BS EN ISO 15012-4-2016 Health and safety in welding and allied processes Equipment for capture and separation of welding fume General requirements《焊接和相关工艺的卫生与安全 焊接烟尘捕获和分离设备 通用要求》.pdf

1、BS EN ISO 15012-4:2016Health and safety in weldingand allied processes Equipment for capture andseparation of welding fumePart 4: General requirements (ISO15012-4:2016)BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06BS EN ISO 15012-4:2016 BRITISH STANDARDNational for

2、ewordThis British Standard is the UK implementation of EN ISO15012-4:2016. The UK participation in its preparation was entrusted to TechnicalCommittee WEE/40, Health and safety in welding.A list of organizations represented on this committee can beobtained on request to its secretary.This publicatio

3、n does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2016.Published by BSI Standards Limited 2016ISBN 978 0 580 76826 2ICS 25.160.30Compliance with a British Standard cannot confer immunity fromle

4、gal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 31 July 2016.Amendments/corrigenda issued since publicationDate T e x t a f f e c t e dEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 15012-4 July 2016 ICS 25.160.30 Eng

5、lish Version Health and safety in welding and allied processes - Equipment for capture and separation of welding fume - Part 4: General requirements (ISO 15012-4:2016) Hygine et scurit en soudage et techniques connexes - quipements de captage et de filtration des fumes de soudage - Partie 4: Exigenc

6、es gnrales (ISO 15012-4:2016) Arbeits- und Gesundheitsschutz beim Schweien und bei verwandten Verfahren - Einrichtungen zum Erfassen und Abscheiden von Schweirauch - Teil 4: Allgemeine Anforderungen (ISO 15012-4:2016) This European Standard was approved by CEN on 15 April 2016. CEN members are bound

7、 to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN

8、-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre ha

9、s the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Lu

10、xembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey andUnited Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brus

11、sels 2016 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 15012-4:2016 EBS EN ISO 15012-4:2016EN ISO 15012-4:2016 (E) 3 European foreword This document (EN ISO 15012-4:2016) has been prepared by Technical Committee ISO/TC 44 “W

12、elding and allied processes” in collaboration with Technical Committee CEN/TC 121 “Welding and allied processes” the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the late

13、st by January 2017, and conflicting national standards shall be withdrawn at the latest by January 2017. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all s

14、uch patent rights. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive(s). For relationship with EU Directive, see informative Annex ZA, which is an integral part of this

15、document. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, F

16、rance, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. Endorsement notice The text of ISO 15012-4:2016 has been approved by CEN as E

17、N ISO 15012-4:2016 without any modification. BS EN ISO 15012-4:2016EN ISO 15012-4:2016 (E) 4 Annex ZA (informative) Relationship between this European Standard and the essential requirements of EU Directive 2006/42/EC aimed to be covered This European Standard has been prepared under a Commissions s

18、tandardization request M/396 (Machinery) to provide one voluntary means of conforming to essential requirements of Directive 2006/42/EC of the European Parliament and of the Council of 17 May 2006 on machinery, and amending Directive 95/16/EC (recast). Once this standard is cited in the Official Jou

19、rnal of the European Union under that Directive, compliance with the normative clauses of this standard given in Table ZA.1 confers, within the limits of the scope of this standard, a presumption of conformity with the corresponding essential requirements of that EU Directive 2006/42/EC, and associa

20、ted EFTA regulations. Table ZA.1 Correspondence between this European Standard and EU Directive 2006/42/EC Essential Requirements of EU Directive 2006/42/EC Clause(s)/subclause(s) of this EN Remarks/Notes all requirements are covered all clauses WARNING 1 Presumption of conformity stays valid only a

21、s long as a reference to this European Standard is maintained in the list published in the Official Journal of the European Union. Users of this standard should consult frequently the latest list published in the Official Journal of the European Union. WARNING 2 Other Union legislation may be applic

22、able to the product(s) falling within the scope of this standard. BS EN ISO 15012-4:2016ISO 15012-4:2016(E)Foreword ivIntroduction v1 Scope . 12 Normative references 13 Terms and definitions . 23.9 Extraction device . 34 Significant hazards . 35 Requirements and verifications . 35.1 General . 35.2 W

23、elding fume separation equipment 35.3 Extraction devices 45.4 Flexible arms, hoses and hoods 45.5 Ducting properties . 55.6 Spark arrestor 65.7 Separation efficiency 65.8 Filter cleaning system . 75.9 Filter changing. 75.10 Waste handling . 75.11 Air mover . 75.12 Signals/indicators 85.13 Exhaust an

24、d cooling air . 96 Instructions for use . 97 Marking .10Annex A (informative) Malfunctions and determination of minimum airflow .11Bibliography .12 ISO 2016 All rights reserved iiiContents PageBS EN ISO 15012-4:2016ISO 15012-4:2016(E)ForewordISO (the International Organization for Standardization) i

25、s a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represe

26、nted on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop

27、 this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IE

28、C Directives, Part 2 (see www.iso.org/directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the

29、development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the meaning of

30、ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary informationThe committee responsible for this document is ISO/TC 44, Welding

31、 and allied processes, Subcommittee SC 9, Health and safety.ISO 15012 consists of the following parts, under the general title Health and safety in welding and allied processes Equipment for capture and separation of welding fume : Part 1: Requirements for testing and marking of separation efficienc

32、y Part 2: Determination of the minimum air volume flow rate of captor hoods and nozzles Part 3: Determination of the capture efficiency of on-gun welding fume extraction devices Part 4: General requirementsRequests for official interpretations of any aspect of this International Standard should be d

33、irected to the Secretariat of ISO/TC 44/SC 9 via your national standards body. A complete listing of these bodies can be found at www.iso.org.iv ISO 2016 All rights reservedBS EN ISO 15012-4:2016ISO 15012-4:2016(E)IntroductionWelding and allied processes generate fumes and gases which, if inhaled, c

34、an be harmful to human health. Therefore, control of the fumes and gases generated is to be exercised to minimize worker exposure.The most effective method of control is to capture the fumes and gases close to their source before they enter a workers breathing zone or the general workplace environme

35、nt.Ventilation equipment used to capture the fumes and gases is to be fit for purpose because inefficient capture could result in high exposure and can be detrimental to workers health. It is important therefore that it adheres to defined manufacturing, materials and design requirements and gives wa

36、rning of malfunction.This part of ISO 15012 defines the general requirements that are necessary for ventilation equipment to maintain exposure to fumes at acceptable levels.This part of ISO 15012 is a type-B standard as stated in ISO 12100.This part of ISO 15012 is of relevance, in particular, for t

37、he following stakeholder groups representing the market players with regard to machinery safety: machine manufacturers (small, medium and large enterprises); health and safety bodies (regulators, accident prevention organizations, market surveillance, etc.).Others can be affected by the level of mac

38、hinery safety achieved with the means of this part of ISO 15012 by the above-mentioned stakeholder groups: machine users/employers (small, medium and large enterprises); machine users/employees (e.g. trade unions, organizations for people with special needs); service providers, e.g. for maintenance

39、(small, medium and large enterprises); consumers (in case of machinery intended for use by consumers).The above-mentioned stakeholder groups have been given the possibility to participate at the drafting process of this part of ISO 15012.In addition, this part of ISO 15012 is intended for standardiz

40、ation bodies elaborating type-C standards.The requirements of this part of ISO 15012 can be supplemented or modified by a type-C standard.For machines which are covered by the scope of a type-C standard and which have been designed and built according to the requirements of that standard, the requir

41、ements of that type-C standard take precedence. ISO 2016 All rights reserved vBS EN ISO 15012-4:2016BS EN ISO 15012-4:2016Health and safety in welding and allied processes Equipment for capture and separation of welding fume Part 4: General requirements1 ScopeThis part of ISO 15012 defines the gener

42、al requirements for ventilation equipment used to control exposure to fumes generated by welding and allied processes. It applies to the design and manufacture of all parts of the equipment including hoods, ducting, filter units, air movers, systems that inform of unsafe operation and workplace prac

43、tices to ensure safe working with regard to exposure.Significant hazards are listed in Clause 4. It does not cover electrical, mechanical and pneumatic hazards.This part of ISO 15012 is applicable to the following: local exhaust ventilation systems (LEV); mobile and stationary equipment.This part of

44、 ISO 15012 is not applicable to the following: general ventilation, air make up or air movement systems; air conditioning systems; separation of gases generated by or used by welding and allied processes; LEV used for welding and allied processes that generate reactive potentially explosive particle

45、s and atmospheres; grinding dust.This part of ISO 15012 applies to systems designed and manufactured after its publication.2 Normative referencesThe following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references,

46、only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 12100:2010, Safety of machinery General principles for design Risk assessment and risk reductionISO 15012-1:2013, Health and safety in welding and allied proce

47、sses Equipment for capture and separation of welding fume Part 1: Requirements for testing and marking of separation efficiencyISO 15012-2, Health and safety in welding and allied processes Requirements, testing and marking of equipment for air filtration Part 2: Determination of the minimum air vol

48、ume flow rate of captor hoods and nozzlesISO 15012-3, Health and safety in welding and allied processes Requirements, testing and marking of equipment for air filtration Part 3: Determination of the capture efficiency of on-gun welding fume extractionINTERNATIONAL STANDARD ISO 15012-4:2016(E) ISO 20

49、16 All rights reserved 1BS EN ISO 15012-4:2016ISO 15012-4:2016(E)IEC 60204-1:2005, Safety of machinery Electrical equipment of machines Part 1: General requirementsIEC 60335-2-69, Household and similar electrical appliances Safety Part 2-69: Particular requirements for wet and dry vacuum cleaners, including power brush, for commercial useIEC 60695-2-12, Fire hazard testing Part 2-12: Glowing/hot-wire based test methods Glow-wire flammability index (GWFI) test method for materials3 Terms and defini