BS EN ISO 15023-1-2017 Plastics Poly(vinyl alcohol) (PVAL) materials Designation system and basis for specifications《塑料 聚乙烯醇(PVAL)材料 规范用命名体系和规范基础》.pdf

1、Plastics Poly(vinyl alcohol) (PVAL) materialsPart 1: Designation system and basis for specificationsBS EN ISO 150231:2017BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06National forewordThis British Standard is the UK implementation of EN ISO 150231:2017. It is ident

2、ical to ISO 150231:2017. It supersedes BS EN ISO 150231:2006, which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee PRI/82, Thermoplastic materials.A list of organizations represented on this committee can be obtained on request to its secretary.This publica

3、tion does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2017 Published by BSI Standards Limited 2017ISBN 978 0 580 85271 8ICS 83.080.20Compliance with a British Standard cannot confer immunity f

4、rom legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 May 2017.Amendments/corrigenda issued since publicationDate Text affected BRITISH STANDARDBS EN ISO 150231:2017EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN ISO 1502

5、31April 2017ICS 83.080.20 Supersedes EN ISO 150231:2006EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGCENCENELEC Management Centre: Avenue Marnix 17, B1000 Brussels 2017 CEN Ref. No. EN ISO 150231:2017: EAll rights of exploitation in any form and by

6、 any means reserved worldwide for CEN national MembersPlastics Poly(vinyl alcohol) (PVAL) materials Part 1: Designation system and basis for specifications (ISO 150231:2017) Plastiques Matriaux en poly(alcool de vinyle) (PVAL) Partie 1: Systme de dsignation et base de spcifications (ISO 15023-1:2017

7、) Kunststoffe Polyvinylalkohol (PVAL)Formmassen Teil 1: Bezeichnungssystem und Basis fr Spezifikationen (ISO 15023-1:2017) This European Standard was approved by CEN on 20 March 2017.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving t

8、his European Standard the status of a national standard without any alteration. Uptodate lists and bibliographical references concerning such national standards may be obtained on application to the CENCENELEC Management Centre or to any CEN member.This European Standard exists in three official ver

9、sions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.CEN members are the national standards bodies of Austria,

10、 Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, S

11、weden, Switzerland, Turkey and United Kingdom.English VersionEN ISO 150231:2017 (E)European forewordThis document (EN ISO 150231:2017) has been prepared by Technical Committee ISO/TC 61 “Plastics” in collaboration with Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by NBN

12、.This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 2017, and conflicting national standards shall be withdrawn at the latest by October 2017.Attention is drawn to the possibility that some o

13、f the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights.This document supersedes EN ISO 150231:2006.According to the CENCENELEC Internal Regulations, the national standards organizations of th

14、e following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherl

15、ands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.Endorsement noticeThe text of ISO 150231:2017 has been approved by CEN as EN ISO 150231:2017 without any modification.iiBS EN ISO 150231:2017ISO 150231:2017(E)Foreword iv1 S

16、cope . 12 Normative references 13 Terms and definitions . 14 Designation system 24.1 General . 24.2 Data block 1 . 24.3 Data block 2 . 24.4 Data block 3 . 34.5 Data block 4 . 44.5.1 General 44.5.2 Degree of hydrolysis . 44.5.3 Viscosity of 4 % aqueous solution 54.6 Data block 5 . 65 Examples of desi

17、gnations 6Bibliography 7 ISO 2017 All rights reserved iiiContents PageBS EN ISO 150231:2017ISO 150231:2017(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is n

18、ormally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and nongovernmental, in liaison with ISO, also take part in

19、 the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular t

20、he different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).Attention is drawn to the possibility that some of the elements of this docu

21、ment may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.or

22、g/patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and expressions related to conformity assessment, as well as information

23、 about ISOs adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following URL: www.iso.org/iso/foreword.html.This document was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 9, Thermoplastic materials.This second edition c

24、ancels and replaces the first edition (ISO 15023-1:2001), which has been technically revised.A list of all parts in the ISO 15023 series can be found on the ISO website.iv ISO 2017 All rights reservedBS EN ISO 150231:2017Plastics Poly(vinyl alcohol) (PVAL) materials Part 1: Designation system and ba

25、sis for specifications1 ScopeThis document establishes a system of designation for poly(vinyl alcohol) (PVAL) materials which may be used as the basis for specifications.The types of poly(vinyl alcohol) (PVAL) materials are differentiated from each other by a classification system based on the desig

26、natory properties:a) degree of hydrolysis,b) viscosity of aqueous solution under defined conditionsand on information about basic polymer parameters, intended application and/or method of processing, important properties, additives, colorants, fillers and reinforcing materials.This document is appli

27、cable to all poly(vinyl alcohol) (PVAL) materials with a degree of hydrolysis not less than 70 mol%.It applies to materials ready for normal use in the form of powder, granules or pellets and to materials unmodified or modified by colorants, additives, fillers, etc.It is not intended to imply that m

28、aterials having the same designation give necessarily the same performance. This document does not provide engineering data, performance data or data on processing conditions which may be required to specify a material. If such additional properties are required, they are intended to be determined i

29、n accordance with the test methods specified in ISO 15023-2, if suitable.In order to designate a thermoplastic material to meet particular specifications, the requirements are given in data block 5 (see 4.1).2 Normative referencesThe following documents are referred to in the text in such a way that

30、 some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 472, Plastics VocabularyISO 10431, Plastics Symbols and abbrevia

31、ted terms Part 1: Basic polymers and their special characteristicsISO 150232:1), Plastics Poly(vinyl alcohol) (PVAL) materials Part 2: Determination of properties3 Terms and definitionsFor the purposes of this document, the terms and definitions given in ISO 472 apply.1) Under preparation. Stage at

32、the time of publication: ISO/DIS 150232:2016.INTERNATIONAL STANDARD ISO 150231:2017(E) ISO 2017 All rights reserved 1BS EN ISO 150231:2017ISO 150231:2017(E)ISO and IEC maintain terminological databases for use in standardization at the following addresses: IEC Electropedia: available at http:/www.el

33、ectropedia.org/ ISO Online browsing platform: available at http:/www.iso.org/obp4 Designation system4.1 GeneralThe designation system for thermoplastics is based on the following standardized pattern:DesignationIdentity blockDescription block (optional)International Standard number blockIndividualit

34、em blockData block 1Data block 2Data block 3Data block 4Data block 5The designation consists of an optional description block, reading “Thermoplastics”, and an identity block comprising the International Standard number and an individualitem block. For unambiguous designation, the individual-item bl

35、ock is subdivided into five data blocks comprising the following information:Data block 1: Identification of the plastic by its abbreviated term, PVAL, in accordance with ISO 10431 (see 4.2).Data block 2: Fillers or reinforcing materials and their nominal content (see 4.3).Data block 3: Position 1:

36、Intended application and/or method of processing (see 4.4).Positions 2 to 8: Information about important properties, additives and colour (see 4.4).Data block 4: Designatory properties (see 4.5).Data block 5: For the purpose of specifications, the fifth data block contains appropriate information (s

37、ee 4.6).The first character of the individual-item block shall be a hyphen. The data blocks shall be separated from each other by commas.If a data block is not used, this shall be indicated by doubling the separation sign, i.e. by two commas (,).Terminal commas may be omitted. For part marking, the

38、first two blocks of the designation are used, connected with a hyphen, and placed between the punctuation marks “ and “2 but 405 4 but 607 6 but 809 8 but 1011 10 but 1213 12 but 1415 14 but 1617 16 but 1819 18 but 2022 20 but 2426 24 but 2830 28 but 3234 32 but 3638 36 but 4042 40 but 4547 45 but 5

39、052 50 but 55 ISO 2017 All rights reserved 5BS EN ISO 150231:2017ISO 150231:2017(E)CodenumberRange of viscosity mPas57 55 but 6065 60 but 7075 70 but 8085 80 but 9095 90 but 100150 100 but 150175 150 but 200200 2004.6 Data block 5Indication of additional requirements in this data block transforms th

40、e designation of a material into a specification for a particular material. This may be done, for example, by reference to a suitable national standard or to a standard-like, generally established specification.5 Examples of designationsA thermoplastic poly(vinyl alcohol) (PVAL) material filled with

41、 synthetic material (S) powder (D) and a filler content of 5 % (per mass) (05), intended for adhesives (A), antiblocking (B) and beads (G3), and with degree of hydrolysis of 98 mol% (099) and the viscosity of 4 % aqueous solution of 25 mPas (26), with no additional information, would be designated:D

42、esignation: Thermoplastics ISO 150231PVAL,SD05,ABG3,09926Or: ISO 150231PVAL,SD05,ABG3,09926Part marking: PVAL SD056 ISO 2017 All rights reservedBS EN ISO 150231:2017ISO 150231:2017(E)Bibliography1 ISO 10432, Plastics Symbols and abbreviated terms Part 2: Fillers and reinforcing materials ISO 2017 Al

43、l rights reserved 7BS EN ISO 150231:2017This page deliberately left blankThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. British Standards an

44、d other standardization products are published by BSI Standards Limited.British Standards Institution (BSI)About usWe bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge embodie

45、d in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your organi

46、zation needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, including British and adopted European and international standards, throu

47、gh our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team.Copyright in BSI publicationsAll the content in BSI publications, including British S

48、tandards, is the property of and copyrighted by BSI or some person or entity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed such information to BSI for commercial publication and use.Save for the provisions below, you may not

49、transfer, share or disseminate any portion of the standard to any other person. You may not adapt, distribute, commercially exploit, or publicly display the standard or any portion thereof in any manner whatsoever without BSIs prior written consent.Storing and using standardsStandards purchased in soft copy format: A British Standard purchased in soft copy format is licensed to a sole named user for p