 54.5 Vulnerability 54.5.1 Point loads . 54.5.2 Abuse 54.5.3 Dynamic excitation and interaction with
30、 adjacent equipment and piping . 64.5.4 Exposure to light and ultraviolet radiation . 64.5.5 Low temperatures and requirements for insulation 64.6 Fire and blast 65 Hydraulic design . 75.1 General . 75.2 Flow characteristics 75.3 General velocity limitations . 75.4 Erosion . 85.4.1 General 85.4.2 Pa
31、rticulate content . 85.4.3 Piping configuration . 85.4.4 Cavitation . 85.5 Water hammer 86 Generation of design envelopes 96.1 Partial factors . 96.1.1 Design life . 96.1.2 Chemical degradation 96.1.3 Fatigue and cyclic loading 96.2 Part factor, f2106.3 Combinations of part factor and partial factor
32、s 116.4 Design envelope 117 Stress analysis 137.1 Analysis methods . 137.2 Pipe stress analysis software . 147.3 Analysis requirements . 147.4 Flexibility factors 147.5 Stress intensification factors 147.6 Modelling fittings . 157.7 Allowable deflections . 157.7.1 Vertical deflection in aboveground
33、piping systems 157.7.2 Vertical deflection in buried piping systems 157.8 Allowable stresses . 167.9 External pressure . 197.10 Axial compressive loading (buckling) 207.10.1 Shell buckling .207.10.2 Euler buckling . 20 ISO 2017 All rights reserved iiiContents PageBS EN ISO 146923:2017ISO 14692-3:201
34、7(E)7.10.3 Buckling pressure Buried piping .217.10.4 Upheaval buckling pressure 227.11 Longitudinal pressure expansion 238 Other design aspects .238.1 Fire 238.1.1 General. 238.1.2 Fire endurance 248.1.3 Fire reaction 248.1.4 Fire-protective coatings 258.2 Static electricity . 259 Installer and oper
35、ator documentation.26Annex A (normative) Cyclic de-rating factor A327Annex B (normative) Flexibility factors and stress intensification factors 29Bibliography .36iv ISO 2017 All rights reservedBS EN ISO 146923:2017ISO 14692-3:2017(E)7.10.3 Buckling pressure Buried piping .217.10.4 Upheaval buckling
36、pressure 227.11 Longitudinal pressure expansion 238 Other design aspects .238.1 Fire 238.1.1 General. 238.1.2 Fire endurance 248.1.3 Fire reaction 248.1.4 Fire-protective coatings 258.2 Static electricity . 259 Installer and operator documentation.26Annex A (normative) Cyclic de-rating factor A327An
37、nex B (normative) Flexibility factors and stress intensification factors 29Bibliography .36iv ISO 2017 All rights reserved ISO 14692-3:2017(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of prepa
38、ring International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in l
39、iaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC D
40、irectives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).Attention is drawn to the possibility that
41、 some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent dec
42、larations received (see www.iso.org/patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and expressions related to conformity
43、assessment, as well as information about ISOs adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following URL: www.iso.org/iso/foreword.html.This second edition cancels and replaces the first edition (ISO 14692-3:2002), which has been technic
44、ally revised. It also incorporates the Technical Corrigendum ISO 14692-3:2002/Cor 1:2005.This document was prepared by Technical Committee ISO/TC 67, Materials, equipment and offshore structures for petroleum, petrochemical and natural gas industries, Subcommittee SC 6, Processing equipment and syst
45、ems.A list of all the parts of ISO 14692 can be found on the ISO website. ISO 2017 All rights reserved vBS EN ISO 146923:2017ISO 14692-3:2017(E)IntroductionThe objective of this document is to ensure that piping systems, when designed using the components qualified in ISO 14692-2, will meet the spec
46、ified performance requirements. These piping systems are designed for use in oil and natural gas industry processing and utility service applications. The main users of the document will be the principal, design contractors, suppliers contracted to do the design, certifying authorities and governmen
47、t agencies.vi ISO 2017 All rights reservedBS EN ISO 146923:2017ISO 14692-3:2017(E)IntroductionThe objective of this document is to ensure that piping systems, when designed using the components qualified in ISO 14692-2, will meet the specified performance requirements. These piping systems are desig
48、ned for use in oil and natural gas industry processing and utility service applications. The main users of the document will be the principal, design contractors, suppliers contracted to do the design, certifying authorities and government agencies.vi ISO 2017 All rights reserved Petroleum and natur
49、al gas industries Glass-reinforced plastics (GRP) piping Part 3: System design1 ScopeThis document gives guidelines for the design of GRP piping systems. The requirements and recommendations apply to layout dimensions, hydraulic design, structural design, detailing, fire endurance, spread of fire and emissions and control of electrostatic discharge.This document is intended to be read in conjunction with ISO 14692-1.Guidance on the use of this document can be found in Figure 1, which is a more detailed flowchart of steps
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1