BS EN ISO 14919-2015 Thermal spraying Wires rods and cords for flame and arc spraying Classification Technical supply conditions《热喷涂 熔喷和电弧喷涂用线材、杆材和软线 分类 技术支持条件》.pdf

1、BSI Standards PublicationBS EN ISO 14919:2015Thermal spraying Wires,rods and cords for flame andarc spraying Classification Technical supply conditionsBS EN ISO 14919:2015 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN ISO14919:2015. It supersedes BS EN ISO 149

2、19:2001 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee STI/40, Thermal spraying and thermally sprayed coatings.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include

3、 all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2015. Published by BSI StandardsLimited 2015ISBN 978 0 580 80102 0ICS 25.220.20Compliance with a British Standard cannot confer immunity fromlegal obligations.This British

4、Standard was published under the authority of theStandards Policy and Strategy Committee on 31 January 2015.Amendments issued since publicationDate Text affectedEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 14919 January 2015 ICS 25.220.20 Supersedes EN ISO 14919:2001English Version Therm

5、al spraying - Wires, rods and cords for flame and arc spraying - Classification - Technical supply conditions (ISO 14919:2015) Projection thermique - Fils, baguettes et cordons pour projection thermique larc et au pistolet dans une flamme -Classification - Conditions techniques dapprovisionnement (I

6、SO 14919:2015) Thermisches Spritzen - Drhte, Stbe und Schnre zum Flammspritzen und Lichtbogenspritzen - Einteilung - Technische Lieferbedingungen (ISO 14919:2015) This European Standard was approved by CEN on 25 October 2014. CEN members are bound to comply with the CEN/CENELEC Internal Regulations

7、which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This

8、 European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN membe

9、rs are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portuga

10、l, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2015 CEN All rights of exploitation in any form

11、 and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 14919:2015 EBS EN ISO 14919:2015EN ISO 14919:2015 (E) 3 Foreword This document (EN ISO 14919:2015) has been prepared by Technical Committee CEN/TC 240 “Thermal spraying and thermally sprayed coatings” the secretariat of w

12、hich is held by DIN, in collaboration with Technical Committee ISO/TC 107 “Metallic and other inorganic coatings“. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by July 2015, and conflicting nation

13、al standards shall be withdrawn at the latest by July 2015. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes E

14、N ISO 14919:2001. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Mace

15、donia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. Endorsement notice The text of ISO 14919:2015 has been approved by CE

16、N as EN ISO 14919:2015 without any modification. BS EN ISO 14919:2015ISO 14919:2015(E)Contents PageForeword ivIntroduction v1 Scope . 12 Normative references 13 Classification 13.1 Classification according to the manufacturing process and resulting structure . 13.2 Classification according to materi

17、al groups and chemical composition . 13.2.1 Tin and tin alloys . 23.2.2 Zinc and zinc alloys 33.2.3 Aluminium and aluminium alloys . 43.2.4 Copper and copper alloys . 53.2.5 Iron and iron alloys 63.2.6 Nickel and nickel alloys 83.2.7 Molybdenum 93.2.8 Ceramics 94 Sizes and tolerances .105 Properties

18、 .115.1 Mechanical properties . 115.2 Surface properties . 115.3 Workability: Winding of wires . 126 Designation .127 Technical supply conditions 127.1 Forms of delivery . 127.2 Identification . 147.3 Packaging and storage . 148 Inspection documents 14 ISO 2015 All rights reserved iiiBS EN ISO 14919

19、:2015ISO 14919:2015(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a

20、subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission

21、 (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should

22、be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identi

23、fying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents).Any trade name used in this document is information given for the convenien

24、ce of users and does not constitute an endorsement.For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Su

25、pplementary informationISO 14919 was prepared by the European Committee for Standardization (CEN) Technical Committee CEN/TC 240, Thermal spraying and thermally sprayed coatings, in collaboration with ISO Technical Committee ISO/TC 107, Metallic and other inorganic coatings, in accordance with the a

26、greement on technical cooperation between ISO and CEN (Vienna Agreement).This second edition cancels and replaces the first edition (ISO 14919:2001), which has been technically revised.iv ISO 2015 All rights reservedBS EN ISO 14919:2015ISO 14919:2015(E)IntroductionRequests for official interpretatio

27、ns of any aspect of this standard should be directed to the secretariat of ISO/TC 107/WG 1 via your national standards body; a complete listing can be found at www.iso.org. ISO 2015 All rights reserved vBS EN ISO 14919:2015BS EN ISO 14919:2015Thermal spraying Wires, rods and cords for flame and arc

28、spraying Classification Technical supply conditions1 ScopeThis International Standard specifies requirements for classification of metal and non-metal wires (solid and cored), rods, cords processed by means of thermal spraying, especially by arc and flame spraying.2 Normative referencesThe following

29、 documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 10474:2013, Steel

30、 and steel products Inspection documentsISO 544:2011, Welding consumables Technical delivery conditions for filler materials and fluxes Type of product, dimensions, tolerances and markings3 Classification3.1 Classification according to the manufacturing process and resulting structureThe thermal spr

31、ay materials are classified according to the manufacturing process and the resulting structure, as given in Table 1.Table 1 Classification of thermal spraying material and resulting structureNumber Term Manufacturing process Structure1 solid wire/rod metallurgical manufacturing and forming homogeneo

32、us com-position2 solid wire/rod powder metallurgical manufacturing and forming homogeneous com-position3 cored wire (tube shaped wire)filling up a metal tube and compressed by means of forming seamless metal shell with powder filling4 cored wire (folded wire)forming a metal sheet with powder filling

33、, binder and com-pressed by means of drawingmetal shell with powder filling5 cords simultaneous extruding of powder, binder and organic sheath plastic shell with powder filling6 oxide ceramic rodsextruding and sintering respectively drying of ceramic mate-rialporous rod con-sisting of bonded ceramic

34、 particles3.2 Classification according to material groups and chemical compositionThe material groups are given in Table 2, and the chemical composition shall comply with Tables 3 to 10.INTERNATIONAL STANDARD ISO 14919:2015(E) ISO 2015 All rights reserved 1BS EN ISO 14919:2015ISO 14919:2015(E)Table

35、2 Classification according to material groupsCode Number Term1 tin and tin alloys2 zinc and zinc alloys3 aluminium and aluminium alloys4 copper and copper alloys5 iron and iron alloys6 nickel and nickel alloys7 molybdenum8 oxide ceramics3.2.1 Tin and tin alloysTable 3 Tin and tin alloysCode numberSy

36、mbolAlloying elements mass frac-tion in %Other elements mass fraction in %Manufacturing process1.1 Sn99 Sn 99,95 total 0,051Sb 0,02Ag 0,01Bi 0,002Cu 0,01Fe 0,01Pb 0,02Al+Cd+Zn 0,0021.2 SnSbCu84 Sb Cu remainder Sn7 to 8 3 to 4Pb 0,351As 0,1Bi 0,08Fe 0,1Al 0,01Zn 0,01other: total 0,22 ISO 2015 All rig

37、hts reservedBS EN ISO 14919:2015ISO 14919:2015(E)3.2.2 Zinc and zinc alloysTable 4 Zinc and zinc alloysCode numberSymbolAlloying elements mass fraction in %Other elements mass frac-tion in %Manufacturing process2.1 Zn99,99 Zn 99,99 total 0,0101Pb 0,007Cd 0,004Pb+Cd 0,011Sn 0,001Fe 0,005Cu 0,002other

38、: total 0,122.2 Zn99 Zn 99 total 1,01Pb 0,05Cd 0,005Pb+Cd 0,06Sn 0,001Fe 0,01Cu 0,7Mo 0,01Ti 0,16Mg 0,01Al 0,01other: total 0,122.3 ZnAl15 Zn Al84 to 86 14 to 16total 0,171Pb 0,007Cd 0,004Pb+Cd 0,011Sn 0,001Fe 0,02Cu 0,01Si 0,12 ISO 2015 All rights reserved 3BS EN ISO 14919:2015ISO 14919:2015(E)3.2.

39、3 Aluminium and aluminium alloysTable 5 Aluminium and aluminium alloysCode numberSymbolAlloying elements mass fraction in %Other elements mass frac-tion in %Manufactur-ing process3.2 Al99,5 Al 99,5 total 0,31Si 0,25Fe 0,40Ti 0,02Cu 0,02Zn 0,07Mn 0,02other: particular 0,033.3 AlMg5 Mg Mn Cr Ti remain

40、der Al4,5 to 5,6 0,05 to 0,20 0,05 to 0,20 0,06 to 0,20total 0,91Si 0,30Fe 0,40Cu 0,10Zn 0,10other: particular 0,153.4 AlZn5 Zn remainder Al4,5 to 5,1 total 11Si 0,30Fe 0,40Cu 0,05Sn 0,20other: particular 0,053.5 AlSi5 Si remainder Al4,5 to 6,0 total 11Si 0,30Fe 0,80Cu 0,30Mn 0,05Mg 0,05Zn 0,10Sn 0,

41、20other: particular 0,154 ISO 2015 All rights reservedBS EN ISO 14919:2015ISO 14919:2015(E)Code numberSymbolAlloying elements mass fraction in %Other elements mass frac-tion in %Manufactur-ing process3.6 AlSi12 Si remainder Al11,0 to 13,0 total 11Fe 0,80Cu 0,30Mn 0,15Mg 0,10Zn 0,20Ti 0,15other parti

42、cular: 0,05other total: 0,153.2.4 Copper and copper alloysTable 6 Copper and copper alloysCode numberSymbolAlloying elements mass fraction in %Other elements mass frac-tion in %Manufacturing process4.1 Cu99 Cu 99,9 other 0,01 14.2 CuZn37 Cu remainder Zn62,0 to 64 Al 0,031Fe 0,1Mn 0,1Ni 0,3Pb 0,1Sb 0

43、,01Sn 0,1other: total 0,54.3 CuZn39 Cu Sn Si remainder Zn56 to 62 0,5 to 1,5 0,1 to 0,5Ni 1,51Mn 1,0Fe 0,5Al 0,01Pb 0,03other: total 0,24.4 CuSn6 Sn remainder Cu5,0 to 8,0 Fe 0,11Al 0,01Zn 0,1Pb 0,02P 0,01 to 0,4other: total 0,4Table 5 (continued) ISO 2015 All rights reserved 5BS EN ISO 14919:2015IS

44、O 14919:2015(E)Code numberSymbolAlloying elements mass fraction in %Other elements mass frac-tion in %Manufacturing process4.6 CuAl8 Al remainder Cu7,5 to 9,5 Mn 1,81Ni 0,8Fe 0,5Si 0,2Zn 0,2other: total 0,54.7 CuAl10 Al Fe remainder Cu8,5 to 11 0,5 to 1,5Ni+Co 1,01Pb 0,02Si 0,1Mn 0,03Zn 0,02other: t

45、otal 0,33.2.5 Iron and iron alloysTable 7 Iron and iron alloysCode numberSymbolAlloying elements mass fraction in %Other elements mass fraction in %Manufactur-ing process5.1 10Mn C Mn remainder Fe0,04 to 0,12 0,42 to 0,68Si traces1Cr 0,15Cu 0,20Ni 0,15P 0,030S 0,0305.3 80MnSi C Si Mn remainder Fe0,8

46、 to 0,85 0,15 to 0,35 0,50 to 0,70P S 0,035 0,03515.6 110MnCrTi55 C Si Mn Cr remainder Fe0,97 to 1,23 0,12 to 0,38 1,76 to 2,27 1,65 to 1,95 Ti P S0,13 to 0,35 0,025 0,025 15.7 X45Cr13 a) with Cu plating b) without Cu platingC Si Mn Cr remainder Fe0,3 to 0,50 1,0 1,0 12 to 14P S 0,045 0,03015.8 X20C

47、rMo131 C Si Mn Cr Mo remainder Fe0,17 to 0,22 1,0 1,0 12 to 14 0,9 to 1,3 Ni P S 1,0 0,045 0,0301Table 6 (continued)6 ISO 2015 All rights reservedBS EN ISO 14919:2015ISO 14919:2015(E)Code numberSymbolAlloying elements mass fraction in %Other elements mass fraction in %Manufactur-ing process5.9 X 6Cr

48、Al224 C Si Mn Al Cr remainder Fe 0,055 0,65 0,45 3,5 to 5,5 21 to 23P S 0,040 0,02515.10 X6CrNi199 C Si Mn Cr Ni remainder Fe 0,06 1,5 2,0 18 to 20 8,5 to 10,5P S 0,030 0,02015.11 (X5CrNiMo17122)aC Si Mn Cr Mo Ni remainder Fe 0,08 1,0 2,0 16,5 to 18,5 2 to 2,5 10,5 to 13,5P S 0,045 0,0301, 45.12 (X12CrNiMn188-6)aC Si Mn Cr Ni remainder Fe 0,20 1,0 5,5 to 8,0 17 to 20 7,5 to 9,5P S 0,040 0,0251, 45.13 X12CrNi2520 C Si Mn Cr Ni remainder Fe 0,15 1,5 1,5 to 3,5 24 to 27 19 to 22P S 0,025 0,02015.14 X25CrCuB263-3 C